[PATCH 2/2] riscv: dts: spacemit: Add MusePi Pro board device tree

[Yixun Lan]

Hi Troy,

On 12:16 Sun 28 Sep     , Troy Mitchell wrote:
> From: Troy Mitchell <troy.mitchell at linux.spacemit.com>
> 
> Add initial device tree support for the MusePi Pro board [1].
> The board is using the SpacemiT K1/M1 SoC.
> 
> The device tree is adapted from the SpacemiT vendor tree [2].
> 
> This minimal device tree enables booting into a serial console with UART
> output and a blinking LED.
> 
> Link:
> https://developer.spacemit.com/documentation?token=YJtdwnvvViPVcmkoPDpcvwfVnrh&type=pdf [1]
> https://gitee.com/bianbu-linux/linux-6.6/blob/k1-bl-v2.2.y/arch/riscv/boot/dts/spacemit/k1-x_MUSE-Pi-Pro.dts [2]
> 
same as patch 1
> Signed-off-by: Troy Mitchell <troy.mitchell at linux.spacemit.com>
> ---
>  arch/riscv/boot/dts/spacemit/Makefile          |  1 +
>  arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts | 40 ++++++++++++++++++++++++++
>  2 files changed, 41 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/Makefile b/arch/riscv/boot/dts/spacemit/Makefile
> index 152832644870624d8fd77684ef33addb42b0baf3..76b98096e2a46c3192651d6d66af7742f740c635 100644
> --- a/arch/riscv/boot/dts/spacemit/Makefile
> +++ b/arch/riscv/boot/dts/spacemit/Makefile
> @@ -2,3 +2,4 @@
>  dtb-$(CONFIG_ARCH_SPACEMIT) += k1-bananapi-f3.dtb
>  dtb-$(CONFIG_ARCH_SPACEMIT) += k1-milkv-jupiter.dtb
>  dtb-$(CONFIG_ARCH_SPACEMIT) += k1-orangepi-rv2.dtb
> +dtb-$(CONFIG_ARCH_SPACEMIT) += k1-musepi-pro.dtb
please sort

> diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
> new file mode 100644
> index 0000000000000000000000000000000000000000..3791186ce47b88887eab4321dcd7035668e7f02d
> --- /dev/null
> +++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
> @@ -0,0 +1,40 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2024 Yangyu Chen <cyy at cyyself.name>
> + * Copyright (C) 2025 Troy Mitchell <troy.mitchell at linux.spacemit.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "k1.dtsi"
> +#include "k1-pinctrl.dtsi"
> +
> +/ {
> +	model = "MusePi Pro";
this is a little bit short, how about make it "SpacemiT MusePi Pro"?

> +	compatible = "spacemit,musepi-pro", "spacemit,k1";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led1 {
> +			label = "sys-led";
> +			gpios = <&gpio K1_GPIO(96) GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +			default-state = "on";
> +		};
> +	};
> +};
> +
> +&uart0 {
..
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_2_cfg>;
swap these two lines, for similar reason, see my comment here
https://lore.kernel.org/all/20250918133209-GYB1273705@gentoo.org/

> +	status = "okay";
> +};
> 
> -- 
> 2.51.0
> 

while you are here, I'd suggest to push as many features as possible
instead of this minimal DT, which say - PMU, emmc, ethernet should be ready..
(ethernet is in next, should show up at v6.18-rc1)

-- 
Yixun Lan (dlan)