[PATCH v2 1/8] dt-bindings: pinctrl: Add thead,th1520-pinctrl bindings

[Emil Renner Berthing]

Emil Renner Berthing wrote:
> Rob Herring wrote:
> > On Wed, Jan 03, 2024 at 02:28:38PM +0100, Emil Renner Berthing wrote:
> > > Add bindings for the pin controllers on the T-Head TH1520 RISC-V SoC.
> > >
> > > Signed-off-by: Emil Renner Berthing <emil.renner.berthing at canonical.com>
> > > ---
> > >  .../pinctrl/thead,th1520-pinctrl.yaml         | 372 ++++++++++++++++++
> > >  1 file changed, 372 insertions(+)
> > >  create mode 100644 Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml
> > > new file mode 100644
> > > index 000000000000..d3ad7a7cfdd1
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/pinctrl/thead,th1520-pinctrl.yaml
> > > @@ -0,0 +1,372 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/pinctrl/thead,th1520-pinctrl.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: T-Head TH1520 SoC pin controller
> > > +
> > > +maintainers:
> > > +  - Emil Renner Berthing <emil.renner.berthing at canonical.com>
> > > +
> > > +description: |
> > > +  Pinmux and pinconf controller in the T-Head TH1520 RISC-V SoC.
> > > +
> > > +  The TH1520 has 3 groups of pads each controlled from different memory ranges.
> > > +  Confusingly the memory ranges are named
> > > +    PADCTRL_AOSYS  -> PAD Group 1
> > > +    PADCTRL1_APSYS -> PAD Group 2
> > > +    PADCTRL0_APSYS -> PAD Group 3
> > > +
> > > +  Each pad can be muxed individually to up to 6 different functions. For most
> > > +  pads only a few of those 6 configurations are valid though, and a few pads in
> > > +  group 1 does not support muxing at all.
> > > +
> > > +  Pinconf is fairly regular except for a few pads in group 1 that either can't
> > > +  be configured or has some special functions. The rest have configurable drive
> > > +  strength, input enable, schmitt trigger, slew rate, pull-up and pull-down in
> > > +  addition to a special strong pull up.
> > > +
> > > +  Certain pads in group 1 can be muxed to AUDIO_PA0 - AUDIO_PA30 functions and
> > > +  are then meant to be used by the audio co-processor. Each such pad can then
> > > +  be further muxed to either audio GPIO or one of 4 functions such as UART, I2C
> > > +  and I2S. If the audio pad is muxed to one of the 4 functions then pinconf is
> > > +  also configured in different registers. All of this is done from a different
> > > +  AUDIO_IOCTRL memory range and is left to the audio co-processor for now.
> >
> > It is still not clear to me if each instance is a different programming
> > model or the same with just different connections. The latter should
> > be the same compatible string. That needs to be answered in *this*
> > patch, not a reply.
>
> Hi Rob,
>
> Sorry for the late response. I honestly don't know exactly what you mean by
> differenty programming models and what the difference is, so I'll need a bit of
> help with what you want me to write here.
>
> Any driver for the TH1520 SoC (not just Linux) would need some way to discern
> between the 3 pin controllers so they know how many pins to control and what
> pinmux settings are valid. Basically they'd need the data in the three
> th1520_group{1,2,3}_pins arrays in the driver and a way to know which of them
> to use.
>
> https://lore.kernel.org/linux-riscv/20240103132852.298964-3-emil.renner.berthing@canonical.com/
>
> Another solution would be to just have one compatible value, and then let the
> driver figure out which of the 3 pin controllers it's probing from the base
> physical memory address. That would work fine.
>
> A third solution would be to encode the data in those three arrays into the
> device tree, but I thought we didn't want to encode register information in
> device trees.

Hi Rob,

Any chance you could give me some advice on this, or should I just send it
again as is?

Other patchsets depend on this. Eg.:
https://lore.kernel.org/all/20240618-i2c-th1520-v3-0-3042590a16b1@bootlin.com/

/Emil