[PATCH V11 4/6] ARM: dts: bcm283x: Add CPU thermal zone with 1 trip point

[Stefan Wahren]

As suggested by Eduardo Valentin this adds the thermal zone for
the bcm2835 SoC with its single thermal sensor. We start with
the criticial trip point and leave the cooling devices empty
since we don't have any at the moment. Since the coefficients
could vary depending on the SoC we need to define them separate.

Signed-off-by: Stefan Wahren <stefan.wahren at i2se.com>
---
 arch/arm/boot/dts/bcm2835.dtsi |    4 ++++
 arch/arm/boot/dts/bcm2836.dtsi |    4 ++++
 arch/arm/boot/dts/bcm283x.dtsi |   21 +++++++++++++++++++++
 3 files changed, 29 insertions(+)

diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi
index 0890d97..659b6e9 100644
--- a/arch/arm/boot/dts/bcm2835.dtsi
+++ b/arch/arm/boot/dts/bcm2835.dtsi
@@ -24,6 +24,10 @@
 	};
 };
 
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
 /* enable thermal sensor with the correct compatible property set */
 &thermal {
 	compatible = "brcm,bcm2835-thermal";
diff --git a/arch/arm/boot/dts/bcm2836.dtsi b/arch/arm/boot/dts/bcm2836.dtsi
index 519a44f..da3deeb 100644
--- a/arch/arm/boot/dts/bcm2836.dtsi
+++ b/arch/arm/boot/dts/bcm2836.dtsi
@@ -77,6 +77,10 @@
 	interrupts = <8>;
 };
 
+&cpu_thermal {
+	coefficients = <(-538)	407000>;
+};
+
 /* enable thermal sensor with the correct compatible property set */
 &thermal {
 	compatible = "brcm,bcm2836-thermal";
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index a3106aa..9bc0a1c9 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -19,6 +19,26 @@
 		bootargs = "earlyprintk console=ttyAMA0";
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu-crit {
+					temperature	= <80000>;
+					hysteresis	= <0>;
+					type		= "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -394,6 +414,7 @@
 			compatible = "brcm,bcm2835-thermal";
 			reg = <0x7e212000 0x8>;
 			clocks = <&clocks BCM2835_CLOCK_TSENS>;
+			#thermal-sensor-cells = <0>;
 			status = "disabled";
 		};
 
-- 
1.7.9.5