[PATCH v3 2/2] arm64: dts: qcom: Add PCIe3 and PCIe5 regulators for HAMAO-IOT-EVK board

[Ziyue Zhang]

HAMAO IoT EVK uses PCIe5 to connect an SDX65 module for WWAN functionality
and PCIe3 to connect a SATA controller. These interfaces require multiple
voltage rails: PCIe5 needs 3.3V supplied by vreg_wwan, while PCIe3 requires
12V, 3.3V, and 3.3V AUX rails, controlled via PMIC GPIOs.

Add the required fixed regulators with related pin configuration, and
connect them to the PCIe3 and PCIe5 ports to ensure proper power for the
SDX65 module and SATA controller.

Signed-off-by: Ziyue Zhang <ziyue.zhang at oss.qualcomm.com>
Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru at oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 83 ++++++++++++++++++++++
 1 file changed, 83 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
index 36dd6599402b..ac17f7cb8b3d 100644
--- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
@@ -199,6 +199,48 @@ vreg_nvme: regulator-nvme {
 		regulator-boot-on;
 	};
 
+	vreg_pcie_12v: regulator-pcie-12v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+
+		gpio = <&pm8550ve_8_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pcie_x8_12v>;
+		pinctrl-names = "default";
+	};
+
+	vreg_pcie_3v3: regulator-pcie-3v3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8380_3_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pm_sde7_main_3p3_en>;
+		pinctrl-names = "default";
+	};
+
+	vreg_pcie_3v3_aux: regulator-pcie-3v3-aux {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_PCIE_3P3_AUX";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8380_3_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&pm_sde7_aux_3p3_en>;
+		pinctrl-names = "default";
+	};
+
 	/* Left unused as the retimer is not used on this board. */
 	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
 		compatible = "regulator-fixed";
@@ -844,6 +886,16 @@ &mdss_dp3_phy {
 	status = "okay";
 };
 
+&pcie3_port {
+	vpcie12v-supply = <&vreg_pcie_12v>;
+	vpcie3v3-supply = <&vreg_pcie_3v3>;
+	vpcie3v3aux-supply = <&vreg_pcie_3v3_aux>;
+};
+
+&pcie5 {
+	vddpe-3v3-supply = <&vreg_wwan>;
+};
+
 &pcie6a {
 	vddpe-3v3-supply = <&vreg_nvme>;
 };
@@ -868,6 +920,17 @@ usb0_3p3_reg_en: usb0-3p3-reg-en-state {
 	};
 };
 
+&pm8550ve_8_gpios {
+	pcie_x8_12v: pcie-12v-default-state {
+		pins = "gpio8";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+};
+
 &pm8550ve_9_gpios {
 	usb0_1p8_reg_en: usb0-1p8-reg-en-state {
 		pins = "gpio8";
@@ -879,6 +942,26 @@ usb0_1p8_reg_en: usb0-1p8-reg-en-state {
 	};
 };
 
+&pmc8380_3_gpios {
+	pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state {
+		pins = "gpio8";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+
+	pm_sde7_main_3p3_en: pcie-main-3p3-default-state {
+		pins = "gpio6";
+		function = "normal";
+		output-enable;
+		output-high;
+		bias-pull-down;
+		power-source = <0>;
+	};
+};
+
 &pmc8380_5_gpios {
 	usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
 		pins = "gpio8";
-- 
2.34.1