Does 99x0 support mesh mode?

[Yu-Chieh]

OK, i think it's not supported now
# iw phy phy0 interface add mp0 type mp mesh_id MeshNetwork
# ifconfig mp0 up
[  289.502405] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16  peers: 528  ti
d: 132
[  289.510058] ath10k_pci 0003:01:00.0: msdu-desc: 1424  skid: 32
[  289.604802] ath10k_pci 0003:01:00.0: must load driver with rawmode=1 to add m
esh interfaces
ifconfig: SIOCSIFFLAGS: Invalid argument

then, i tried insmod ath10k_core.ko with rawmode=1, i got probe fw
fail log as following
[  350.779002] ath10k_pci 0003:01:00.0: rawmode = 1 requires support from firmwa
re
[  350.786294] ath10k_pci 0003:01:00.0: fatal problem with firmware features: -2
2
[  350.793575] ath10k_pci 0003:01:00.0: could not probe fw (-22)

Jay

2016-07-09 10:57 GMT+08:00 Yu-Chieh <jay0607 at gmail.com>:
> i have checked firmware firmware-5.bin_10.4.3.00063-1 on codeaurora
>
> regarding ram mode, i think it's not supported
> <6>[232109.383248] ath10k_pci 0003:01:00.0: firmware ver 10.4.3.00063
> api 5 features no-p2p,peer-flow-ctrl crc32 a0d385ce
> <6>[232110.836979] ath10k_pci 0003:01:00.0: board_file api 1 bmi_id
> 1:1 crc32 77b2338a
> <4>[232113.369117] ath10k_pci 0003:01:00.0: 10.4 wmi init: vdevs: 16
> peers: 528  tid: 132
> <4>[232113.376857] ath10k_pci 0003:01:00.0: msdu-desc: 1424  skid: 32
> <6>[232113.452238] ath10k_pci 0003:01:00.0: htt-ver 2.2 wmi-op 6
> htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1
>
> regarding wmi_service, i have checked
> /sys/kernel/debug/ieee80211/phy0/ath10k/wmi_services
> WMI_SERVICE_MESH_11S                     -
> WMI_SERVICE_MESH_NON_11S                 enabled
>
> Any one knows MESH_NON_11S ?
>
> Jay
>
> 2016-07-09 1:48 GMT+08:00 Peter Oh <poh at codeaurora.org>:
>>
>> On 07/08/2016 10:15 AM, Yeoh Chun-Yeow wrote:
>>>
>>> Make sure the firmware has the raw mode feature bit enabled to support
>>> mesh.
>>
>> In addition to that, you may check out wmi_services (cat
>> /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services) if
>> WMI_SERVICE_MESH_11S is set to enabled which means 11s mesh supported in
>> native Wi-Fi mode.
>>
>>> ---
>>> Chun-Yeow
>>>
>>> On Fri, Jul 8, 2016 at 12:52 PM, Yu-Chieh <jay0607 at gmail.com> wrote:
>>>>
>>>> Hi,
>>>>
>>>> Does anyone know if current firmware support mesh mode(802.11s) on 99x0?
>>>>
>>>> Best regards,
>>>>
>>>> Jay
>>>>
>>>> _______________________________________________
>>>> ath10k mailing list
>>>> ath10k at lists.infradead.org
>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>
>>>
>> Peter