[PATCH v2 5/5] arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100
Qiang Yu
quic_qianyu at quicinc.com
Thu Sep 19 07:05:38 PDT 2024
On 9/13/2024 9:57 PM, Manivannan Sadhasivam wrote:
> On Fri, Sep 13, 2024 at 01:37:24AM -0700, Qiang Yu wrote:
>> Describe PCIe3 controller and PHY. Also add required system resources like
>> regulators, clocks, interrupts and registers configuration for PCIe3.
>>
>> Signed-off-by: Qiang Yu <quic_qianyu at quicinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/x1e80100.dtsi | 202 ++++++++++++++++++++++++-
>> 1 file changed, 201 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
>> index a36076e3c56b..a7703e4974a6 100644
>> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
>> @@ -744,7 +744,7 @@ gcc: clock-controller at 100000 {
>>
>> clocks = <&bi_tcxo_div2>,
>> <&sleep_clk>,
>> - <0>,
>> + <&pcie3_phy>,
>> <&pcie4_phy>,
>> <&pcie5_phy>,
>> <&pcie6a_phy>,
>> @@ -2907,6 +2907,206 @@ mmss_noc: interconnect at 1780000 {
>> #interconnect-cells = <2>;
>> };
>>
>> + pcie3: pci at 1bd0000 {
> pcie@
>
>> + device_type = "pci";
>> + compatible = "qcom,pcie-x1e80100";
>> + reg = <0 0x01bd0000 0 0x3000>,
>> + <0 0x78000000 0 0xf1d>,
> 0x0 here and below.
>
>> + <0 0x78000f40 0 0xa8>,
>> + <0 0x78001000 0 0x1000>,
>> + <0 0x78100000 0 0x100000>,
>> + <0 0x01bd3000 0 0x1000>;
>> + reg-names = "parf",
>> + "dbi",
>> + "elbi",
>> + "atu",
>> + "config",
>> + "mhi";
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + ranges = <0x01000000 0x0 0x00000000 0x0 0x78200000 0x0 0x100000>,
>> + <0x02000000 0x0 0x78300000 0x0 0x78300000 0x0 0x3d00000>,
>> + <0x03000000 0x7 0x40000000 0x7 0x40000000 0x0 0x40000000>;
>> + bus-range = <0x00 0xff>;
>> +
>> + dma-coherent;
>> +
>> + linux,pci-domain = <3>;
>> + num-lanes = <8>;
>> +
>> + interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "msi0",
>> + "msi1",
>> + "msi2",
>> + "msi3",
>> + "msi4",
>> + "msi5",
>> + "msi6",
>> + "msi7";
> Can you add 'global' interrupt as well? While doing so, please make sure the
> global_irq related patches are applied and Link up works fine. Those patches are
> already in linux-next.
Sure, let me add global interrupt and have a try. Will also update patch
according to your other comments.
Thanks,
Qiang
>
>> +
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0x7>;
>> + interrupt-map = <0 0 0 1 &intc 0 0 0 220 IRQ_TYPE_LEVEL_HIGH>,
> Use GIC_SPI for the parent interrupt specifier.
>
> - Mani
>
>> + <0 0 0 2 &intc 0 0 0 221 IRQ_TYPE_LEVEL_HIGH>,
>> + <0 0 0 3 &intc 0 0 0 237 IRQ_TYPE_LEVEL_HIGH>,
>> + <0 0 0 4 &intc 0 0 0 238 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + clocks = <&gcc GCC_PCIE_3_AUX_CLK>,
>> + <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
>> + <&gcc GCC_PCIE_3_MSTR_AXI_CLK>,
>> + <&gcc GCC_PCIE_3_SLV_AXI_CLK>,
>> + <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>,
>> + <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>,
>> + <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>;
>> + clock-names = "aux",
>> + "cfg",
>> + "bus_master",
>> + "bus_slave",
>> + "slave_q2a",
>> + "noc_aggr",
>> + "cnoc_sf_axi";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>;
>> + assigned-clock-rates = <19200000>;
>> +
>> + interconnects = <&pcie_south_anoc MASTER_PCIE_3 QCOM_ICC_TAG_ALWAYS
>> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
>> + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
