[PATCH] arm64: dts: imx8mn-var-som-symphony: fix USB OTG

[Fabio Estevam]

Adding some Variscite folks in case they can help to clarify.

On Tue, Jul 4, 2023 at 1:20 PM Krzysztof Kozlowski
<krzysztof.kozlowski at linaro.org> wrote:
>
> On 04/07/2023 17:31, Hugo Villeneuve wrote:
> > On Tue, 4 Jul 2023 17:08:12 +0200
> > Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org> wrote:
> >
> >> On 04/07/2023 17:02, Hugo Villeneuve wrote:
> >>> From: Hugo Villeneuve <hvilleneuve at dimonoff.com>
> >>>
> >>> USB OTG is currently broken on the Variscite Symphony EVK and imx8mn
> >>> nano SOM.
> >>>
> >>> Import changes from linux-5.15 branch of  doen't giveto fix it.
> >>>
> >>> Link: https://github.com/varigit/linux-imx.git
> >>> Fixes: 7358e05bddca ("arm64: dts: imx8mn-var-som-symphony: Add Variscite Symphony board with VAR-SOM-MX8MN")
> >>> Signed-off-by: Hugo Villeneuve <hvilleneuve at dimonoff.com>
> >>> ---
> >>>  .../dts/freescale/imx8mn-var-som-symphony.dts | 37 ++++++++++++++++++-
> >>>  1 file changed, 35 insertions(+), 2 deletions(-)
> >>>
> >>> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
> >>> index 406a711486da..aef89198f24c 100644
> >>> --- a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
> >>> +++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
> >>> @@ -6,6 +6,7 @@
> >>>
> >>>  /dts-v1/;
> >>>
> >>> +#include <dt-bindings/usb/pd.h>
> >>>  #include "imx8mn-var-som.dtsi"
> >>>
> >>>  / {
> >>> @@ -104,10 +105,29 @@ extcon_usbotg1: typec at 3d {
> >>>             compatible = "nxp,ptn5150";
> >>>             reg = <0x3d>;
> >>>             interrupt-parent = <&gpio1>;
> >>> -           interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
> >>> +           interrupts = <11 IRQ_TYPE_NONE>;
> >>
> >> That's surprising, why?
> >
> > Hi,
> > the varigit repos log or source code has no information about this
> > particular configuration.
> >
> > In the schematics, the interrupt output pin of the PTN5150 is connected
> > to two different resistors, one of these being connected to GPIO1 pin
> > 11. But these two resistors are not assembled on any versions of the
> > board, so the interrupt pin is currently not used.
>
> OK, so there is no interrupt, but not interrupt of type none. Just drop
> the property and make it optional in the bindings. The driver however
> requires the interrupt, so I wonder how the device is going to work
> without it?
>
> Are you sure that interrupt line is not shorted instead of missing resistor?
>
> Best regards,
> Krzysztof
>