Comfast CF-E110n
Bill Moffitt
bmoffitt at ayrstone.com
Wed Oct 25 13:37:27 PDT 2023
Roger-
Good idea. I think I may have been running firmware for a different
device (E-320N, probably - it appears to have been the base design for
several of their products).
I was hoping you (or someone) could look at the log and say, "Hey, I
know what that is..."
Worth a shot...
Next step - pull up one of the ones with the old firmware and compare
settings with the .dts file (and figure out exactly what they're
running).
Thanks,
Bill
On Tue, Oct 24, 2023 at 2:32 PM Roger Pueyo Centelles | Guifi.net
<roger.pueyo at guifi.net> wrote:
>
> Hi, Bill,
>
> I have a couple of them, but they're in a remote location I can't access
> right now. However, on one of them, I recently upgraded from OpenWrt
> 22.03.X to 23.05.0 and I did not experience such issues.
>
> In order to narrow down the issue, you may want to try flashing this
> older OpenWrt version (which one was it? CF-E110N is supported since
> 19.07...), then upgrade one major release at a time (first 21.02, then
> 22.03, until 23.05). When does this issue appear, if it does?
>
> Best,
>
> Roger
>
> El 23/10/23 a les 23:54, Bill Moffitt ha escrit:
> > I have been using an older version of OpenWRT on my E110Ns; I loaded up
> > the latest release to see if it would fix some "LOST BEACON" problems.
> >
> > Unfortunately, it didn't even boot (went into a bootloop), so I broke
> > out the serial cable,
> > busted open the radio, and connected it. Here's what I captured:
> >
> > <code>
> > U-Boot 1.1.4-ge619c187-dirty (Apr 12 2017 - 18:52:08)
> >
> > ap143 - Honey Bee 2.0
> >
> > DRAM: 64 MB
> > Flash: 16 MB
> >
> > dup 1 speed 100
> > Using eth0 device
> > ping failed; host 192.168.1.10 is not alive
> > Unknown command 'ERROR!' - try 'help'
> > Hit any key to stop autoboot: 1 0
> > ## Booting image at 9f020000 ...
> > Image Name: MIPS OpenWrt Linux-5.15.134
> > Created: 2023-10-09 21:45:35 UTC
> > Image Type: MIPS Linux Kernel Image (lzma compressed)
> > Data Size: 2328775 Bytes = 2.2 MB
> > Load Address: 80060000
> > Entry Point: 80060000
> > Verifying Checksum at 0x9f020040 ...OK
> > Uncompressing Kernel Image ... OK
> > No initrd
> > ## Transferring control to Linux (at address 80060000) ...
> > ## Giving linux memsize in bytes, 67108864
> >
> > Starting kernel ...
> >
> > [ 0.000000] Linux version 5.15.134 (builder at buildhost)
> > (mips-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23497-6637af95aa)
> > 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Mon Oct 9 21:45:35 2023
> > [ 0.000000] printk: bootconsole [early0] enabled
> > [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
> > [ 0.000000] MIPS: machine is COMFAST CF-E110N v2
> > [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
> > [ 0.000000] Initrd not found or empty - disabling initrd
> > [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> > [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
> > linesize 32 bytes
> > [ 0.000000] Zone ranges:
> > [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
> > [ 0.000000] Movable zone start for each node
> > [ 0.000000] Early memory node ranges
> > [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
> > [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
> > [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
> > [ 0.000000] Kernel command line: console=ttyS0,115200n8
> > rootfstype=squashfs,jffs2
> > [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768
> > bytes, linear)
> > [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384
> > bytes, linear)
> > [ 0.000000] Writing ErrCtl register=00000000
> > [ 0.000000] Readback ErrCtl register=00000000
> > [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> > [ 0.000000] Memory: 55972K/65536K available (6077K kernel code,
> > 591K rwdata, 780K rodata, 1184K init, 217K bss, 9564K reserved, 0K
> > cma-reserved)
> > [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> > [ 0.000000] NR_IRQS: 51
> > [ 0.000000] CPU clock: 650.000 MHz
> > [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles:
