[PATCH 3/6] phy: qcom: Introduce PCIe UNIPHY 28LP driver

[Nitheesh Sekar]

On 10/4/2023 1:43 PM, Krzysztof Kozlowski wrote:
> On 03/10/2023 14:08, Nitheesh Sekar wrote:
>> Add Qualcomm PCIe UNIPHY 28LP driver support present
>> in Qualcomm IPQ5018 SoC and the phy init sequence.
>>
>> Signed-off-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
>> ---
> ...
>
>> +static int qcom_uniphy_pcie_probe(struct platform_device *pdev)
>> +{
>> +	struct qcom_uniphy_pcie *phy;
>> +	int ret;
>> +	struct phy *generic_phy;
>> +	struct phy_provider *phy_provider;
>> +	struct device *dev = &pdev->dev;
>> +	struct device_node *np = of_node_get(dev->of_node);
>> +
>> +	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
>> +	if (!phy)
>> +		return -ENOMEM;
>> +
>> +	platform_set_drvdata(pdev, phy);
>> +	phy->dev = &pdev->dev;
>> +
>> +	phy->data = of_device_get_match_data(dev);
>> +	if (!phy->data)
>> +		return -EINVAL;
>> +
>> +	ret = qcom_uniphy_pcie_get_resources(pdev, phy);
>> +	if (ret < 0) {
>> +		dev_err(&pdev->dev, "failed to get resources: %d\n", ret);
>> +		return ret;
> Syntax is:
> return dev_err_probe()
Sure. will update it and take care of this in future.
>
>
>> +	}
>> +
>> +	ret = phy_pipe_clk_register(phy, np);
>> +	if (ret)
>> +		dev_err(&pdev->dev, "failed to register phy pipe clk\n");
>> +
>> +	generic_phy = devm_phy_create(phy->dev, NULL, &pcie_ops);
>> +	if (IS_ERR(generic_phy))
>> +		return PTR_ERR(generic_phy);
>> +
>> +	phy_set_drvdata(generic_phy, phy);
>> +	phy_provider = devm_of_phy_provider_register(phy->dev,
>> +						     of_phy_simple_xlate);
>> +	if (IS_ERR(phy_provider))
>> +		return PTR_ERR(phy_provider);
>> +
>> +	return 0;
>> +}
>> +
>> +static struct platform_driver qcom_uniphy_pcie_driver = {
>> +	.probe		= qcom_uniphy_pcie_probe,
>> +	.driver		= {
>> +		.name	= "qcom-uniphy-pcie",
>> +		.owner	= THIS_MODULE,
> Run coccinelle/coccicheck.
Sure. Will do it.
>
>> +		.of_match_table = qcom_uniphy_pcie_id_table,
>> +	},
>> +};
>> +
>> +module_platform_driver(qcom_uniphy_pcie_driver);
>> +
>> +MODULE_ALIAS("platform:qcom-uniphy-pcie");
> You should not need MODULE_ALIAS() in normal cases. If you need it,
> usually it means your device ID table is wrong.
Ok. Will remove it.

Thanks,
Nitheesh