[PATCH 4/8] arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100

[Konrad Dybcio]

On 27.08.2024 8:36 AM, Qiang Yu wrote:
> Describe PCIe3 controller and PHY. Also add required system resources like
> regulators, clocks, interrupts and registers configuration for PCIe3.
> 
> Signed-off-by: Qiang Yu <quic_qianyu at quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100.dtsi | 205 ++++++++++++++++++++++++-
>  1 file changed, 204 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index 74b694e74705..55b81e7de1c7 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -744,7 +744,7 @@ gcc: clock-controller at 100000 {
>  
>  			clocks = <&bi_tcxo_div2>,
>  				 <&sleep_clk>,
> -				 <0>,
> +				 <&pcie3_phy>,
>  				 <&pcie4_phy>,
>  				 <&pcie5_phy>,
>  				 <&pcie6a_phy>,
> @@ -2879,6 +2879,209 @@ mmss_noc: interconnect at 1780000 {
>  			#interconnect-cells = <2>;
>  		};
>  
> +		pcie3: pci at 1bd0000 {
> +			device_type = "pci";
> +			compatible = "qcom,pcie-x1e80100";
> +			reg = <0 0x01bd0000 0 0x3000>,
> +			      <0 0x78000000 0 0xf1d>,
> +			      <0 0x78000f40 0 0xa8>,
> +			      <0 0x78001000 0 0x1000>,
> +			      <0 0x78100000 0 0x100000>;
> +			reg-names = "parf",
> +				    "dbi",
> +				    "elbi",
> +				    "atu",
> +				    "config";

There's a "mhi" region at 0x01bd3000, 0x1000-wide too, please add it

> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			ranges = <0x01000000 0 0x00000000 0 0x78200000 0 0x100000>,
> +				 <0x02000000 0 0x78300000 0 0x78300000 0 0x3d00000>;

There's 64bit BAR space as well:

<0x03000000 0x7 0x40000000 0x7 0x40000000 0x0 0x40000000>;

> +			bus-range = <0 0xff>;

0x00 please

> +
> +			dma-coherent;
> +
> +			linux,pci-domain = <3>;
> +			num-lanes = <8>;
> +
> +			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi0",
> +					  "msi1",
> +					  "msi2",
> +					  "msi3",
> +					  "msi4",
> +					  "msi5",
> +					  "msi6",
> +					  "msi7";
> +
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 0 0 220 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 2 &intc 0 0 0 221 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 3 &intc 0 0 0 237 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 4 &intc 0 0 0 238 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&gcc GCC_PCIE_3_PIPE_CLK_SRC>,

We don't toggle source clocks from dt, this is upstream of the pipe
div clocks and is taken care of by the common clock framework,
please drop.

> +				 <&gcc GCC_PCIE_3_AUX_CLK>,
> +				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_3_MSTR_AXI_CLK>,
> +				 <&gcc GCC_PCIE_3_SLV_AXI_CLK>,
> +				 <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>,
> +				 <&gcc GCC_CFG_NOC_PCIE_ANOC_SOUTH_AHB_CLK>,

GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK

> +				 <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>;
> +			clock-names = "pipe_clk_src",
> +				      "aux",
> +				      "cfg",
> +				      "bus_master",
> +				      "bus_slave",
> +				      "slave_q2a",
> +				      "noc_aggr",
> +				      "cnoc_sf_axi";
> +
> +			assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>;
> +			assigned-clock-rates = <19200000>;
> +
> +			interconnects = <&pcie_south_anoc MASTER_PCIE_3 QCOM_ICC_TAG_ALWAYS
> +					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> +					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> +					 &cnoc_main SLAVE_PCIE_3 QCOM_ICC_TAG_ALWAYS>;
> +			interconnect-names = "pcie-mem",
> +					     "cpu-pcie";
> +
> +			resets = <&gcc GCC_PCIE_3_BCR>,
> +				 <&gcc GCC_PCIE_3_LINK_DOWN_BCR>;
> +			reset-names = "pci",
> +				      "link_down";
> +
> +			power-domains = <&gcc GCC_PCIE_3_GDSC>;
> +
> +			phys = <&pcie3_phy>;
> +			phy-names = "pciephy";
> +
> +			operating-points-v2 = <&pcie3_opp_table>;
> +
> +			status = "disabled";
> +
> +			pcie3_opp_table: opp-table {
> +				compatible = "operating-points-v2";
> +
> +				/* GEN 1 x1 */
> +				opp-2500000 {
> +					opp-hz = /bits/ 64 <2500000>;
> +					required-opps = <&rpmhpd_opp_low_svs>;
> +					opp-peak-kBps = <250000 1>;
> +				};
> +
> +				/* GEN 1 x2 and GEN 2 x1 */
> +				opp-5000000 {
> +					opp-hz = /bits/ 64 <5000000>;
> +					required-opps = <&rpmhpd_opp_low_svs>;
> +					opp-peak-kBps = <500000 1>;
> +				};
> +
> +				/* GEN 1 x4 and GEN 2 x2*/

Missing ' '

> +				opp-10000000 {
> +					opp-hz = /bits/ 64 <10000000>;
> +					required-opps = <&rpmhpd_opp_low_svs>;
> +					opp-peak-kBps = <1000000 1>;
> +				};
> +
> +				/* GEN 1 x8 and GEN 2 X4 */

Inconsistent capitalization, please use lowercase 'x'

[...]

> +		pcie3_phy: phy at 1be0000 {
> +			compatible = "qcom,x1e80100-qmp-gen4x8-pcie-phy";
> +			reg = <0 0x01be0000 0 0x10000>;
> +
> +			clocks = <&gcc GCC_PCIE_3_AUX_CLK>,

This clock doesn't belong here, the PHY is clocked by PHY_AUX

> +				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
> +				 <&rpmhcc RPMH_CXO_CLK>,

This is unnecessary as commented before

> +				 <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>,
> +				 <&gcc GCC_PCIE_3_PHY_AUX_CLK>,
> +				 <&gcc GCC_PCIE_3_PIPE_CLK>,
> +				 <&gcc GCC_PCIE_3_PIPEDIV2_CLK>,
> +				 <&tcsr TCSR_PCIE_8L_CLKREF_EN>;

This should be the 'ref' here

Konrad