[PATCH v6 0/7] Add JH7110 USB and USB PHY driver support
Roger Quadros
rogerq at kernel.org
Fri May 26 02:03:22 PDT 2023
On 18/05/2023 14:27, Minda Chen wrote:
> This patchset adds USB driver and USB PHY for the StarFive JH7110 SoC.
> USB work mode is peripheral and using USB 2.0 PHY in VisionFive 2 board.
> The patch has been tested on the VisionFive 2 board.
>
> This patchset should be applied after the patchset [1], [2] and [3]:
> [1] https://patchwork.kernel.org/project/linux-riscv/cover/20230518101234.143748-1-xingyu.wu@starfivetech.com/
> [2] https://patchwork.kernel.org/project/linux-clk/cover/20230512022036.97987-1-xingyu.wu@starfivetech.com
> [3] https://patchwork.kernel.org/project/linux-phy/cover/20230412084540.295411-1-changhuang.liang@starfivetech.com/
>
> This patchset is base on v6.4-rc1
>
> patch 1 is usb phy dt-binding document.
> patch 2 is Pcie PHY dt-binding document.
> patch 3 is USB 2.0 PHY driver.
> patch 4 is PCIe PHY driver.
> patch 5 is usb dt-binding document.
> patch 6 is the wrapper module driver of Cadence USB3. USB controller IP is Cadence USB3.
> patch 7 is USB device tree configuration.
>
> previous version
> ---
> version 1 patchset are split to different kernel organization. It is
> incorrect. But they were sent, and Emil sent comments. I think I should
> reserve them in cover-letter. To read the change records and previous version,
> please start with version 2.
>
> v1: https://patchwork.kernel.org/project/linux-usb/cover/20230306095212.25840-1-minda.chen@starfivetech.com/
> v2: https://patchwork.kernel.org/project/linux-usb/cover/20230308082800.3008-1-minda.chen@starfivetech.com/
> v3: https://patchwork.kernel.org/project/linux-usb/cover/20230315104411.73614-1-minda.chen@starfivetech.com/
> v4: https://patchwork.kernel.org/project/linux-usb/cover/20230406015216.27034-1-minda.chen@starfivetech.com/
> v5: https://patchwork.kernel.org/project/linux-usb/cover/20230420110052.3182-1-minda.chen@starfivetech.com/
>
> changes
> v6:
> 1. (patch 3) remove the platform remove function.
> 2. (patch 4)
> - add switch to pcie mode function.
> - remove the redundant init/exit function.
> 3. (patch 5)
> - dts split to wrapper layer and cdns node. The codes are
> like v3.
> - add cdns3 sub node dts-binding references.
> 4. (patch 6)
> For stg-syscon iomem 0x10240000 - 0x10240010 actually is belonged
> to usb, so USB contain its own registers. So do not merge the dts node.
> The codes are like v3.
> - remove the cdns3_platform_add function.
> - remove phy ops because cdns3 contain all the phy ops.
> - runtime suspend function just shutdown the clocks.
> 5. (patch 7)
> - add cdns3 subnode again.
>
> v5:
> 1. (patch 1) set correct model name and commit title.
> 2. (patch 2) change to '-item' in syscon property. change commit title.
> 3. (patch 5)
> - change to '-item' in syscon configure.
> - change commit title and doc title.
> 4. (patch 6)
> - add clk and phy deinit function
> - add clk deinit function if phy init failed.
> - coding style changes and other format changes.
>
> v4:
> 1. (patch 1) split PCIe PHY dt-binding doc to patch 2.
> 2. (patch 2) PCIe PHY add stg and sys con configuration to dt-binding doc.
> 3. (patch 3)
> - split PCIe PHY driver to patch 4.
> - replace dr_mode to phy mode in jh7110_usb2_phy.
> 4. (patch 4)
> - Makefile and Kconfig sorted by alphabet sequence.
> - Add PCIe PHY stg and syscon PHY connection configuration
> for USB 3.0.
> 5. (patch 5)
> - commit message changed.
