[PATCH V2 5/6] arm64: dts: qcom: ipq5018: Add PCIe related nodes
Manivannan Sadhasivam
manivannan.sadhasivam at linaro.org
Fri Aug 30 01:59:01 PDT 2024
On Tue, Aug 27, 2024 at 10:27:56AM +0530, Sricharan R wrote:
> From: Nitheesh Sekar <quic_nsekar at quicinc.com>
>
> Add phy and controller nodes for a 2-lane Gen2 and
> 1-lane Gen2 PCIe buses.
>
> Signed-off-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
> Signed-off-by: Sricharan R <quic_srichara at quicinc.com>
> ---
> [v2] Removed relocatable flags, removed assigned-clock-rates,
> fixed rest of the cosmetic comments.
>
> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 168 +++++++++++++++++++++++++-
> 1 file changed, 166 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> index 7e6e2c121979..dd5d6b7ff094 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> @@ -9,6 +9,7 @@
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
> #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
> +#include <dt-bindings/gpio/gpio.h>
>
> / {
> interrupt-parent = <&intc>;
> @@ -143,7 +144,33 @@ usbphy0: phy at 5b000 {
> resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
>
> #phy-cells = <0>;
> + };
> +
> + pcie_x1phy: phy at 7e000{
> + compatible = "qcom,ipq5018-uniphy-pcie-gen2x1";
> + reg = <0x0007e000 0x800>;
> + #phy-cells = <0>;
> + #clock-cells = <0>;
> + clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
> + clock-names = "pipe";
> + assigned-clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> + status = "disabled";
> + };
>
> + pcie_x2phy: phy at 86000{
> + compatible = "qcom,ipq5018-uniphy-pcie-gen2x2";
> + reg = <0x00086000 0x1000>;
> + #phy-cells = <0>;
> + #clock-cells = <0>;
> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> + clock-names = "pipe";
> + assigned-clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
> + reset-names = "phy", "common";
> status = "disabled";
> };
>
> @@ -170,8 +197,8 @@ gcc: clock-controller at 1800000 {
> reg = <0x01800000 0x80000>;
> clocks = <&xo_board_clk>,
> <&sleep_clk>,
> - <0>,
> - <0>,
> + <&pcie_x2phy>,
> + <&pcie_x1phy>,
> <0>,
> <0>,
> <0>,
> @@ -387,6 +414,143 @@ frame at b128000 {
> status = "disabled";
> };
> };
> +
> + pcie0: pci at 80000000 {
pcie@
> + compatible = "qcom,pcie-ipq5018";
> + reg = <0x80000000 0xf1d>,
> + <0x80000f20 0xa8>,
> + <0x80001000 0x1000>,
> + <0x00078000 0x3000>,
> + <0x80100000 0x1000>;
Are you sure that the config space is only 4K?
> + reg-names = "dbi", "elbi", "atu", "parf", "config";
> + device_type = "pci";
> + linux,pci-domain = <0>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <1>;
> + max-link-speed = <2>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + phys = <&pcie_x1phy>;
> + phy-names ="pciephy";
> +
> + ranges = <0x01000000 0 0x80200000 0x80200000 0 0x00100000
Please check the value of this field in other SoCs.
> + 0x02000000 0 0x80300000 0x80300000 0 0x10000000>;
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 0 142 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 0 143 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 0 144 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 0 145 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "global_irq";
I'm pretty sure that this SoC has SPI based MSI interrupts. So they should be
described even though ITS is supported.
> +
> + clocks = <&gcc GCC_SYS_NOC_PCIE1_AXI_CLK>,
> + <&gcc GCC_PCIE1_AXI_M_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_CLK>,
> + <&gcc GCC_PCIE1_AHB_CLK>,
> + <&gcc GCC_PCIE1_AUX_CLK>,
> + <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>;
> +
> + clock-names = "iface",
> + "axi_m",
> + "axi_s",
> + "ahb",
> + "aux",
> + "axi_bridge";
> +
> + resets = <&gcc GCC_PCIE1_PIPE_ARES>,
> + <&gcc GCC_PCIE1_SLEEP_ARES>,
> + <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_MASTER_ARES>,
> + <&gcc GCC_PCIE1_AXI_SLAVE_ARES>,
> + <&gcc GCC_PCIE1_AHB_ARES>,
> + <&gcc GCC_PCIE1_AXI_MASTER_STICKY_ARES>,
> + <&gcc GCC_PCIE1_AXI_SLAVE_STICKY_ARES>;
> +
> + reset-names = "pipe",
> + "sleep",
> + "sticky",
> + "axi_m",
> + "axi_s",
> + "ahb",
> + "axi_m_sticky",
> + "axi_s_sticky";
> +
> + msi-map = <0x0 &v2m0 0x0 0xff8>;
> + status = "disabled";
Please add the rootport node also as like other SoCs.
Above comments applies to below PCIe node.
- Mani
> + };
> +
> + pcie1: pci at a0000000 {
> + compatible = "qcom,pcie-ipq5018";
> + reg = <0xa0000000 0xf1d>,
> + <0xa0000f20 0xa8>,
> + <0xa0001000 0x1000>,
> + <0x00080000 0x3000>,
> + <0xa0100000 0x1000>;
> + reg-names = "dbi", "elbi", "atu", "parf", "config";
> + device_type = "pci";
> + linux,pci-domain = <1>;
> + bus-range = <0x00 0xff>;
> + num-lanes = <2>;
> + max-link-speed = <2>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + phys = <&pcie_x2phy>;
> + phy-names ="pciephy";
> +
> + ranges = <0x01000000 0 0xa0200000 0xa0200000 0 0x00100000
> + 0x02000000 0 0xa0300000 0xa0300000 0 0x10000000>;
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc 0 0 75 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc 0 0 78 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc 0 0 79 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc 0 0 83 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "global_irq";
> +
> + clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
> + <&gcc GCC_PCIE0_AXI_M_CLK>,
> + <&gcc GCC_PCIE0_AXI_S_CLK>,
> + <&gcc GCC_PCIE0_AHB_CLK>,
> + <&gcc GCC_PCIE0_AUX_CLK>,
> + <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>;
> +
> + clock-names = "iface",
> + "axi_m",
> + "axi_s",
> + "ahb",
> + "aux",
> + "axi_bridge";
> +
> + resets = <&gcc GCC_PCIE0_PIPE_ARES>,
> + <&gcc GCC_PCIE0_SLEEP_ARES>,
> + <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
> + <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
> + <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
> + <&gcc GCC_PCIE0_AHB_ARES>,
> + <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
> + <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
> +
> + reset-names = "pipe",
> + "sleep",
> + "sticky",
> + "axi_m",
> + "axi_s",
> + "ahb",
> + "axi_m_sticky",
> + "axi_s_sticky";
> +
> + msi-map = <0x0 &v2m0 0x0 0xff8>;
> + status = "disabled";
> + };
> +
> };
>
> timer {
> --
> 2.34.1
>
--
மணிவண்ணன் சதாசிவம்
More information about the linux-phy
mailing list