ath10k firmware crashes in mesh mode on QCA9880
Benjamin Morgan
bmorgan at cococorp.com
Tue Dec 6 13:32:43 PST 2016
1. Yes, this appears to happens every time a unicast packet with
wpa_supplicant encryption in VHT80 mode is received. I haven't seen a
successful ping-pong pair.
2. We tried with 10.2.4.70.42-2 firmware and still saw crashes.
3. We ran our experiment again with extra debugging turned on.
Node A: 18:A6:F7:23:6E:66 | 10.230.5.41
Node B: 18:A6:F7:26:0F:21 | 10.230.5.42
The ping command we used was run on Node A was 'ping -s 1500 -i 0.1
10.230.5.42'
Here is the dmesg log from Node B.
[ 5413.478170] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5413.503954] ath10k_pci 0000:01:00.0: scan event bss channel type 4
reason 3 freq 5825 req_id 40961 scan_id 40960 vdev_id 0 state running (2)
[ 5413.503985] ath10k_pci 0000:01:00.0: chan info err_code 0 freq 5825
cmd_flags 1 noise_floor -105 rx_clear_count 7692807 cycle_count 312271423
[ 5413.504029] ath10k_pci 0000:01:00.0: scan event completed type 2
reason 0 freq 5825 req_id 40961 scan_id 40960 vdev_id 0 state running (2)
[ 5413.525868] ath10k_pci 0000:01:00.0: wmi vdev install key idx 1
cipher 4 len 16
[ 5413.526014] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 31 value 1
[ 5413.526193] ath10k_pci 0000:01:00.0: mac vdev 0 set keyidx 1
[ 5413.526216] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 31 value 1
[ 5413.526532] ath10k_pci 0000:01:00.0: mac chanctx add freq 5180 width
3 ptr 86db29b0
[ 5413.526556] ath10k_pci 0000:01:00.0: mac monitor recalc started? 0
needed? 0 allowed? 1
[ 5413.526574] ath10k_pci 0000:01:00.0: mac chanctx assign ptr 86db29b0
vdev_id 0
[ 5413.526592] ath10k_pci 0000:01:00.0: mac vdev 0 start center_freq
5180 phymode 11ac-vht80
[ 5413.526616] ath10k_pci 0000:01:00.0: wmi vdev start id 0x0 flags:
0x0, freq 5180, mode 10, ch_flags: 0xA000000, max_power: 46
[ 5413.533099] ath10k_pci 0000:01:00.0: WMI_VDEV_START_RESP_EVENTID
[ 5413.533148] ath10k_pci 0000:01:00.0: mac vdev_id 0 txpower 23
[ 5413.533163] ath10k_pci 0000:01:00.0: mac txpower 23
[ 5413.533180] ath10k_pci 0000:01:00.0: wmi pdev set param 3 value 46
[ 5413.533247] ath10k_pci 0000:01:00.0: wmi pdev set param 4 value 46
[ 5413.533295] ath10k_pci 0000:01:00.0: mac chanctx change freq 5180
width 3 ptr 86db29b0 changed 10
[ 5413.533318] ath10k_pci 0000:01:00.0: mac chanctx change freq 5180
width 3 ptr 86db29b0 changed 2
[ 5413.533337] ath10k_pci 0000:01:00.0: mac monitor recalc started? 0
needed? 1 allowed? 1
[ 5413.533357] ath10k_pci 0000:01:00.0: WMI vdev create: id 1 type 4
subtype 0 macaddr 18:a6:f7:26:0f:21
[ 5413.533412] ath10k_pci 0000:01:00.0: mac monitor vdev 1 created
[ 5413.533463] ath10k_pci 0000:01:00.0: wmi vdev start id 0x1 flags:
0x0, freq 5180, mode 10, ch_flags: 0xA000000, max_power: 46
[ 5413.937652] ath10k_pci 0000:01:00.0: wmi event debug mesg len 152
[ 5413.978273] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5414.478363] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5414.527015] ath10k_pci 0000:01:00.0: WMI_VDEV_START_RESP_EVENTID
[ 5414.527067] ath10k_pci 0000:01:00.0: wmi mgmt vdev up id 0x1 assoc id
0 bssid 18:a6:f7:26:0f:21
[ 5414.527121] ath10k_pci 0000:01:00.0: mac monitor vdev 1 started
[ 5414.527165] ath10k_pci 0000:01:00.0: mac monitor started
[ 5414.527216] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 3
value 1000
[ 5414.527262] ath10k_pci 0000:01:00.0: mac vdev 0 beacon_interval 1000
[ 5414.527278] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 5414.527294] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 5414.527314] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 5414.527330] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 5414.527457] ath10k_pci 0000:01:00.0: wmi mgmt vdev up id 0x0 assoc id
0 bssid 00:00:00:00:00:00
