[PATCH net-next v12 4/5] riscv: dts: spacemit: Add Ethernet support for BPI-F3

[Vivian Wang]

Banana Pi BPI-F3 uses an RGMII PHY for each port and uses GPIO for PHY
reset.

Tested-by: Hendrik Hamerlinck <hendrik.hamerlinck at hammernet.be>
Signed-off-by: Vivian Wang <wangruikang at iscas.ac.cn>
Reviewed-by: Yixun Lan <dlan at gentoo.org>
Reviewed-by: Andrew Lunn <andrew at lunn.ch>
---
 arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts | 48 +++++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index fe22c747c5012fe56d42ac8a7efdbbdb694f31b6..33e223cefd4bd3a12fae176ac6cddd8276cb53dc 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -11,6 +11,8 @@ / {
 	compatible = "bananapi,bpi-f3", "spacemit,k1";
 
 	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
 		serial0 = &uart0;
 	};
 
@@ -40,6 +42,52 @@ &emmc {
 	status = "okay";
 };
 
+&eth0 {
+	phy-handle = <&rgmii0>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <0>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(110) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii0: phy at 1 {
+			reg = <0x1>;
+		};
+	};
+};
+
+&eth1 {
+	phy-handle = <&rgmii1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1_cfg>;
+	rx-internal-delay-ps = <0>;
+	tx-internal-delay-ps = <250>;
+	status = "okay";
+
+	mdio-bus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		reset-gpios = <&gpio K1_GPIO(115) GPIO_ACTIVE_LOW>;
+		reset-delay-us = <10000>;
+		reset-post-delay-us = <100000>;
+
+		rgmii1: phy at 1 {
+			reg = <0x1>;
+		};
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_2_cfg>;

-- 
2.50.1