Aw: Re: [PATCH v2 2/2] arm64: dts: rockchip: Add Bananapi R2 Pro

[Frank Wunderlich]

Hi

> Gesendet: Montag, 24. Januar 2022 um 09:31 Uhr
> Von: "Sascha Hauer" <sha at pengutronix.de>
> An: "Frank Wunderlich" <linux at fw-web.de>
> Cc: linux-rockchip at lists.infradead.org, "Frank Wunderlich" <frank-w at public-files.de>, "Rob Herring" <robh+dt at kernel.org>, "Heiko Stuebner" <heiko at sntech.de>, "Peter Geis" <pgwipeout at gmail.com>, "Johan Jonker" <jbx6244 at gmail.com>, devicetree at vger.kernel.org, linux-arm-kernel at lists.infradead.org, linux-kernel at vger.kernel.org
> Betreff: Re: [PATCH v2 2/2] arm64: dts: rockchip: Add Bananapi R2 Pro
>
> On Sun, Jan 23, 2022 at 02:51:16PM +0100, Frank Wunderlich wrote:
> > From: Frank Wunderlich <frank-w at public-files.de>
> >
> > This patch adds Devicetree for Bananapi R2 Pro based on RK3568.
> > Add uart/sd/emmc/i2c/rk809/tsadc nodes for basic function.
> > Gmac0 is directly connected to wan-port so usable without additional
> > driver.
> > On gmac1 there is a switch (rtl8367rb) connected which have not yet a
> > driver in mainline.
> >
> > Patch also prepares nodes for GPIO header.
> >
> > Co-developed-by: Peter Geis <pgwipeout at gmail.com>
> > Signed-off-by: Peter Geis <pgwipeout at gmail.com>
> > Signed-off-by: Frank Wunderlich <frank-w at public-files.de>
> > ---
> > +&gmac0 {
> > +	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
> > +	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
> > +	clock_in_out = "input";
> > +	phy-handle = <&rgmii_phy0>;
> > +	phy-mode = "rgmii";
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&gmac0_miim
> > +		     &gmac0_tx_bus2
> > +		     &gmac0_rx_bus2
> > +		     &gmac0_rgmii_clk
> > +		     &gmac0_rgmii_bus>;
> > +
> > +	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
> > +	snps,reset-active-low;
> > +	/* Reset time is 20ms, 100ms for rtl8211f */
>
> Is this really a rtl8211f? I don't know and it could indeed be a
> rtl8211f, I'm just asking because the comment is copy pasted from
> the Quartz64 board.

i know thats a RTL8211 phy, but i see no additional letter on the chip, based on shematics it's a RTL8211F-CG

> > +	snps,reset-delays-us = <0 20000 100000>;
> > +
> > +&mdio0 {
> > +	rgmii_phy0: ethernet-phy at 0 {
> > +		compatible = "ethernet-phy-ieee802.3-c22";
> > +		reg = <0x0>;
> > +	};
>
> 0 is the broadcast address. I'm not sure if it's a good idea to use it.
> There should be another address the phy listens on.

took this from the 3568-EVB (like the most parts, as the board is mostly the same), and in linux it's the same and working. The switch have also phy-id 0 on mdio bus #1, are you sure this is invalid?

regards Frank