[ 5414.527501] ath10k_pci 0000:01:00.0: mac vdev 0 up
[ 5414.527564] ath10k_pci 0000:01:00.0: WMI_TBTTOFFSET_UPDATE_EVENTID
[ 5414.541090] ath10k_pci 0000:01:00.0: mac monitor recalc started? 1
needed? 1 allowed? 1
[ 5414.978454] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5415.478548] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5415.978649] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5416.445280] ath10k_pci 0000:01:00.0: mac monitor recalc started? 1
needed? 1 allowed? 1
[ 5416.478761] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5416.978879] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5417.478985] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5417.979081] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5418.479190] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5418.979301] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5419.479403] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5419.979551] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5420.479643] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5420.979746] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5421.479841] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5421.979940] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5422.480288] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5422.980386] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5423.480490] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5423.980600] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5424.480702] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5424.971969] ath10k_pci 0000:01:00.0: mac vdev 0 peer create
18:a6:f7:23:6e:66 (new sta) sta 1 / 128 peer 2 / 144
[ 5424.972000] ath10k_pci 0000:01:00.0: wmi peer create vdev_id 0
peer_addr 18:a6:f7:23:6e:66
[ 5424.975107] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 5424.975134] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 5424.975219] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 5424.975238] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 5424.980787] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5425.204468] ath10k_pci 0000:01:00.0: mac sta 18:a6:f7:23:6e:66 associated
[ 5425.204531] ath10k_pci 0000:01:00.0: mac ht peer 18:a6:f7:23:6e:66
mcs cnt 24 nss 3
[ 5425.204548] ath10k_pci 0000:01:00.0: mac peer 18:a6:f7:23:6e:66 qos 1
[ 5425.204563] ath10k_pci 0000:01:00.0: mac peer 18:a6:f7:23:6e:66
phymode 11na-ht40
[ 5425.204585] ath10k_pci 0000:01:00.0: wmi peer assoc vdev 0 addr
18:a6:f7:23:6e:66 (new)
[ 5425.204614] ath10k_pci 0000:01:00.0: wmi vdev 0 peer
0x18:a6:f7:23:6e:66 set param 1 value 0
[ 5425.205376] ath10k_pci 0000:01:00.0: received event id 36891 not
implemented
[ 5425.209240] ath10k_pci 0000:01:00.0: wmi vdev install key idx 0
cipher 4 len 16
[ 5425.209655] ath10k_pci 0000:01:00.0: wmi vdev install key idx 1
cipher 4 len 16
[ 5425.209848] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 31 value 1
[ 5425.210196] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 5425.210221] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 5425.210296] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 5425.210315] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 5425.480863] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5425.938619] ath10k_pci 0000:01:00.0: wmi event debug mesg len 100
[ 5425.980946] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5425.995007] ath10k_pci 0000:01:00.0: mac sta rc update for
18:a6:f7:23:6e:66 changed 00000001 bw 2 nss 3 smps 1
[ 5425.995060] ath10k_pci 0000:01:00.0: mac update sta 18:a6:f7:23:6e:66
peer bw 2
[ 5425.995081] ath10k_pci 0000:01:00.0: wmi vdev 0 peer
0x18:a6:f7:23:6e:66 set param 4 value 2
