[RESEND PATCH 18/19] arm64: allwinner: a100: Add MMC related nodes

[Frank Lee]

From: Yangtao Li <frank at allwinnertech.com>

The A100 has 3 MMC controllers, one of them being especially targeted to
eMMC. Let's add nodes on dts.

Signed-off-by: Yangtao Li <frank at allwinnertech.com>
---
 .../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 71 +++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
index c731bb9727c2..4adfc7d4854a 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
@@ -169,12 +169,83 @@ pio: pinctrl at 300b000 {
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			/omit-if-no-ref/
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC0", "PC1", "PC5", "PC6",
+				       "PC8", "PC9", "PC10", "PC11",
+				       "PC13", "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
 			uart0_pb_pins: uart0-pb-pins {
 				pins = "PB9", "PB10";
 				function = "uart0";
 			};
 		};
 
+		mmc0: mmc at 4020000 {
+			compatible = "allwinner,sun50i-a100-mmc";
+			reg = <0x04020000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc at 4021000 {
+			compatible = "allwinner,sun50i-a100-mmc";
+			reg = <0x04021000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc at 4022000 {
+			compatible = "allwinner,sun50i-a100-emmc";
+			reg = <0x04022000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		uart0: serial at 5000000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x05000000 0x400>;
-- 
2.28.0