[PATCH V8 02/12] phy: freescale: add Samsung HDMI PHY
Adam Ford
aford173 at gmail.com
Mon Feb 5 19:39:04 PST 2024
On Mon, Feb 5, 2024 at 2:17 AM Marco Felsch <m.felsch at pengutronix.de> wrote:
>
> On 24-02-04, Dmitry Baryshkov wrote:
> > On Sat, 3 Feb 2024 at 17:53, Adam Ford <aford173 at gmail.com> wrote:
> > >
> > > From: Lucas Stach <l.stach at pengutronix.de>
> > >
> > > This adds the driver for the Samsung HDMI PHY found on the
> > > i.MX8MP SoC.
> > >
> > > Signed-off-by: Lucas Stach <l.stach at pengutronix.de>
> > > Signed-off-by: Adam Ford <aford173 at gmail.com>
> > > Tested-by: Alexander Stein <alexander.stein at ew.tq-group.com>
> > > ---
> > > V4: Make lookup table hex values lower case.
> > >
> > > V3: Re-order the Makefile to keep it alphabetical
> > > Remove unused defines
> > >
> > > V2: Fixed some whitespace found from checkpatch
> > > Change error handling when enabling apbclk to use dev_err_probe
> > > Rebase on Linux-Next
> > >
> > > I (Adam) tried to help move this along, so I took Lucas' patch and
> > > attempted to apply fixes based on feedback. I don't have
> > > all the history, so apologies for that.
> > > ---
> > > drivers/phy/freescale/Kconfig | 6 +
> > > drivers/phy/freescale/Makefile | 1 +
> > > drivers/phy/freescale/phy-fsl-samsung-hdmi.c | 1075 ++++++++++++++++++
> > > 3 files changed, 1082 insertions(+)
> > > create mode 100644 drivers/phy/freescale/phy-fsl-samsung-hdmi.c
> > >
> > > diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
> > > index 853958fb2c06..5c2b73042dfc 100644
> > > --- a/drivers/phy/freescale/Kconfig
> > > +++ b/drivers/phy/freescale/Kconfig
> > > @@ -35,6 +35,12 @@ config PHY_FSL_IMX8M_PCIE
> > > Enable this to add support for the PCIE PHY as found on
> > > i.MX8M family of SOCs.
> > >
> > > +config PHY_FSL_SAMSUNG_HDMI_PHY
> > > + tristate "Samsung HDMI PHY support"
> > > + depends on OF && HAS_IOMEM
> > > + help
> > > + Enable this to add support for the Samsung HDMI PHY in i.MX8MP.
> > > +
> > > endif
> > >
> > > config PHY_FSL_LYNX_28G
> > > diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
> > > index cedb328bc4d2..79e5f16d3ce8 100644
> > > --- a/drivers/phy/freescale/Makefile
> > > +++ b/drivers/phy/freescale/Makefile
> > > @@ -4,3 +4,4 @@ obj-$(CONFIG_PHY_MIXEL_LVDS_PHY) += phy-fsl-imx8qm-lvds-phy.o
> > > obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
> > > obj-$(CONFIG_PHY_FSL_IMX8M_PCIE) += phy-fsl-imx8m-pcie.o
> > > obj-$(CONFIG_PHY_FSL_LYNX_28G) += phy-fsl-lynx-28g.o
> > > +obj-$(CONFIG_PHY_FSL_SAMSUNG_HDMI_PHY) += phy-fsl-samsung-hdmi.o
> > > diff --git a/drivers/phy/freescale/phy-fsl-samsung-hdmi.c b/drivers/phy/freescale/phy-fsl-samsung-hdmi.c
> > > new file mode 100644
> > > index 000000000000..bf0e2299d00f
> > > --- /dev/null
> > > +++ b/drivers/phy/freescale/phy-fsl-samsung-hdmi.c
> > > @@ -0,0 +1,1075 @@
> > > +// SPDX-License-Identifier: GPL-2.0+
> > > +/*
> > > + * Copyright 2020 NXP
> > > + * Copyright 2022 Pengutronix, Lucas Stach <kernel at pengutronix.de>