>> + &cnoc_main SLAVE_PCIE_3 QCOM_ICC_TAG_ALWAYS>;
>> + interconnect-names = "pcie-mem",
>> + "cpu-pcie";
>> +
>> + resets = <&gcc GCC_PCIE_3_BCR>,
>> + <&gcc GCC_PCIE_3_LINK_DOWN_BCR>;
>> + reset-names = "pci",
>> + "link_down";
>> +
>> + power-domains = <&gcc GCC_PCIE_3_GDSC>;
>> +
>> + phys = <&pcie3_phy>;
>> + phy-names = "pciephy";
>> +
>> + operating-points-v2 = <&pcie3_opp_table>;
>> +
>> + status = "disabled";
>> +
>> + pcie3_opp_table: opp-table {
>> + compatible = "operating-points-v2";
>> +
>> + /* GEN 1 x1 */
>> + opp-2500000 {
>> + opp-hz = /bits/ 64 <2500000>;
>> + required-opps = <&rpmhpd_opp_low_svs>;
>> + opp-peak-kBps = <250000 1>;
>> + };
>> +
>> + /* GEN 1 x2 and GEN 2 x1 */
>> + opp-5000000 {
>> + opp-hz = /bits/ 64 <5000000>;
>> + required-opps = <&rpmhpd_opp_low_svs>;
>> + opp-peak-kBps = <500000 1>;
>> + };
>> +
>> + /* GEN 1 x4 and GEN 2 x2 */
>> + opp-10000000 {
>> + opp-hz = /bits/ 64 <10000000>;
>> + required-opps = <&rpmhpd_opp_low_svs>;
>> + opp-peak-kBps = <1000000 1>;
>> + };
>> +
>> + /* GEN 1 x8 and GEN 2 x4 */
>> + opp-20000000 {
>> + opp-hz = /bits/ 64 <20000000>;
>> + required-opps = <&rpmhpd_opp_low_svs>;
>> + opp-peak-kBps = <2000000 1>;
>> + };
>> +
>> + /* GEN 2 x8 */
>> + opp-40000000 {
>> + opp-hz = /bits/ 64 <40000000>;
>> + required-opps = <&rpmhpd_opp_low_svs>;
>> + opp-peak-kBps = <4000000 1>;
>> + };
>> +
>> + /* GEN 3 x1 */
>> + opp-8000000 {
>> + opp-hz = /bits/ 64 <8000000>;
>> + required-opps = <&rpmhpd_opp_svs>;
>> + opp-peak-kBps = <984500 1>;
>> + };
>> +
>> + /* GEN 3 x2 and GEN 4 x1 */
>> + opp-16000000 {
>> + opp-hz = /bits/ 64 <16000000>;
>> + required-opps = <&rpmhpd_opp_svs>;
>> + opp-peak-kBps = <1969000 1>;
>> + };
>> +
>> + /* GEN 3 x4 and GEN 4 x2 */
>> + opp-32000000 {
>> + opp-hz = /bits/ 64 <32000000>;
>> + required-opps = <&rpmhpd_opp_svs>;
>> + opp-peak-kBps = <3938000 1>;
>> + };
>> +
>> + /* GEN 3 x8 and GEN 4 x4 */
>> + opp-64000000 {
>> + opp-hz = /bits/ 64 <64000000>;
>> + required-opps = <&rpmhpd_opp_svs>;
>> + opp-peak-kBps = <7876000 1>;
>> + };
>> +
>> + /* GEN 4 x8 */
>> + opp-128000000 {
>> + opp-hz = /bits/ 64 <128000000>;
>> + required-opps = <&rpmhpd_opp_svs>;
>> + opp-peak-kBps = <15753000 1>;
>> + };
>> + };
>> + };
>> +
>> + pcie3_phy: phy at 1be0000 {
>> + compatible = "qcom,x1e80100-qmp-gen4x8-pcie-phy";
>> + reg = <0 0x01be0000 0 0x10000>;
>> +
>> + clocks = <&gcc GCC_PCIE_3_PHY_AUX_CLK>,
>> + <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
>> + <&tcsr TCSR_PCIE_8L_CLKREF_EN>,
>> + <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>,
>> + <&gcc GCC_PCIE_3_PIPE_CLK>,
>> + <&gcc GCC_PCIE_3_PIPEDIV2_CLK>;
>> + clock-names = "aux",
>> + "cfg_ahb",
>> + "ref",
>> + "rchng",
>> + "pipe",
>> + "pipediv2";
>> +
>> + resets = <&gcc GCC_PCIE_3_PHY_BCR>,
>> + <&gcc GCC_PCIE_3_NOCSR_COM_PHY_BCR>;
>> + reset-names = "phy",
>> + "phy_nocsr";
>> +
>> + assigned-clocks = <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>;
>> + assigned-clock-rates = <100000000>;
>> +
>> + power-domains = <&gcc GCC_PCIE_3_PHY_GDSC>;
>> +
>> + #clock-cells = <0>;
>> + clock-output-names = "pcie3_pipe_clk";
>> +
>> + #phy-cells = <0>;
>> +
>> + status = "disabled";
>> + };
>> +
>> pcie6a: pci at 1bf8000 {
>> device_type = "pci";
>> compatible = "qcom,pcie-x1e80100";
>> --
>> 2.34.1
>>
More information about the linux-phy
mailing list