[RESEND PATCH 18/19] arm64: allwinner: a100: Add MMC related nodes

[André Przywara]

On 10/11/2020 06:48, Frank Lee wrote:

Hi,

> From: Yangtao Li <frank at allwinnertech.com>
> 
> The A100 has 3 MMC controllers, one of them being especially targeted to
> eMMC. Let's add nodes on dts.
> 
> Signed-off-by: Yangtao Li <frank at allwinnertech.com>

I don't have a datasheet nor a device for testing, but at least I could
check the pins against the pinctrl driver, and compare the MMC nodes
against the H6. Apart from the interrupts they are the same, so:

Reviewed-by: Andre Przywara <andre.przywara at arm.com>

Cheers,
Andre

> ---
>  .../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 71 +++++++++++++++++++
>  1 file changed, 71 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
> index c731bb9727c2..4adfc7d4854a 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
> @@ -169,12 +169,83 @@ pio: pinctrl at 300b000 {
>  			interrupt-controller;
>  			#interrupt-cells = <3>;
>  
> +			mmc0_pins: mmc0-pins {
> +				pins = "PF0", "PF1", "PF2", "PF3",
> +				       "PF4", "PF5";
> +				function = "mmc0";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			/omit-if-no-ref/
> +			mmc1_pins: mmc1-pins {
> +				pins = "PG0", "PG1", "PG2", "PG3",
> +				       "PG4", "PG5";
> +				function = "mmc1";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
> +			mmc2_pins: mmc2-pins {
> +				pins = "PC0", "PC1", "PC5", "PC6",
> +				       "PC8", "PC9", "PC10", "PC11",
> +				       "PC13", "PC14", "PC15", "PC16";
> +				function = "mmc2";
> +				drive-strength = <30>;
> +				bias-pull-up;
> +			};
> +
>  			uart0_pb_pins: uart0-pb-pins {
>  				pins = "PB9", "PB10";
>  				function = "uart0";
>  			};
>  		};
>  
> +		mmc0: mmc at 4020000 {
> +			compatible = "allwinner,sun50i-a100-mmc";
> +			reg = <0x04020000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC0>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc0_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc1: mmc at 4021000 {
> +			compatible = "allwinner,sun50i-a100-mmc";
> +			reg = <0x04021000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC1>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc1_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		mmc2: mmc at 4022000 {
> +			compatible = "allwinner,sun50i-a100-emmc";
> +			reg = <0x04022000 0x1000>;
> +			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> +			clock-names = "ahb", "mmc";
> +			resets = <&ccu RST_BUS_MMC2>;
> +			reset-names = "ahb";
> +			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&mmc2_pins>;
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
>  		uart0: serial at 5000000 {
>  			compatible = "snps,dw-apb-uart";
>  			reg = <0x05000000 0x400>;
>