[PATCH v4 3/3] usb: dwc3-meson-g12a: support OTG switch for all IP versions

Dmitry Rokosov ddrokosov at sberdevices.ru
Thu May 11 14:04:55 PDT 2023


>From now, the Amlogic A1 USB controller is capable of switching between
host and gadget modes based on the status of the OTG_ID signal or via
manual USB role change.
Previously, only the Amlogic A1 IP version did not use OTG support for
host only mode, but this is no longer applicable.
Therefore, the 'otg_switch_supported' option can now be removed as
it is no longer required.

Signed-off-by: Dmitry Rokosov <ddrokosov at sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
---
 drivers/usb/dwc3/dwc3-meson-g12a.c | 16 +++-------------
 1 file changed, 3 insertions(+), 13 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
index b282ad0e69c6..a13afdb219e8 100644
--- a/drivers/usb/dwc3/dwc3-meson-g12a.c
+++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
@@ -140,7 +140,6 @@ static const char * const meson_a1_phy_names[] = {
 struct dwc3_meson_g12a;
 
 struct dwc3_meson_g12a_drvdata {
-	bool otg_switch_supported;
 	bool otg_phy_host_port_disable;
 	struct clk_bulk_data *clks;
 	int num_clks;
@@ -189,7 +188,6 @@ static int dwc3_meson_gxl_usb_post_init(struct dwc3_meson_g12a *priv);
  */
 
 static const struct dwc3_meson_g12a_drvdata gxl_drvdata = {
-	.otg_switch_supported = true,
 	.otg_phy_host_port_disable = true,
 	.clks = meson_gxl_clocks,
 	.num_clks = ARRAY_SIZE(meson_g12a_clocks),
@@ -203,7 +201,6 @@ static const struct dwc3_meson_g12a_drvdata gxl_drvdata = {
 };
 
 static const struct dwc3_meson_g12a_drvdata gxm_drvdata = {
-	.otg_switch_supported = true,
 	.otg_phy_host_port_disable = true,
 	.clks = meson_gxl_clocks,
 	.num_clks = ARRAY_SIZE(meson_g12a_clocks),
@@ -217,7 +214,6 @@ static const struct dwc3_meson_g12a_drvdata gxm_drvdata = {
 };
 
 static const struct dwc3_meson_g12a_drvdata axg_drvdata = {
-	.otg_switch_supported = true,
 	.clks = meson_gxl_clocks,
 	.num_clks = ARRAY_SIZE(meson_gxl_clocks),
 	.phy_names = meson_a1_phy_names,
@@ -230,7 +226,6 @@ static const struct dwc3_meson_g12a_drvdata axg_drvdata = {
 };
 
 static const struct dwc3_meson_g12a_drvdata g12a_drvdata = {
-	.otg_switch_supported = true,
 	.clks = meson_g12a_clocks,
 	.num_clks = ARRAY_SIZE(meson_g12a_clocks),
 	.phy_names = meson_g12a_phy_names,
@@ -242,7 +237,6 @@ static const struct dwc3_meson_g12a_drvdata g12a_drvdata = {
 };
 
 static const struct dwc3_meson_g12a_drvdata a1_drvdata = {
-	.otg_switch_supported = false,
 	.clks = meson_a1_clocks,
 	.num_clks = ARRAY_SIZE(meson_a1_clocks),
 	.phy_names = meson_a1_phy_names,
@@ -307,7 +301,7 @@ static int dwc3_meson_g12a_usb2_init_phy(struct dwc3_meson_g12a *priv, int i,
 			U2P_R0_POWER_ON_RESET,
 			U2P_R0_POWER_ON_RESET);
 
-	if (priv->drvdata->otg_switch_supported && i == USB2_OTG_PHY) {
+	if (i == USB2_OTG_PHY) {
 		regmap_update_bits(priv->u2p_regmap[i], U2P_R0,
 				   U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS,
 				   U2P_R0_ID_PULLUP | U2P_R0_DRV_VBUS);
@@ -490,7 +484,7 @@ static int dwc3_meson_g12a_otg_mode_set(struct dwc3_meson_g12a *priv,
 {
 	int ret;
 
-	if (!priv->drvdata->otg_switch_supported || !priv->phys[USB2_OTG_PHY])
+	if (!priv->phys[USB2_OTG_PHY])
 		return -EINVAL;
 
 	if (mode == PHY_MODE_USB_HOST)
@@ -589,9 +583,6 @@ static int dwc3_meson_g12a_otg_init(struct platform_device *pdev,
 	int ret, irq;
 	struct device *dev = &pdev->dev;
 
-	if (!priv->drvdata->otg_switch_supported)
-		return 0;
-
 	if (priv->otg_mode == USB_DR_MODE_OTG) {
 		/* Ack irq before registering */
 		regmap_update_bits(priv->usb_glue_regmap, USB_R5,
@@ -841,8 +832,7 @@ static int dwc3_meson_g12a_remove(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	int i;
 
-	if (priv->drvdata->otg_switch_supported)
-		usb_role_switch_unregister(priv->role_switch);
+	usb_role_switch_unregister(priv->role_switch);
 
 	of_platform_depopulate(dev);
 
-- 
2.36.0




More information about the linux-phy mailing list