> > 0xffffffff, max_idle_ns: 5880801374 ns
> > [ 0.000002] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps
> > every 6607641598ns
> > [ 0.008370] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
> > [ 0.074950] pid_max: default: 32768 minimum: 301
> > [ 0.080919] Mount-cache hash table entries: 1024 (order: 0, 4096
> > bytes, linear)
> > [ 0.088644] Mountpoint-cache hash table entries: 1024 (order: 0,
> > 4096 bytes, linear)
> > [ 0.105660] clocksource: jiffies: mask: 0xffffffff max_cycles:
> > 0xffffffff, max_idle_ns: 19112604462750000 ns
> > [ 0.116125] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
> > [ 0.123566] pinctrl core: initialized pinctrl subsystem
> > [ 0.131441] NET: Registered PF_NETLINK/PF_ROUTE protocol family
> > [ 0.138492] thermal_sys: Registered thermal governor 'step_wise'
> > [ 0.153766] clocksource: Switched to clocksource MIPS
> > [ 0.167301] NET: Registered PF_INET protocol family
> > [ 0.172759] IP idents hash table entries: 2048 (order: 2, 16384
> > bytes, linear)
> > [ 0.181676] tcp_listen_portaddr_hash hash table entries: 512
> > (order: 0, 4096 bytes, linear)
> > [ 0.190630] Table-perturb hash table entries: 65536 (order: 6,
> > 262144 bytes, linear)
> > [ 0.198823] TCP established hash table entries: 1024 (order: 0,
> > 4096 bytes, linear)
> > [ 0.206939] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
> > [ 0.214408] TCP: Hash tables configured (established 1024 bind 1024)
> > [ 0.221345] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
> > [ 0.228344] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
> > [ 0.236302] NET: Registered PF_UNIX/PF_LOCAL protocol family
> > [ 0.242338] PCI: CLS 0 bytes, default 32
> > [ 0.251473] workingset: timestamp_bits=14 max_order=14 bucket_order=0
> > [ 0.264981] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> > [ 0.271158] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
> > (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
> > [ 0.283297] Block layer SCSI generic (bsg) driver version 0.4
> > loaded (major 251)
> > [ 0.296681] pinctrl-single 1804002c.pinmux: 576 pins, size 72
> > [ 0.304425] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
> > [ 0.314714] printk: console [ttyS0] disabled
> > [ 0.319327] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9,
> > base_baud = 1562500) is a 16550A
> > [ 0.328537] printk: console [ttyS0] enabled
> > [ 0.328537] printk: console [ttyS0] enabled
> > [ 0.337608] printk: bootconsole [early0] disabled
> > [ 0.337608] printk: bootconsole [early0] disabled
> > [ 0.373725] spi-nor spi0.0: w25q128 (16384 Kbytes)
> > [ 0.378894] 4 fixed-partitions partitions found on MTD device spi0.0
> > [ 0.385536] OF: Bad cell count for /ahb/spi at 1f000000/flash at 0/partitions
> > [ 0.392416] OF: Bad cell count for /ahb/spi at 1f000000/flash at 0/partitions
> > [ 0.400124] OF: Bad cell count for /ahb/spi at 1f000000/flash at 0/partitions
> > [ 0.407094] OF: Bad cell count for /ahb/spi at 1f000000/flash at 0/partitions
> > [ 0.414211] Creating 4 MTD partitions on "spi0.0":
> > [ 0.419186] 0x000000000000-0x000000010000 : "u-boot"
> > [ 0.432380] 0x000000010000-0x000000020000 : "art"
> > [ 0.438974] 0x000000020000-0x000000ff0000 : "firmware"
> > [ 0.448501] 2 uimage-fw partitions found on MTD device firmware
> > [ 0.454736] Creating 2 MTD partitions on "firmware":
> > [ 0.459874] 0x000000000000-0x000000240000 : "kernel"
> > [ 0.466527] 0x000000240000-0x000000fd0000 : "rootfs"
> > [ 0.475397] mtd: setting mtd4 (rootfs) as root device
> > [ 0.480780] 1 squashfs-split partitions found on MTD device rootfs
> > [ 0.487281] 0x0000005b0000-0x000000fd0000 : "rootfs_data"
> > [ 0.495748] 0x000000ff0000-0x000001000000 : "nvram"
> > [ 0.914866] ag71xx 19000000.eth: Could not connect to PHY device.
> > Deferring probe.
> > </code>
> > (reboot)
> >
> > Is anyone else using the CF-110N?
> >
> > -Bill
> >
> > _______________________________________________
> > openwrt-devel mailing list
> > openwrt-devel at lists.openwrt.org
> > https://lists.openwrt.org/mailman/listinfo/openwrt-devel
> >
>
More information about the openwrt-devel
mailing list