[PATCH v3 08/11] riscv: dts: add initial SpacemiT K1 SoC device tree
Yixun Lan
dlan at gentoo.org
Thu Jul 4 23:38:39 PDT 2024
On 21:46 Thu 04 Jul , Jisheng Zhang wrote:
> On Wed, Jul 03, 2024 at 02:55:11PM +0000, Yixun Lan wrote:
> > From: Yangyu Chen <cyy at cyyself.name>
> >
> > Banana Pi BPI-F3 motherboard is powered by SpacemiT K1[1].
> >
> > Key features:
> > - 4 cores per cluster, 2 clusters on chip
> > - UART IP is Intel XScale UART
> >
> > Some key considerations:
> > - ISA string is inferred from vendor documentation[2]
> > - Cluster topology is inferred from datasheet[1] and L2 in vendor dts[3]
> > - No coherent DMA on this board
> > Inferred by taking vendor ethernet and MMC drivers to the mainline
> > kernel. Without dma-noncoherent in soc node, the driver fails.
> > - No cache nodes now
> > The parameters from vendor dts are likely to be wrong. It has 512
> > sets for a 32KiB L1 Cache. In this case, each set is 64B in size.
> > When the size of the cache line is 64B, it is a directly mapped
> > cache rather than a set-associative cache, the latter is commonly
> > used. Thus, I didn't use the parameters from vendor dts.
> >
> > Currently only support booting into console with only uart, other
> > features will be added soon later.
> >
> > Link: https://docs.banana-pi.org/en/BPI-F3/SpacemiT_K1_datasheet [1]
> > Link: https://developer.spacemit.com/#/documentation?token=BWbGwbx7liGW21kq9lucSA6Vnpb [2]
> > Link: https://gitee.com/bianbu-linux/linux-6.1/blob/bl-v1.0.y/arch/riscv/boot/dts/spacemit/k1-x.dtsi [3]
> > Signed-off-by: Yangyu Chen <cyy at cyyself.name>
> > Signed-off-by: Yixun Lan <dlan at gentoo.org>
> > ---
> > arch/riscv/boot/dts/spacemit/k1.dtsi | 376 +++++++++++++++++++++++++++++++++++
> > 1 file changed, 376 insertions(+)
> >
> > diff --git a/arch/riscv/boot/dts/spacemit/k1.dtsi b/arch/riscv/boot/dts/spacemit/k1.dtsi
> > new file mode 100644
> > index 0000000000000..a076e35855a2e
> > --- /dev/null
> > +++ b/arch/riscv/boot/dts/spacemit/k1.dtsi
> > @@ -0,0 +1,376 @@
> > +// SPDX-License-Identifier: GPL-2.0 OR MIT
> > +/*
> > + * Copyright (C) 2024 Yangyu Chen <cyy at cyyself.name>
> > + */
> > +
> > +/dts-v1/;
> > +/ {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + model = "SpacemiT K1";
> > + compatible = "spacemit,k1";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + serial1 = &uart2;
> > + serial2 = &uart3;
> > + serial3 = &uart4;
> > + serial4 = &uart5;
> > + serial5 = &uart6;
> > + serial6 = &uart7;
> > + serial7 = &uart8;
> > + serial8 = &uart9;
> > + };
> > +
> > + cpus {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + timebase-frequency = <24000000>;
> > +
> > + cpu-map {
> > + cluster0 {
> > + core0 {
> > + cpu = <&cpu_0>;
> > + };
> > + core1 {
> > + cpu = <&cpu_1>;
> > + };
> > + core2 {
> > + cpu = <&cpu_2>;
> > + };
> > + core3 {
> > + cpu = <&cpu_3>;
> > + };
> > + };
> > +
> > + cluster1 {
> > + core0 {
> > + cpu = <&cpu_4>;
> > + };
> > + core1 {
> > + cpu = <&cpu_5>;
> > + };
> > + core2 {
> > + cpu = <&cpu_6>;
> > + };
> > + core3 {
> > + cpu = <&cpu_7>;
> > + };
> > + };
> > + };
> > +
> > + cpu_0: cpu at 0 {
> > + compatible = "spacemit,x60", "riscv";
> > + device_type = "cpu";
> > + reg = <0>;
> > + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt";
> > + riscv,isa-base = "rv64i";
> > + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom",
> > + "zicbop", "zicboz", "zicntr", "zicond", "zicsr",
> > + "zifencei", "zihintpause", "zihpm", "zfh", "zba",
> > + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt",
> > + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt";
> > + riscv,cbom-block-size = <64>;
> > + riscv,cbop-block-size = <64>;
