[PATCH 7/9] riscv: dts: ultrarisc: add Rongda M0 board device tree

[Conor Dooley]

On Fri, May 15, 2026 at 09:18:03AM +0800, Jia Wang wrote:
> Rongda M0 is an mATX motherboard based on the UltraRISC DP1000 SoC.
> 
> Signed-off-by: Jia Wang <wangjia at ultrarisc.com>
> ---
>  arch/riscv/boot/dts/Makefile                       |   1 +
>  arch/riscv/boot/dts/ultrarisc/Makefile             |   2 +
>  .../dts/ultrarisc/dp1000-rongda-m0-pinctrl.dtsi    |  85 ++++++++++++++++
>  arch/riscv/boot/dts/ultrarisc/dp1000-rongda-m0.dts | 111 +++++++++++++++++++++
>  4 files changed, 199 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> index 69d8751fb17c..702882974251 100644
> --- a/arch/riscv/boot/dts/Makefile
> +++ b/arch/riscv/boot/dts/Makefile
> @@ -12,3 +12,4 @@ subdir-y += spacemit
>  subdir-y += starfive
>  subdir-y += tenstorrent
>  subdir-y += thead
> +subdir-y += ultrarisc
> diff --git a/arch/riscv/boot/dts/ultrarisc/Makefile b/arch/riscv/boot/dts/ultrarisc/Makefile
> new file mode 100644
> index 000000000000..d01a770d3cba
> --- /dev/null
> +++ b/arch/riscv/boot/dts/ultrarisc/Makefile
> @@ -0,0 +1,2 @@
> +# SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_ARCH_ULTRARISC) += dp1000-rongda-m0.dtb
> diff --git a/arch/riscv/boot/dts/ultrarisc/dp1000-rongda-m0-pinctrl.dtsi b/arch/riscv/boot/dts/ultrarisc/dp1000-rongda-m0-pinctrl.dtsi
> new file mode 100644
> index 000000000000..101b416b1079
> --- /dev/null
> +++ b/arch/riscv/boot/dts/ultrarisc/dp1000-rongda-m0-pinctrl.dtsi
> @@ -0,0 +1,85 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright(C) 2026 UltraRISC Technology (Shanghai) Co., Ltd.
> + */
> +
> +#include "dp1000.dtsi"
> +
> +&pmx0 {
> +	i2c0_pins: i2c0-pins {
> +		pins = "PA12", "PA13";
> +		function = "func0";

This is what I meant about func0 btw, and having this be "i2c" etc instead.
> diff --git a/arch/riscv/boot/dts/ultrarisc/dp1000-rongda-m0.dts b/arch/riscv/boot/dts/ultrarisc/dp1000-rongda-m0.dts
> new file mode 100644
> index 000000000000..6f72d60ad55e
> --- /dev/null
> +++ b/arch/riscv/boot/dts/ultrarisc/dp1000-rongda-m0.dts
> @@ -0,0 +1,111 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright(C) 2026 UltraRISC Technology (Shanghai) Co., Ltd.
> + */
> +
> +#include "dp1000-rongda-m0-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "Rongda M0 Board";
> +	compatible = "rongda,m0", "ultrarisc,dp1000";
> +
> +	aliases {
> +		serial0 = &uart0;
> +		serial1 = &uart1;
> +		serial2 = &uart2;
> +		serial3 = &uart3;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	gpio-poweroff {
> +		compatible = "gpio-poweroff";
> +		gpios = <&gpio_b 0 GPIO_ACTIVE_HIGH>;
> +		active-delay-ms = <100>;
> +
> +		status = "disabled";

Why bother adding the nodes if they are disabled? What enables them?

> +	};
> +
> +	gpio-restart {
> +		compatible = "gpio-restart";
> +		gpios = <&gpio_b 1 GPIO_ACTIVE_HIGH>;
> +		active-delay = <100>;
> +
> +		status = "disabled";
> +	};
> +};
> +
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0_pins>;
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins>;
> +};
> +
> +&i2c2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2_pins>;
> +
> +	rtc at 32 {
> +		compatible = "whwave,sd3078";
> +		reg = <0x32>;
> +	};
> +};
> +
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c3_pins>;
> +};
> +
> +&spi0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi0_pins>;
> +};
> +
> +&spi1 {
> +	num-cs = <1>;

Why is num-cs set at the board level here?

> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi1_pins>;
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins>;
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>;
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2_pins>;
> +};
> +
> +&ethernet {
> +	phy-handle = <&phy0>;
> +	/*
> +	 * YT8531 RGMII timing on this board requires no PHY internal delays.
> +	 * Using "rgmii-id" together with rx/tx-internal-delay-ps results in RX CRC
> +	 * errors and no usable traffic, so keep plain "rgmii" here.
> +	 */
> +	phy-mode = "rgmii";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		phy0: phy at 0 {
> +			reg = <0x00>;
> +		};
> +	};
> +};
> 
> -- 
> 2.34.1
> 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-riscv/attachments/20260515/0c4a7da6/attachment.sig>