qca6164 support

[Anish Tondwalkar]

Update: firmware works and I have internet! Thanks everyone (especially Michal)!

On Mon, Aug 10, 2015 at 7:43 PM, Ben Greear <greearb at candelatech.com> wrote:
> On 08/10/2015 04:05 PM, Anish Tondwalkar wrote:
>> Got it working! Sort of! I asked vvanpo for his firmware, and with
>> that I can see the wireless device after I boot. But I still can't
>> connect to any networks or see them.
>>
>> Here's the firmware:
>> https://github.com/atondwal/ath10k-firmware/commit/88fca85ef59d708b9874e5b7885416b58aef9ee7
>>
>>
>> [   66.267355] ath10k_pci 0000:03:00.0: Direct firmware load for
>> ath10k/QCA6174/hw2.1/board-pci-168c:0041:17aa:3545.bin failed with
>> error -2
>> [   66.267358] ath10k_pci 0000:03:00.0: Falling back to user helper
>> [  126.315169] ath10k_pci 0000:03:00.0: failed to load spec board
>> file, falling back to generic: -11
>> [  126.349113] This the patched kernel -Anish
>> [  127.514569] ath10k_pci 0000:03:00.0: qca6174 hw2.1 (0x05010000,
>> 0x003405ff, 168c:0041:17aa:3545 fallback) fw atheros-12.0.0.102-fw api
>> 5 htt-ver 3.25 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
>> features
>> [  127.514574] ath10k_pci 0000:03:00.0: debug 0 debugfs 1 tracing 0
>> dfs 0 testmode 0
>> [  127.593699] ath: EEPROM regdomain: 0x6c
>> [  127.593702] ath: EEPROM indicates we should expect a direct regpair map
>> [  127.593703] ath: Country alpha2 being used: 00
>> [  127.593704] ath: Regpair used: 0x6c
>> [  127.605414] ath10k_pci 0000:03:00.0 wlp3s0: renamed from wlan0
>>
>> ~ ❯❯❯ sudo iwconfig wlp3s0 essid wahoo ap any
>> ~ ❯❯❯ sudo iwconfig wlp3s0
>> wlp3s0    IEEE 802.11abgn  ESSID:"wahoo"
>>           Mode:Managed  Access Point: Not-Associated   Tx-Power=off
>>           Retry short limit:7   RTS thr:off   Fragment thr:off
>>           Encryption key:off
>>           Power Management:off
>>
>> ~ ❯❯❯ sudo iwconfig wlp3s0 essid wahoo ap any
>> ~ ❯❯❯ sudo dhcpcd wlp3s0
>> wlp3s0: adding address fe80::1851:cd3e:2790:ed4f
>> wlp3s0: starting wpa_supplicant
>> wlp3s0: failed to start wpa_supplicant
>> wlp3s0: Successfully initialized wpa_supplicant
>> Line 1182: unknown EAP method 'SIM'
>> You may need to add support for this EAP method during wpa_supplicant
>> build time configuration.
>> See README for more information.
>> Line 1182: failed to parse eap 'SIM'.
>> Line 1185: failed to parse network block.
>> Line 1192: unknown EAP method 'PSK'
>> You may need to add support for this EAP method during wpa_supplicant
>> build time configuration.
>> See README for more information.
>> Line 1192: failed to parse eap 'PSK'.
>> Line 1196: failed to parse network block.
>> Line 1228: unknown EAP method 'IKEV2'
>> You may need to add support for this EAP method during wpa_supplicant
>> build time configuration.
>> See README for more information.
>> Line 1228: failed to parse eap 'IKEV2'.
>> Line 1231: failed to parse network block.
>> Failed to read or parse configuration '/etc/wpa_supplicant/wpa_supplicant.conf'.
>
> You have a bad supplicant config file.  This is not directly related to any
> problems you might be having with the firmware.
>
> Thanks,
> Ben
>
> --
> Ben Greear <greearb at candelatech.com>
> Candela Technologies Inc  http://www.candelatech.com
>



-- 
Anish

Q: Why is this email two sentences or less?
A: http://two.sentenc.es