[PATCH v3 2/4] arm64: dts: rockchip: Add SOQuartz blade board

Wed Nov 16 03:53:35 PST 2022

From: Andrew Powers-Holmes <aholmes at omnom.net>

This adds a device tree for the PINE64 SOQuartz blade baseboard,
a 1U rack mountable baseboard for the CM4 form factor with PoE
support designed for the SOQuartz CM4 System-on-Module.

The board takes power from either PoE or a 5V DC input, and allows
for mounting an M.2 SSD.

The board also features one USB 2.0 host port, one HDMI output,
a 3.5mm jack for UART, and the aforementioned gigabit networking
port.

Signed-off-by: Andrew Powers-Holmes <aholmes at omnom.net>
[rebase, squash, reword, misc fixes]
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas at gmail.com>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3566-soquartz-blade.dts    | 194 ++++++++++++++++++
 2 files changed, 195 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-soquartz-blade.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 832613143030..528a02b11552 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -71,6 +71,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-b.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-roc-pc.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-blade.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-cm4.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-box-demo.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bpi-r2-pro.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-soquartz-blade.dts b/arch/arm64/boot/dts/rockchip/rk3566-soquartz-blade.dts
new file mode 100644
index 000000000000..4e49bebf548b
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-soquartz-blade.dts
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+	model = "PINE64 RK3566 SOQuartz on Blade carrier board";
+	compatible = "pine64,soquartz-blade", "pine64,soquartz", "rockchip,rk3566";
+
+	/* labeled VCC3V0_SD in schematic to not conflict with PMIC regulator */
+	vcc3v0_sd: vcc3v0-sd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v0_sd";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	/* labeled VCC_SSD in schematic */
+	vcc3v3_pcie_p: vcc3v3-pcie-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie_p";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vbus>;
+	};
+
+	vcc5v_dcin: vcc5v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&combphy2 {
+	phy-supply = <&vcc3v3_sys>;
+	status = "okay";
+};
+
+&gmac1 {
+	status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+	status = "okay";
+
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+	status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+	status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6  - i2s1_sdi2_m1
+ * pin 40 - GPIO9  - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3  - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+	status = "disabled";
+};
+
+&led_diy {
+	color = <LED_COLOR_ID_RED>;
+	function = LED_FUNCTION_DISK_ACTIVITY;
+	linux,default-trigger = "disk-activity";
+	status = "okay";
+};
+
+&led_work {
+	color = <LED_COLOR_ID_GREEN>;
+	function = LED_FUNCTION_STATUS;
+	linux,default-trigger = "heartbeat";
+	status = "okay";
+};
+
+&pcie2x1 {
+	vpcie3v3-supply = <&vcc3v3_pcie_p>;
+	status = "okay";
+};
+
+&rgmii_phy1 {
+	status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+	status = "disabled";
+};
+
+&sdmmc0 {
+	vmmc-supply = <&vcc3v0_sd>;
+	status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7  - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8  - spi3_cs0_m0
+ * pin 40 - GPIO9  - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+	status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+	status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vbus>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	status = "okay";
+};
+
+&vbus {
+	vin-supply = <&vcc5v_dcin>;
+};
-- 
2.38.1


