[RFC v2 05/11] ath10k: htc: refactorization

[Valo, Kalle]

Michal Kazior <michal.kazior at tieto.com> writes:

> On 13 December 2016 at 14:44, Valo, Kalle <kvalo at qca.qualcomm.com> wrote:
>> Erik Stromdahl <erik.stromdahl at gmail.com> writes:
>>
>>> Code refactorization:
>>>
>>> Moved the code for ep 0 in ath10k_htc_rx_completion_handler
>>> to ath10k_htc_control_rx_complete.
>>>
>>> This eases the implementation of SDIO/mbox significantly since
>>> the ep_rx_complete cb is invoked directly from the SDIO/mbox
>>> hif layer.
>>>
>>> Since the ath10k_htc_control_rx_complete already is present
>>> (only containing a warning message) there is no reason for not
>>> using it (instead of having a special case for ep 0 in
>>> ath10k_htc_rx_completion_handler).
>>>
>>> Signed-off-by: Erik Stromdahl <erik.stromdahl at gmail.com>
>>
>> I tested this on QCA988X PCI board just to see if there are any
>> regressions. It crashes immediately during module load, every time, and
>> bisected that the crashing starts on this patch:
>>
>> [ 1239.715325] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
>> [ 1239.885125] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
>> [ 1239.885260] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
>> [ 1239.885687] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
>> [ 1239.885699] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
>> [ 1239.885899] ath10k_pci 0000:02:00.0: firmware ver 10.2.4.70.59-2 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 4159f498
>> [ 1239.941836] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
>> [ 1239.941993] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
>> [ 1241.136693] BUG: unable to handle kernel NULL pointer dereference at   (null)
>> [ 1241.136738] IP: [<  (null)>]   (null)
>> [ 1241.136759] *pdpt = 0000000000000000 *pde = f0002a55f0002a55 [ 1241.136781]
>> [ 1241.136793] Oops: 0010 [#1] SMP
>>
>> What's odd is that when I added some printks on my own and enabled both
>> boot and htc debug levels it doesn't crash anymore. After everything
>> works normally after that, I can start AP mode and connect to it. Is it
>> a race somewhere?
>
> Yes. htc_wait_target() is called after hif_start(). The ep_rx_complete
> is set in htc_wait_target() [changed patch 4, but still too late].
>
> ep_rx_complete must be set prior to calling hif_start(). You probably
> crash on end of ath10k_htc_rx_completion_handler() when trying to call
> ep->ep_ops.ep_rx_complete(ar, skb).

Yeah, just checked and ep->ep_ops.ep_rx_complete is NULL at the end of
ath10k_htc_rx_completion_handler().

-- 
Kalle Valo