[ 5426.481030] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5426.981117] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5427.481206] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5427.981294] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5428.481628] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5428.981718] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5429.481812] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5429.981894] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5430.481985] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5430.982073] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5431.482174] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5431.982505] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5432.482597] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5432.982679] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5433.482765] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5433.982857] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5434.482946] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5434.983008] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5435.483100] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5435.983181] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5436.483276] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5436.983366] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5437.483445] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5437.983516] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5438.483607] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5438.983692] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 5439.439875] ath10k_pci 0000:01:00.0: firmware crashed! (uuid
db76b67c-ca98-4519-a762-4ff4edb45526)
[ 5439.449007] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c
chip_id 0x043202ff sub 0000:0000
[ 5439.458378] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1
tracing 0 dfs 1 testmode 1
[ 5439.471460] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.70.54 api 5
features no-p2p,raw-mode,mfp crc32 9d340dd9
[ 5439.481844] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A
crc32 bebc7c08
[ 5439.489267] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2
cal file max-sta 128 raw 0 hwcrypto 1
[ 5439.500918] ath10k_pci 0000:01:00.0: firmware register dump:
[ 5439.506678] ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3
0x009A4577 0x00955B31
[ 5439.514706] ath10k_pci 0000:01:00.0: [04]: 0x009A4577 0x00060130
0x00000002 0x00439E98
[ 5439.522751] ath10k_pci 0000:01:00.0: [08]: 0x0044110C 0x00442074
0x00407120 0x004436CC
[ 5439.530794] ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000
0x009A3518 0x009A3526
[ 5439.538834] ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x0094085D
0x00000000 0x00000000
[ 5439.546871] ath10k_pci 0000:01:00.0: [20]: 0x409A4577 0x0040AAC4
0x0040AC60 0x0040AC09
[ 5439.554915] ath10k_pci 0000:01:00.0: [24]: 0x809A44BA 0x0040AB24
0x00400000 0xC09A4577
[ 5439.562948] ath10k_pci 0000:01:00.0: [28]: 0x809A39DE 0x0040AB84
0x0044110C 0x00442074
[ 5439.570992] ath10k_pci 0000:01:00.0: [32]: 0x809A5FE2 0x0040ABB4
0x0044110C 0x00407120
[ 5439.579032] ath10k_pci 0000:01:00.0: [36]: 0x809A2E6C 0x0040ABF4
0x0040AC14 0x00001580
[ 5439.587070] ath10k_pci 0000:01:00.0: [40]: 0x80990F6F 0x0040AD04
0x009C643C 0x004436CC
[ 5439.595113] ath10k_pci 0000:01:00.0: [44]: 0x80998510 0x0040AD64
0x004208FC 0x00439E4C
[ 5439.603146] ath10k_pci 0000:01:00.0: [48]: 0x8099AE95 0x0040AD84
0x004208FC 0x00425E00
[ 5439.611191] ath10k_pci 0000:01:00.0: [52]: 0x809BFC55 0x0040AEE4
0x00424FE8 0x00000002
[ 5439.619230] ath10k_pci 0000:01:00.0: [56]: 0x80940F18 0x0040AF14
0x00000004 0x004039D0
[ 5439.726818] ieee80211 phy0: Hardware restart was requested
[ 5439.732433] ath10k_pci 0000:01:00.0: wmi mgmt vdev down id 0x1
[ 5439.732461] ath10k_pci 0000:01:00.0: wmi vdev stop id 0x1
