[PATCH v2 1/3] dt-bindings: ata: eswin: Document for EIC7700 SoC ahci

[luyulin at eswincomputing.com]

> On Thu, Aug 28, 2025 at 06:22:40PM +0800, luyulin at eswincomputing.com wrote:
> > 
> > Do you mean that ports-implemented should be removed from the dts,
> > and the corresponding register should be configured by the firmware
> > (which is U-Boot on the HiFive Premier P550 board)? Is this understanding correct?
> > If so, when the driver is removed, a reset will be triggered,
> > causing the configuration of this register to be lost,
> > which will result in an error when insmod the driver again.
> 
> My 50 cents,
> 
> if the ports implemented register gets reset from the reset_control_reset()
> in ahci_platform_assert_rsts(), then it seems like having ports-implemented
> in device tree is acceptable.
> 

In our design, the ports implemented register gets reset from the ahci_platform_assert_rsts().

> There are a bunch of device trees that have this already:
> arch/arm/boot/dts/qcom/qcom-apq8064.dtsi:                       ports-implemented = <0x1>;
> arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi:                  ports-implemented = <0x1>;
> arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi:  ports-implemented = <0x1>;
> arch/arm/boot/dts/samsung/exynos5250.dtsi:                      ports-implemented = <0x1>;
> arch/arm/boot/dts/socionext/uniphier-pro4.dtsi:                 ports-implemented = <1>;
> arch/arm/boot/dts/socionext/uniphier-pro4.dtsi:                 ports-implemented = <1>;
> arch/arm/boot/dts/socionext/uniphier-pxs2.dtsi:                 ports-implemented = <1>;
> arch/arm/boot/dts/st/stih407-family.dtsi:                       ports-implemented = <0x1>;
> arch/arm/boot/dts/st/stih407-family.dtsi:                       ports-implemented = <0x1>;
> arch/arm/boot/dts/ti/omap/dra7-l4.dtsi:                         ports-implemented = <0x1>;
> arch/arm/boot/dts/ti/omap/omap5-l4.dtsi:                                ports-implemented = <0x1>;
> arch/arm64/boot/dts/mediatek/mt7622.dtsi:               ports-implemented = <0x1>;
> arch/arm64/boot/dts/rockchip/rk3568.dtsi:               ports-implemented = <0x1>;
> arch/arm64/boot/dts/rockchip/rk356x-base.dtsi:          ports-implemented = <0x1>;
> arch/arm64/boot/dts/rockchip/rk356x-base.dtsi:          ports-implemented = <0x1>;
> arch/arm64/boot/dts/rockchip/rk3576.dtsi:                       ports-implemented = <0x1>;
> arch/arm64/boot/dts/rockchip/rk3576.dtsi:                       ports-implemented = <0x1>;
> arch/arm64/boot/dts/rockchip/rk3588-base.dtsi:          ports-implemented = <0x1>;
> arch/arm64/boot/dts/rockchip/rk3588-base.dtsi:          ports-implemented = <0x1>;
> arch/arm64/boot/dts/rockchip/rk3588-extra.dtsi:         ports-implemented = <0x1>;
> arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi:                       ports-implemented = <1>;
> arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi:                       ports-implemented = <1>;
> 
> 
> Sure, if the ports implemented register was sticky (kept its value after a
> reset), then I think Rob's suggestion would make sense.
> 
> 

Thank you very much for the clarification.

> 
> Kind regards,
> Niklas

Best regards,
Yulin