> > + riscv,cboz-block-size = <64>;
> > + mmu-type = "riscv,sv39";
> > +
> > + cpu0_intc: interrupt-controller {
> > + compatible = "riscv,cpu-intc";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > + };
> > +
> > + cpu_1: cpu at 1 {
> > + compatible = "spacemit,x60", "riscv";
> > + device_type = "cpu";
> > + reg = <1>;
> > + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt";
> > + riscv,isa-base = "rv64i";
> > + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom",
> > + "zicbop", "zicboz", "zicntr", "zicond", "zicsr",
> > + "zifencei", "zihintpause", "zihpm", "zfh", "zba",
> > + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt",
> > + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt";
> > + riscv,cbom-block-size = <64>;
> > + riscv,cbop-block-size = <64>;
> > + riscv,cboz-block-size = <64>;
> > + mmu-type = "riscv,sv39";
> > +
> > + cpu1_intc: interrupt-controller {
> > + compatible = "riscv,cpu-intc";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > + };
> > +
> > + cpu_2: cpu at 2 {
> > + compatible = "spacemit,x60", "riscv";
> > + device_type = "cpu";
> > + reg = <2>;
> > + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt";
> > + riscv,isa-base = "rv64i";
> > + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom",
> > + "zicbop", "zicboz", "zicntr", "zicond", "zicsr",
> > + "zifencei", "zihintpause", "zihpm", "zfh", "zba",
> > + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt",
> > + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt";
> > + riscv,cbom-block-size = <64>;
> > + riscv,cbop-block-size = <64>;
> > + riscv,cboz-block-size = <64>;
> > + mmu-type = "riscv,sv39";
> > +
> > + cpu2_intc: interrupt-controller {
> > + compatible = "riscv,cpu-intc";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > + };
> > +
> > + cpu_3: cpu at 3 {
> > + compatible = "spacemit,x60", "riscv";
> > + device_type = "cpu";
> > + reg = <3>;
> > + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt";
> > + riscv,isa-base = "rv64i";
> > + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom",
> > + "zicbop", "zicboz", "zicntr", "zicond", "zicsr",
> > + "zifencei", "zihintpause", "zihpm", "zfh", "zba",
> > + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt",
> > + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt";
> > + riscv,cbom-block-size = <64>;
> > + riscv,cbop-block-size = <64>;
> > + riscv,cboz-block-size = <64>;
> > + mmu-type = "riscv,sv39";
> > +
> > + cpu3_intc: interrupt-controller {
> > + compatible = "riscv,cpu-intc";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > + };
> > +
> > + cpu_4: cpu at 4 {
> > + compatible = "spacemit,x60", "riscv";
> > + device_type = "cpu";
> > + reg = <4>;
> > + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt";
> > + riscv,isa-base = "rv64i";
> > + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom",
> > + "zicbop", "zicboz", "zicntr", "zicond", "zicsr",
> > + "zifencei", "zihintpause", "zihpm", "zfh", "zba",
> > + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt",
> > + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt";
> > + riscv,cbom-block-size = <64>;
> > + riscv,cbop-block-size = <64>;
> > + riscv,cboz-block-size = <64>;
> > + mmu-type = "riscv,sv39";
> > +
> > + cpu4_intc: interrupt-controller {
> > + compatible = "riscv,cpu-intc";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > + };
> > +
> > + cpu_5: cpu at 5 {
> > + compatible = "spacemit,x60", "riscv";
> > + device_type = "cpu";
> > + reg = <5>;
> > + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt";
> > + riscv,isa-base = "rv64i";
> > + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom",
> > + "zicbop", "zicboz", "zicntr", "zicond", "zicsr",