[ 5439.732482] ath10k_pci 0000:01:00.0: failed to synchronize monitor
vdev 1 stop: -143
[ 5439.740370] ath10k_pci 0000:01:00.0: mac monitor vdev 1 stopped
[ 5439.740386] ath10k_pci 0000:01:00.0: failed to stop monitor vdev: -143
[ 5439.747042] ath10k_pci 0000:01:00.0: wmi disable pktlog
We noticed in this log that when the radio starts up it says that it is
in VHT80 mode:
[ 5413.526592] ath10k_pci 0000:01:00.0: mac vdev 0 start center_freq
5180 phymode 11ac-vht80
But when a peer connects it seems to think the peer is in HT40 mode:
[ 5425.204563] ath10k_pci 0000:01:00.0: mac peer 18:a6:f7:23:6e:66
phymode 11na-ht40
Compared to no encryption case - this log was taken from Node A:
[ 24.874253] ath10k_pci 0000:01:00.0: mac chanctx add freq 5180 width
3 ptr 86d26db0
[ 24.874278] ath10k_pci 0000:01:00.0: mac monitor recalc started? 0
needed? 0 allowed? 1
[ 24.874296] ath10k_pci 0000:01:00.0: mac chanctx assign ptr 86d26db0
vdev_id 0
[ 24.874312] ath10k_pci 0000:01:00.0: mac vdev 0 start center_freq
5180 phymode 11ac-vht80
[ 24.874337] ath10k_pci 0000:01:00.0: wmi vdev start id 0x0 flags:
0x0, freq 5180, mode 10, ch_flags: 0xA000000, max_power: 46
[ 24.881335] ath10k_pci 0000:01:00.0: WMI_VDEV_START_RESP_EVENTID
[ 24.881423] ath10k_pci 0000:01:00.0: mac vdev_id 0 txpower 23
[ 24.881438] ath10k_pci 0000:01:00.0: mac txpower 23
[ 24.881454] ath10k_pci 0000:01:00.0: wmi pdev set param 3 value 46
[ 24.881491] ath10k_pci 0000:01:00.0: wmi pdev set param 4 value 46
[ 24.881515] ath10k_pci 0000:01:00.0: mac chanctx change freq 5180
width 3 ptr 86d26db0 changed 10
[ 24.881535] ath10k_pci 0000:01:00.0: mac chanctx change freq 5180
width 3 ptr 86d26db0 changed 2
[ 24.881554] ath10k_pci 0000:01:00.0: mac monitor recalc started? 0
needed? 1 allowed? 1
[ 24.881574] ath10k_pci 0000:01:00.0: WMI vdev create: id 1 type 4
subtype 0 macaddr 18:a6:f7:23:6e:66
[ 24.881689] ath10k_pci 0000:01:00.0: mac monitor vdev 1 created
[ 24.881745] ath10k_pci 0000:01:00.0: wmi vdev start id 0x1 flags:
0x0, freq 5180, mode 10, ch_flags: 0xA000000, max_power: 46
[ 25.273460] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 25.730570] ath10k_pci 0000:01:00.0: wmi event debug mesg len 300
[ 25.773566] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 25.874556] ath10k_pci 0000:01:00.0: WMI_VDEV_START_RESP_EVENTID
[ 25.879992] ath10k_pci 0000:01:00.0: wmi mgmt vdev up id 0x1 assoc id
0 bssid 18:a6:f7:23:6e:66
[ 25.880077] ath10k_pci 0000:01:00.0: mac monitor vdev 1 started
[ 25.880093] ath10k_pci 0000:01:00.0: mac monitor started
[ 25.880139] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 3
value 1000
[ 25.880184] ath10k_pci 0000:01:00.0: mac vdev 0 beacon_interval 1000
[ 25.880199] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 25.880215] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 25.880235] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 25.880250] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 25.880988] ath10k_pci 0000:01:00.0: wmi mgmt vdev up id 0x0 assoc id
0 bssid 00:00:00:00:00:00
[ 25.881035] ath10k_pci 0000:01:00.0: mac vdev 0 up
[ 25.881097] ath10k_pci 0000:01:00.0: WMI_TBTTOFFSET_UPDATE_EVENTID
[ 25.882968] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 25.928796] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 25.928821] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 25.928866] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 25.928883] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 25.929020] ath10k_pci 0000:01:00.0: mac monitor recalc started? 1
needed? 1 allowed? 1
