[PATCH v3 1/2] dt-bindings: phy: qcom: Add CSI2 C-PHY/DPHY schema

[Bryan O'Donoghue]

On 03/03/2026 23:50, Vijay Kumar Tumati wrote:
> Sure, I was just giving an example. I haven't looked a lot into the 
> IPCAT / clock corners of this target particularly. Someone needs to 
> check the clock plan, 

I mean, feel free.

understand which PHYs require which power domains
> and add that in the following OPP table and as for scaling you can use 
> the same RPMH levels for all those power domains. Btw, if you had 
> defined the below OPP table for TOP GDSC, I think that is wrong. It only 
> has two perf states (on and off) and doesn't need OPP scaling. If you 
> look at the Iris driver, they link only the mxc and mmcx power domains 
> to the OPP table using 'PD_FLAG_REQUIRED_OPP, not the GDSCs.
>>
>> +    csiphy_opp_table: opp-table-csiphy {
>> +        compatible = "operating-points-v2";
>> +
>> +        opp-300000000 {
>> +            opp-hz = /bits/ 64 <300000000>;
>> +            required-opps = <&rpmhpd_opp_low_svs_d1>;
>> +        };
>> +
>> +        opp-400000000 {
>> +            opp-hz = /bits/ 64 <400000000>;
>> +            required-opps = <&rpmhpd_opp_low_svs>;
>> +        };
>> +
>> +        opp-480000000 {
>> +            opp-hz = /bits/ 64 <480000000>;
>> +            required-opps = <&rpmhpd_opp_low_svs>;
>> +        };
>> +    };
>>
>> ---
>> bod 

Yes, we should scale the MX*, that's incorrect.

csiphy_mxc_opp_table: opp-table-csiphy-mxc {
     compatible = "operating-points-v2";

     opp-300000000 {
         opp-hz = /bits/ 64 <300000000>;
         required-opps = <&rpmhpd_opp_low_svs_d1>,
                         <&rpmhpd_opp_low_svs_d1>;
     };

     opp-400000000 {
         opp-hz = /bits/ 64 <400000000>;
         required-opps = <&rpmhpd_opp_low_svs>,
                         <&rpmhpd_opp_low_svs>;
     };

     opp-480000000 {
         opp-hz = /bits/ 64 <480000000>;
         required-opps = <&rpmhpd_opp_low_svs>,
                         <&rpmhpd_opp_low_svs>;
     };
};

csiphy_mxa_opp_table: opp-table-csiphy-mxa {
     compatible = "operating-points-v2";

     opp-300000000 {
         opp-hz = /bits/ 64 <300000000>;
         required-opps = <&rpmhpd_opp_low_svs_d1>,
                         <&rpmhpd_opp_low_svs_d1>;
     };

     opp-400000000 {
         opp-hz = /bits/ 64 <400000000>;
         required-opps = <&rpmhpd_opp_low_svs>,
                         <&rpmhpd_opp_low_svs>;
     };

     opp-480000000 {
         opp-hz = /bits/ 64 <480000000>;
         required-opps = <&rpmhpd_opp_low_svs>,
                         <&rpmhpd_opp_low_svs>;
     };
};

csiphy0: phy at ace4000 {
     power-domains = <&rpmhpd RPMHPD_MXC>,
                     <&rpmhpd RPMHPD_MMCX>;
     operating-points-v2 = <&csiphy_mxc_opp_table>;
     ...
};

csiphy4: phy at acec000 {
     power-domains = <&rpmhpd RPMHPD_MXA>,
                     <&rpmhpd RPMHPD_MMCX>;
     operating-points-v2 = <&csiphy_mxa_opp_table>;
     ...
};

---
bod