[PATCH 07/12] riscv: dts: allwinner: Add Allwinner D1 Nezha devicetree

Samuel Holland samuel at sholland.org
Sun Aug 14 22:08:10 PDT 2022 

"D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
plus low-speed I/O from the SoC and a GPIO expander chip.

Most other D1 boards copied the Nezha's power tree, with the 1.8V rail
powered by the SoCs internal LDOA, analog domains powered by ALDO, and
the rest of the board powered by always-on fixed regulators. Some (but
not all) boards also copied the PWM CPU regulator. To avoid duplication,
factor out the out the regulator references that are common across all
known boards.

Signed-off-by: Samuel Holland <samuel at sholland.org>
---

 arch/riscv/boot/dts/allwinner/Makefile        |   1 +
 .../sun20i-d1-common-regulators.dtsi          |  51 ++++++
 .../boot/dts/allwinner/sun20i-d1-nezha.dts    | 171 ++++++++++++++++++
 3 files changed, 223 insertions(+)
 create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-common-regulators.dtsi
 create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts

diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
index f66554cd5c45..b0a15e8c8d82 100644
--- a/arch/riscv/boot/dts/allwinner/Makefile
+++ b/arch/riscv/boot/dts/allwinner/Makefile
@@ -1 +1,2 @@
 # SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-common-regulators.dtsi b/arch/riscv/boot/dts/allwinner/sun20i-d1-common-regulators.dtsi
new file mode 100644
index 000000000000..143a3e710c3c
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-common-regulators.dtsi
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel at sholland.org>
+
+/ {
+	reg_vcc: vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vcc_3v3: vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc>;
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_aldo>;
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc_3v3>;
+	vcc-pc-supply = <&reg_vcc_3v3>;
+	vcc-pd-supply = <&reg_vcc_3v3>;
+	vcc-pe-supply = <&reg_vcc_3v3>;
+	vcc-pf-supply = <&reg_vcc_3v3>;
+	vcc-pg-supply = <&reg_vcc_3v3>;
+};
+
+&reg_aldo {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	vdd33-supply = <&reg_vcc_3v3>;
+};
+
+&reg_hpldo {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	hpldoin-supply = <&reg_vcc_3v3>;
+};
+
+&reg_ldoa {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	ldo-in-supply = <&reg_vcc_3v3>;
+};
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
new file mode 100644
index 000000000000..df865ee15fcf
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel at sholland.org>
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-d1-common-regulators.dtsi"
+
+/ {
+	model = "Allwinner D1 Nezha";
+	compatible = "allwinner,d1-nezha", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &emac;
+		ethernet1 = &xr829;
+		mmc0 = &mmc0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_usbvbus: usbvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbvbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
+		enable-active-high;
+		vin-supply = <&reg_vcc>;
+	};
+
+	/*
+	 * This regulator is PWM-controlled, but the PWM controller is not
+	 * yet supported, so fix the regulator to its default voltage.
+	 */
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-0 = <&rgmii_pe_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_vcc_3v3>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pb0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pcf8574a: gpio at 38 {
+		compatible = "nxp,pcf8574a";
+		reg = <0x38>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 2 IRQ_TYPE_LEVEL_LOW>; /* PB2 */
+		interrupt-controller;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+};
+
+&lradc {
+	status = "okay";
+
+	button-160 {
+		label = "OK";
+		linux,code = <KEY_OK>;
+		channel = <0>;
+		voltage = <160000>;
+	};
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy at 1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	xr829: wifi at 1 {
+		reg = <1>;
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* XR829 bluetooth is connected here */
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */
+	usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+	usb0_vbus-supply = <&reg_usbvbus>;
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
-- 
2.35.1

More information about the linux-riscv mailing list