> - merge wrapper dts node and cdns3 node in example.
> - Add interrupts, reg, phy and dr_mode in property.
> - Add reset-name in property example.
> 6. (patch 6)
> - For dts node is merged, Using platform_device_alloc and
> platform_device_add to generate cadence sub device.
> - IOMEM and IRQ resource are passed to Cadence sub device.
> - Add PHY ops process for PHY dts setting can not be passed to
> Cadence USB driver.
> - remove the stg and sys USB 3.0 PHY configuration.
> - Change the suspend clock reset and clock enable sequence.
> - Get all reset and clock resources before enable them in
> cdns_clk_rst_init.
> - commit message changed.
> 7. (patch 7)
> - merge wrapper dts node and cdns3 node in usb dts.
> - move the stg and sys USB 3.0 PHY confiuration to
> PCIe PHY dts node.
> - commit message changed.
> - Add reset-names dts.
>
> v3:
> 1. Add patch 1 - 4. Add USB PHY driver and dt-binding doc.
> USB PHY codes are moved to patch 3 and patch 4.
> 2. (patch 5)
> - USB wrapper module dts document is moved to usb directory.
> - Remove the 'dr_mode' and 'starfive,usb2-only' setting.
> - Some dts format changes. dts binding check pass.
> 3. (patch 6)
> - Remove the PHY codes.
> - Search 'dr_mode' and phy setting from Cadence subnode.
> 4. (patch 7)
> - Add USB PHY dts configurion.
> - 'dr_mode' is moved to Cadence controller submode.
>
> v2:
> 1. (patch 5) dt-binding changes. The document example is the same as dts config.
> 2. (patch 6) using dev_err_probe and syscon_regmap_lookup_by_phandle_args function. Some formats changes
> 3. (patch 7) dts nodes sorted by the address after @
>
> Minda Chen (7):
> dt-bindings: phy: Add StarFive JH7110 USB PHY
> dt-bindings: phy: Add StarFive JH7110 PCIe PHY
> phy: starfive: Add JH7110 USB 2.0 PHY driver
> phy: starfive: Add JH7110 PCIE 2.0 PHY driver
> dt-bindings: usb: Add StarFive JH7110 USB controller
> usb: cdns3: Add StarFive JH7110 USB driver
> riscv: dts: starfive: Add USB dts configuration for JH7110
>
> .../phy/starfive,jh7110-pcie-phy.yaml | 58 +++++
> .../bindings/phy/starfive,jh7110-usb-phy.yaml | 50 ++++
> .../bindings/usb/starfive,jh7110-usb.yaml | 115 ++++++++
> MAINTAINERS | 14 +
> .../jh7110-starfive-visionfive-2.dtsi | 5 +
> arch/riscv/boot/dts/starfive/jh7110.dtsi | 53 ++++
> drivers/phy/starfive/Kconfig | 21 ++
> drivers/phy/starfive/Makefile | 2 +
> drivers/phy/starfive/phy-jh7110-pcie.c | 204 +++++++++++++++
> drivers/phy/starfive/phy-jh7110-usb.c | 150 +++++++++++
> drivers/usb/cdns3/Kconfig | 11 +
> drivers/usb/cdns3/Makefile | 1 +
> drivers/usb/cdns3/cdns3-starfive.c | 246 ++++++++++++++++++
> 13 files changed, 930 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/phy/starfive,jh7110-pcie-phy.yaml
> create mode 100644 Documentation/devicetree/bindings/phy/starfive,jh7110-usb-phy.yaml
> create mode 100644 Documentation/devicetree/bindings/usb/starfive,jh7110-usb.yaml
> create mode 100644 drivers/phy/starfive/phy-jh7110-pcie.c
> create mode 100644 drivers/phy/starfive/phy-jh7110-usb.c
> create mode 100644 drivers/usb/cdns3/cdns3-starfive.c
>
For this series:
Reviewed-by: Roger Quadros <rogerq at kernel.org>
More information about the linux-phy
mailing list