[PATCH 1/1] arm64: dts: imx8mm-tqma8mqml-mba8mx: Fix USB DR

[Alexander Stein]

Hello Shawn,

Am Montag, 24. Oktober 2022, 03:31:23 CEST schrieb Shawn Guo:
> On Mon, Sep 26, 2022 at 01:26:22PM +0200, Alexander Stein wrote:
> > extcon does not work somehow, so switch to usb-role-switch instead.
> 
> So extcon was added without testing?

It had been tested, but apparently only the USB Host case :( extcon itself 
does work and detects ID pin correctly. Cable states switch when a USB device 
(mass storage) is attached and removed, thus mass storage is detect and 
usable.
But unfortunately this is not the case for USB device using g_serial udc 
driver. IMHO this seems to be a problem within chipidea usb driver.
Using usb-role-switch instead, both USB host and USB device do work.

Best regards,
Alexander

> Shawn
> 
> > Fixes: dfcd1b6f7620 ("arm64: dts: freescale: add initial device tree for
> > TQMa8MQML with i.MX8MM") Signed-off-by: Alexander Stein
> > <alexander.stein at ew.tq-group.com>
> > ---
> > 
> >  .../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 32 +++++++++++++++----
> >  1 file changed, 26 insertions(+), 6 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> > b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts index
> > bfb44630da6b..56323c989d55 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> > +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> > @@ -34,11 +34,25 @@ reg_usdhc2_vmmc: regulator-vmmc {
> > 
> >  		off-on-delay-us = <12000>;
> >  	
> >  	};
> > 
> > -	extcon_usbotg1: extcon-usbotg1 {
> > -		compatible = "linux,extcon-usb-gpio";
> > +	connector {
> > +		compatible = "gpio-usb-b-connector", "usb-b-connector";
> > +		type = "micro";
> > +		label = "X19";
> > 
> >  		pinctrl-names = "default";
> > 
> > -		pinctrl-0 = <&pinctrl_usb1_extcon>;
> > -		id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> > +		pinctrl-0 = <&pinctrl_usb1_connector>;
> > +		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
> > +
> > +		ports {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +
> > +			port at 0 {
> > +				reg = <0>;
> > +				usb_dr_connector: endpoint {
> > +					remote-endpoint = 
<&usb1_drd_sw>;
> > +				};
> > +			};
> > +		};
> > 
> >  	};
> >  
> >  };
> > 
> > @@ -106,13 +120,19 @@ &usbotg1 {
> > 
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&pinctrl_usbotg1>;
> >  	dr_mode = "otg";
> > 
> > -	extcon = <&extcon_usbotg1>;
> > 
> >  	srp-disable;
> >  	hnp-disable;
> >  	adp-disable;
> >  	power-active-high;
> >  	over-current-active-low;
> > 
> > +	usb-role-switch;
> > 
> >  	status = "okay";
> > 
> > +
> > +	port {
> > +		usb1_drd_sw: endpoint {
> > +			remote-endpoint = <&usb_dr_connector>;
> > +		};
> > +	};
> > 
> >  };
> >  
> >  &usbotg2 {
> > 
> > @@ -242,7 +262,7 @@ pinctrl_usbotg1: usbotg1grp {
> > 
> >  			   <MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		
0x84>;
> >  	
> >  	};
> > 
> > -	pinctrl_usb1_extcon: usb1-extcongrp {
> > +	pinctrl_usb1_connector: usb1-connectorgrp {
> > 
> >  		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		
0x1c0>;
> >  	
> >  	};