[ 25.941886] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 25.941911] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 25.941955] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 25.941972] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 25.953727] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 25.953753] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 25.953798] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 25.953817] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 25.970588] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 25.970614] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 25.970659] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 25.970676] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 25.989056] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 25.989081] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 25.989126] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 25.989143] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 26.071686] ath10k_pci 0000:01:00.0: mac vdev 0 peer create
18:a6:f7:26:0f:21 (new sta) sta 1 / 128 peer 2 / 144
[ 26.071712] ath10k_pci 0000:01:00.0: wmi peer create vdev_id 0
peer_addr 18:a6:f7:26:0f:21
[ 26.071952] ath10k_pci 0000:01:00.0: mac sta 18:a6:f7:26:0f:21 associated
[ 26.071981] ath10k_pci 0000:01:00.0: mac ht peer 18:a6:f7:26:0f:21
mcs cnt 24 nss 3
[ 26.071999] ath10k_pci 0000:01:00.0: mac vht peer 18:a6:f7:26:0f:21
max_mpdu 1048575 flags 0x601b001
[ 26.072013] ath10k_pci 0000:01:00.0: mac peer 18:a6:f7:26:0f:21 qos 1
[ 26.072028] ath10k_pci 0000:01:00.0: mac peer 18:a6:f7:26:0f:21
phymode 11ac-vht80
[ 26.072047] ath10k_pci 0000:01:00.0: wmi peer assoc vdev 0 addr
18:a6:f7:26:0f:21 (new)
[ 26.072071] ath10k_pci 0000:01:00.0: wmi vdev 0 peer
0x18:a6:f7:26:0f:21 set param 1 value 0
[ 26.072502] ath10k_pci 0000:01:00.0: received event id 36891 not
implemented
[ 26.074194] ath10k_pci 0000:01:00.0: mac sta rc update for
18:a6:f7:26:0f:21 changed 00000000 bw 2 nss 3 smps 1
[ 26.074586] ath10k_pci 0000:01:00.0: vdev 0 set beacon tx mode to
staggered
[ 26.074609] ath10k_pci 0000:01:00.0: wmi pdev set param 7 value 0
[ 26.074682] ath10k_pci 0000:01:00.0: mac vdev 0 dtim_period 2
[ 26.074701] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 13 value 2
[ 26.074760] ath10k_pci 0000:01:00.0: mac vdev 0 slot_time 2
[ 26.074779] ath10k_pci 0000:01:00.0: wmi vdev id 0x0 set param 7 value 2
[ 26.273652] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 26.730650] ath10k_pci 0000:01:00.0: wmi event debug mesg len 44
[ 26.773733] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
[ 27.135445] ath10k_pci 0000:01:00.0: mac monitor recalc started? 1
needed? 1 allowed? 1
[ 27.273810] ath10k_pci 0000:01:00.0: WMI_UPDATE_STATS_EVENTID
It seems to start up in VHT80 mode and when it peers with Node B it
thinks Node B is also in VHT80 mode and ping works.
4. Beacons are sent at 6 Mb/s basic rate and unicast QoS Data is sent
with three spatial streams. Attached is the full pcap of the experiment.
Thank you for looking into this!
~Benjamin
On 12/05/2016 11:24 AM, Nagarajan, Ashok Raj wrote:
> 0x009A4577 0x00955B31
>
> Benjamin, Thanks for the logs.
> Quick questions to further debug the issue here,
>
> 1. Is this issue seen every time you start sending data traffic?
> 2. Issue seen with older firmwares? (FYR, http://linuxwireless.org/en/users/Drivers/ath10k/firmware/ )
> 3. Could you please share the dmesg from your device after enabling MAC and WMI logs in ath10k driver
> To enable debug logs please see http://linuxwireless.org/en/users/Drivers/ath10k/debug/
> 4. Do you know what is the Number of Spatial Streams seen in mesh beacons and in mesh data packet?
>
> Thanks,
> Ashok
-------------- next part --------------
A non-text attachment was scrubbed...
Name: ath10k_crash_pcap.tgz
Type: application/x-compressed-tar
Size: 25083 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/ath10k/attachments/20161206/23b00df7/attachment-0001.bin>
More information about the ath10k
mailing list