> > + "zifencei", "zihintpause", "zihpm", "zfh", "zba",
> > + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt",
> > + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt";
> > + riscv,cbom-block-size = <64>;
> > + riscv,cbop-block-size = <64>;
> > + riscv,cboz-block-size = <64>;
> > + mmu-type = "riscv,sv39";
> > +
> > + cpu5_intc: interrupt-controller {
> > + compatible = "riscv,cpu-intc";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > + };
> > +
> > + cpu_6: cpu at 6 {
> > + compatible = "spacemit,x60", "riscv";
> > + device_type = "cpu";
> > + reg = <6>;
> > + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt";
> > + riscv,isa-base = "rv64i";
> > + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom",
> > + "zicbop", "zicboz", "zicntr", "zicond", "zicsr",
> > + "zifencei", "zihintpause", "zihpm", "zfh", "zba",
> > + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt",
> > + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt";
> > + riscv,cbom-block-size = <64>;
> > + riscv,cbop-block-size = <64>;
> > + riscv,cboz-block-size = <64>;
> > + mmu-type = "riscv,sv39";
> > +
> > + cpu6_intc: interrupt-controller {
> > + compatible = "riscv,cpu-intc";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > + };
> > +
> > + cpu_7: cpu at 7 {
> > + compatible = "spacemit,x60", "riscv";
> > + device_type = "cpu";
> > + reg = <7>;
> > + riscv,isa = "rv64imafdcv_zicbom_zicbop_zicboz_zicntr_zicond_zicsr_zifencei_zihintpause_zihpm_zfh_zba_zbb_zbc_zbs_zkt_zvfh_zvkt_sscofpmf_sstc_svinval_svnapot_svpbmt";
> > + riscv,isa-base = "rv64i";
> > + riscv,isa-extensions = "i", "m", "a", "f", "d", "c", "v", "zicbom",
> > + "zicbop", "zicboz", "zicntr", "zicond", "zicsr",
> > + "zifencei", "zihintpause", "zihpm", "zfh", "zba",
> > + "zbb", "zbc", "zbs", "zkt", "zvfh", "zvkt",
> > + "sscofpmf", "sstc", "svinval", "svnapot", "svpbmt";
> > + riscv,cbom-block-size = <64>;
> > + riscv,cbop-block-size = <64>;
> > + riscv,cboz-block-size = <64>;
> > + mmu-type = "riscv,sv39";
> > +
> > + cpu7_intc: interrupt-controller {
> > + compatible = "riscv,cpu-intc";
> > + interrupt-controller;
> > + #interrupt-cells = <1>;
> > + };
> > + };
> > +
> > + };
> > +
> > + soc {
> > + compatible = "simple-bus";
> > + interrupt-parent = <&plic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + dma-noncoherent;
> > + ranges;
> > +
> > + uart0: serial at d4017000 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
>
> no, this is not a correct hw modeling. The doc on spacemit says
> all the uart support 64 bytes FIFO, declaring xscale only makes
> use of 32 bytes FIFO.
yes, I also noticed it's 64 bytes FIFO
>
> IIRC, 8250_pxa is a xscale uart with 64 bytes FIFO, so this should be
> "mrvl,pxa-uart" or "mrvl,mmp-uart"
for mrvl,pxa-uart, I think you imply to use drivers/tty/serial/8250/8250_pxa.c,
which turn out doesn't work on k1 SoC, for the record, we need to adjust
drivers/tty/serial/8250/Kconfig to enable the driver for ARCH_SPACEMIT,
and change uart compatible to "spacemit,k1-uart", "mrvl,pxa-uart"
for mrvl,mmp-uart, I see two choices, one using 8250_pxa.c which has same result
as mrvl,pxa-uart, another choice would using the driver of 8250_of.c
and it work as same as "intel,xscale-uart", I don't see any difference..
P.S: there is possibly a side problem that "mrvl,mmp-uart" from 8250_of.c doesn't
really compatile with "mrvl,mmp-uart" from 8250_pxa.c, but I think it's another story
>
> > + reg = <0x0 0xd4017000 0x0 0x100>;
> > + interrupts = <42>;
> > + clock-frequency = <14857000>;
>
> once clk is ready, you will remove this property and add clk phandles,
yes, this is exactly the plan
> so why not bring clk, pinctrl, reset before hand?
