[PATCH v3 2/2] arm64: dts: qcom: Add PCIe3 and PCIe5 regulators for HAMAO-IOT-EVK board

[Bjorn Andersson]

On Wed, Nov 12, 2025 at 05:03:16PM +0800, Ziyue Zhang wrote:
> HAMAO IoT EVK uses PCIe5 to connect an SDX65 module for WWAN functionality
> and PCIe3 to connect a SATA controller. These interfaces require multiple
> voltage rails: PCIe5 needs 3.3V supplied by vreg_wwan, while PCIe3 requires
> 12V, 3.3V, and 3.3V AUX rails, controlled via PMIC GPIOs.
> 

I love it! Thank you for the clear description.

Regards,
Bjorn

> Add the required fixed regulators with related pin configuration, and
> connect them to the PCIe3 and PCIe5 ports to ensure proper power for the
> SDX65 module and SATA controller.
> 
> Signed-off-by: Ziyue Zhang <ziyue.zhang at oss.qualcomm.com>
> Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru at oss.qualcomm.com>
> ---
>  arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 83 ++++++++++++++++++++++
>  1 file changed, 83 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> index 36dd6599402b..ac17f7cb8b3d 100644
> --- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> @@ -199,6 +199,48 @@ vreg_nvme: regulator-nvme {
>  		regulator-boot-on;
>  	};
>  
> +	vreg_pcie_12v: regulator-pcie-12v {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_PCIE_12V";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +
> +		gpio = <&pm8550ve_8_gpios 8 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&pcie_x8_12v>;
> +		pinctrl-names = "default";
> +	};
> +
> +	vreg_pcie_3v3: regulator-pcie-3v3 {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_PCIE_3P3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&pmc8380_3_gpios 6 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&pm_sde7_main_3p3_en>;
> +		pinctrl-names = "default";
> +	};
> +
> +	vreg_pcie_3v3_aux: regulator-pcie-3v3-aux {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VREG_PCIE_3P3_AUX";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpio = <&pmc8380_3_gpios 8 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&pm_sde7_aux_3p3_en>;
> +		pinctrl-names = "default";
> +	};
> +
>  	/* Left unused as the retimer is not used on this board. */
>  	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
>  		compatible = "regulator-fixed";
> @@ -844,6 +886,16 @@ &mdss_dp3_phy {
>  	status = "okay";
>  };
>  
> +&pcie3_port {
> +	vpcie12v-supply = <&vreg_pcie_12v>;
> +	vpcie3v3-supply = <&vreg_pcie_3v3>;
> +	vpcie3v3aux-supply = <&vreg_pcie_3v3_aux>;
> +};
> +
> +&pcie5 {
> +	vddpe-3v3-supply = <&vreg_wwan>;
> +};
> +
>  &pcie6a {
>  	vddpe-3v3-supply = <&vreg_nvme>;
>  };
> @@ -868,6 +920,17 @@ usb0_3p3_reg_en: usb0-3p3-reg-en-state {
>  	};
>  };
>  
> +&pm8550ve_8_gpios {
> +	pcie_x8_12v: pcie-12v-default-state {
> +		pins = "gpio8";
> +		function = "normal";
> +		output-enable;
> +		output-high;
> +		bias-pull-down;
> +		power-source = <0>;
> +	};
> +};
> +
>  &pm8550ve_9_gpios {
>  	usb0_1p8_reg_en: usb0-1p8-reg-en-state {
>  		pins = "gpio8";
> @@ -879,6 +942,26 @@ usb0_1p8_reg_en: usb0-1p8-reg-en-state {
>  	};
>  };
>  
> +&pmc8380_3_gpios {
> +	pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state {
> +		pins = "gpio8";
> +		function = "normal";
> +		output-enable;
> +		output-high;
> +		bias-pull-down;
> +		power-source = <0>;
> +	};
> +
> +	pm_sde7_main_3p3_en: pcie-main-3p3-default-state {
> +		pins = "gpio6";
> +		function = "normal";
> +		output-enable;
> +		output-high;
> +		bias-pull-down;
> +		power-source = <0>;
> +	};
> +};
> +
>  &pmc8380_5_gpios {
>  	usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
>  		pins = "gpio8";
> -- 
> 2.34.1
>