> > > + */
> > > +
> > > +#include <linux/clk-provider.h>
> > > +#include <linux/clk.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/io.h>
> > > +#include <linux/iopoll.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of_device.h>
> > > +#include <linux/of.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/pm_runtime.h>
> > > +
> > > +#define PHY_REG_33 0x84
> > > +#define REG33_MODE_SET_DONE BIT(7)
> > > +#define REG33_FIX_DA BIT(1)
> > > +
> > > +#define PHY_REG_34 0x88
> > > +#define REG34_PHY_READY BIT(7)
> > > +#define REG34_PLL_LOCK BIT(6)
> > > +#define REG34_PHY_CLK_READY BIT(5)
> > > +
> > > +
> > > +#define PHY_PLL_REGS_NUM 48
> > > +
> > > +struct phy_config {
> > > + u32 clk_rate;
> > > + u8 regs[PHY_PLL_REGS_NUM];
> > > +};
> > > +
> > > +const struct phy_config phy_pll_cfg[] = {
> > > + { 22250000, {
> > > + 0x00, 0xd1, 0x4b, 0xf1, 0x89, 0x88, 0x80, 0x40,
> > > + 0x4f, 0x30, 0x33, 0x65, 0x00, 0x15, 0x25, 0x80,
> > > + 0x6c, 0xf2, 0x67, 0x00, 0x10, 0x8f, 0x30, 0x32,
> > > + 0x60, 0x8f, 0x00, 0x00, 0x08, 0x00, 0x00, 0x00,
> > > + 0x00, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > > + 0x00, 0xe0, 0x83, 0x0f, 0x3e, 0xf8, 0x00, 0x00,
> > > + },
> > > + }, {
> > > + 23750000, {
> > > + 0x00, 0xd1, 0x50, 0xf1, 0x86, 0x85, 0x80, 0x40,
> > > + 0x4f, 0x30, 0x33, 0x65, 0x00, 0x03, 0x25, 0x80,
> > > + 0x6c, 0xf2, 0x67, 0x00, 0x10, 0x8f, 0x30, 0x32,
> > > + 0x60, 0x8f, 0x00, 0x00, 0x08, 0x00, 0x00, 0x00,
> > > + 0x00, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > > + 0x00, 0xe0, 0x83, 0x0f, 0x3e, 0xf8, 0x00, 0x00,
> > > + },
> >
> > Generally I see that these entries contain a high level of duplication.
> > Could you please extract the common part and a rate-dependent part.
> > Next, it would be best if instead of writing the register values via
> > the rate LUT, the driver could calculate those values.
> > This allows us to support other HDMI modes if the need arises at some point.
>
> Hi Adam,
>
> can you please have a look at: https://lore.kernel.org/all/4830698.GXAFRqVoOG@steina-w/
>
> there we have fixed this already. Not sure which version you picked for
> your work.
It must have been an earlier version. I got the list from Fabio, but
I might have also gotten it mixed up. I'll look at this version and
base my series on it and try to address comments others made. It'll
likely take me a few days to catch up.
thanks for the pointer.
adam
>
> Regards,
> Marco
>
> >
> > > + }, {
> > > + 24000000, {
> > > + 0x00, 0xd1, 0x50, 0xf0, 0x00, 0x00, 0x80, 0x00,
> > > + 0x4f, 0x30, 0x33, 0x65, 0x00, 0x01, 0x25, 0x80,
> > > + 0x6c, 0xf2, 0x67, 0x00, 0x10, 0x8f, 0x30, 0x32,
> > > + 0x60, 0x8f, 0x00, 0x00, 0x08, 0x00, 0x00, 0x00,
> > > + 0x00, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > > + 0x00, 0xe0, 0x83, 0x0f, 0x3e, 0xf8, 0x00, 0x00,
> > > + },
> >
> >
> > --
> > With best wishes
> > Dmitry
> >
> >
More information about the linux-phy
mailing list