>
No, we want to have an initial minimal working environment with initramfs + console,
and start from there to work with clk, pinctrl, reset, it will help us to debug and
work in parallel
Note, I have no objection, if maintainer consider to merge this patch series on condition that
clk, pinctrl, reset are also ready..
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial at d4017100 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
> > + reg = <0x0 0xd4017100 0x0 0x100>;
> > + interrupts = <44>;
> > + clock-frequency = <14857000>;
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart3: serial at d4017200 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
> > + reg = <0x0 0xd4017200 0x0 0x100>;
> > + interrupts = <45>;
> > + clock-frequency = <14857000>;
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart4: serial at d4017300 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
> > + reg = <0x0 0xd4017300 0x0 0x100>;
> > + interrupts = <46>;
> > + clock-frequency = <14857000>;
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart5: serial at d4017400 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
> > + reg = <0x0 0xd4017400 0x0 0x100>;
> > + interrupts = <47>;
> > + clock-frequency = <14857000>;
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart6: serial at d4017500 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
> > + reg = <0x0 0xd4017500 0x0 0x100>;
> > + interrupts = <48>;
> > + clock-frequency = <14857000>;
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart7: serial at d4017600 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
> > + reg = <0x0 0xd4017600 0x0 0x100>;
> > + interrupts = <49>;
> > + clock-frequency = <14857000>;
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart8: serial at d4017700 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
> > + reg = <0x0 0xd4017700 0x0 0x100>;
> > + interrupts = <50>;
> > + clock-frequency = <14857000>;
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + uart9: serial at d4017800 {
> > + compatible = "spacemit,k1-uart", "intel,xscale-uart";
> > + reg = <0x0 0xd4017800 0x0 0x100>;
> > + interrupts = <51>;
> > + clock-frequency = <14857000>;
> > + reg-shift = <2>;
> > + reg-io-width = <4>;
> > + status = "disabled";
> > + };
> > +
> > + plic: interrupt-controller at e0000000 {
> > + compatible = "spacemit,k1-plic", "sifive,plic-1.0.0";
> > + reg = <0x0 0xe0000000 0x0 0x4000000>;
> > + interrupts-extended = <&cpu0_intc 11>, <&cpu0_intc 9>,
> > + <&cpu1_intc 11>, <&cpu1_intc 9>,
> > + <&cpu2_intc 11>, <&cpu2_intc 9>,
> > + <&cpu3_intc 11>, <&cpu3_intc 9>,
> > + <&cpu4_intc 11>, <&cpu4_intc 9>,
> > + <&cpu5_intc 11>, <&cpu5_intc 9>,
> > + <&cpu6_intc 11>, <&cpu6_intc 9>,
> > + <&cpu7_intc 11>, <&cpu7_intc 9>;
> > + interrupt-controller;
> > + #address-cells = <0>;
> > + #interrupt-cells = <1>;
> > + riscv,ndev = <159>;
> > + };
> > +
> > + clint: timer at e4000000 {
> > + compatible = "spacemit,k1-clint", "sifive,clint0";
> > + reg = <0x0 0xe4000000 0x0 0x10000>;
> > + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>,
> > + <&cpu1_intc 3>, <&cpu1_intc 7>,
> > + <&cpu2_intc 3>, <&cpu2_intc 7>,
> > + <&cpu3_intc 3>, <&cpu3_intc 7>,
> > + <&cpu4_intc 3>, <&cpu4_intc 7>,
> > + <&cpu5_intc 3>, <&cpu5_intc 7>,
> > + <&cpu6_intc 3>, <&cpu6_intc 7>,
> > + <&cpu7_intc 3>, <&cpu7_intc 7>;
> > + };
> > + };
> > +};
> >
> > --
> > 2.45.2
> >
> >
> > _______________________________________________
> > linux-riscv mailing list
> > linux-riscv at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-riscv
--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55
More information about the linux-riscv
mailing list