[PATCH v7 2/5] phy: qcom-m31: Introduce qcom,m31 USB phy driver
Vinod Koul
vkoul at kernel.org
Fri Aug 11 01:30:05 PDT 2023
On 10-08-23, 15:26, Varadarajan Narayanan wrote:
> Add the M31 USB2 phy driver.
>
> Signed-off-by: Varadarajan Narayanan <quic_varada at quicinc.com>
> ---
> v6:
> Kconfig:Add COMPILE_TEST and remove USB_GADGET from 'depends'
> Change 'selects' USB_PHY -> GENERIC_PHY
> Driver: Use correct headers
> const int -> unsigned int for 'nregs' in private data
> Use generic names for clk, phy in m31 phy structure
> Init register details directly instead of using macro
> Use dev_err_probe in the error paths of driver probe
> v5:
> Kconfig and Makefile:- place snippet according to sorted order
> Use generic phy instead of usb-phy
> Use ARRAY_SIZE for reg init instead of blank last entry
> Fix copyright year
>
> v4:
> Remove unused enum
> Error handling for devm_clk_get
> v1:
> Combine driver, makefile and kconfig into 1 patch
> Remove 'qscratch' region and its usage. The controller driver takes care
> of those settings
> Use compatible/data to handle ipq5332 init
> Drop the default case
> Get resources by index instead of name as there is only one resource
> Add clock
> Fix review comments in the driver
> ---
> drivers/phy/qualcomm/Kconfig | 11 ++
> drivers/phy/qualcomm/Makefile | 1 +
> drivers/phy/qualcomm/phy-qcom-m31.c | 248 ++++++++++++++++++++++++++++++++++++
> 3 files changed, 260 insertions(+)
> create mode 100644 drivers/phy/qualcomm/phy-qcom-m31.c
>
> diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
> index ced6038..d891058 100644
> --- a/drivers/phy/qualcomm/Kconfig
> +++ b/drivers/phy/qualcomm/Kconfig
> @@ -143,6 +143,17 @@ config PHY_QCOM_EUSB2_REPEATER
> PMICs. The repeater is paired with a Synopsys eUSB2 Phy
> on Qualcomm SOCs.
>
> +config PHY_QCOM_M31_USB
> + tristate "Qualcomm M31 HS PHY driver support"
> + depends on USB && (ARCH_QCOM || COMPILE_TEST)
> + select GENERIC_PHY
> + help
> + Enable this to support M31 HS PHY transceivers on Qualcomm chips
> + with DWC3 USB core. It handles PHY initialization, clock
> + management required after resetting the hardware and power
> + management. This driver is required even for peripheral only or
> + host only mode configurations.
> +
> config PHY_QCOM_USB_HS
> tristate "Qualcomm USB HS PHY module"
> depends on USB_ULPI_BUS
> diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
> index df94581..ffd609a 100644
> --- a/drivers/phy/qualcomm/Makefile
> +++ b/drivers/phy/qualcomm/Makefile
> @@ -4,6 +4,7 @@ obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
> obj-$(CONFIG_PHY_QCOM_EDP) += phy-qcom-edp.o
> obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o
> obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
> +obj-$(CONFIG_PHY_QCOM_M31_USB) += phy-qcom-m31.o
> obj-$(CONFIG_PHY_QCOM_PCIE2) += phy-qcom-pcie2.o
>
> obj-$(CONFIG_PHY_QCOM_QMP_COMBO) += phy-qcom-qmp-combo.o
> diff --git a/drivers/phy/qualcomm/phy-qcom-m31.c b/drivers/phy/qualcomm/phy-qcom-m31.c
> new file mode 100644
> index 0000000..d6a8d06
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-m31.c
> @@ -0,0 +1,248 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2014-2023, The Linux Foundation. All rights reserved.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of_platform.h>
> +#include <linux/of.h>
do you need both headers..?
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +
> +#define USB2PHY_PORT_UTMI_CTRL1 0x40
> +
> +#define USB2PHY_PORT_UTMI_CTRL2 0x44
> + #define UTMI_ULPI_SEL BIT(7)
> + #define UTMI_TEST_MUX_SEL BIT(6)
> +
> +#define HS_PHY_CTRL_REG 0x10
> + #define UTMI_OTG_VBUS_VALID BIT(20)
> + #define SW_SESSVLD_SEL BIT(28)
> +
> +#define USB_PHY_UTMI_CTRL0 0x3c
> +
> +#define USB_PHY_UTMI_CTRL5 0x50
> + #define POR_EN BIT(1)
> +
> +#define USB_PHY_HS_PHY_CTRL_COMMON0 0x54
> + #define COMMONONN BIT(7)
> + #define FSEL BIT(4)
> + #define RETENABLEN BIT(3)
> + #define FREQ_24MHZ (GENMASK(6, 6) | GENMASK(4, 4))
why not use bit :-)
> +
> +#define USB_PHY_HS_PHY_CTRL2 0x64
> + #define USB2_SUSPEND_N_SEL BIT(3)
> + #define USB2_SUSPEND_N BIT(2)
> + #define USB2_UTMI_CLK_EN BIT(1)
> +
> +#define USB_PHY_CFG0 0x94
> + #define UTMI_PHY_OVERRIDE_EN BIT(1)
> +
> +#define USB_PHY_REFCLK_CTRL 0xa0
> + #define CLKCORE BIT(1)
> +
> +#define USB2PHY_PORT_POWERDOWN 0xa4
> + #define POWER_UP BIT(0)
> + #define POWER_DOWN 0
> +
> +#define USB_PHY_FSEL_SEL 0xb8
> + #define FREQ_SEL BIT(0)
> +
> +#define USB2PHY_USB_PHY_M31_XCFGI_1 0xbc
> + #define USB2_0_TX_ENABLE BIT(2)
> +
> +#define USB2PHY_USB_PHY_M31_XCFGI_4 0xc8
> + #define HSTX_SLEW_RATE_565PS GENMASK(1, 0)
> + #define PLL_CHARGING_PUMP_CURRENT_35UA GENMASK(4, 3)
> + #define ODT_VALUE_38_02_OHM GENMASK(7, 6)
> +
> +#define USB2PHY_USB_PHY_M31_XCFGI_5 0xcc
> + #define ODT_VALUE_45_02_OHM BIT(2)
> + #define HSTX_PRE_EMPHASIS_LEVEL_0_55MA BIT(0)
> +
> +#define USB2PHY_USB_PHY_M31_XCFGI_11 0xe4
> + #define XCFG_COARSE_TUNE_NUM BIT(1)
> + #define XCFG_FINE_TUNE_NUM BIT(3)
> +
> +struct m31_phy_regs {
> + u32 off;
> + u32 val;
> + u32 delay;
> +};
> +
> +struct m31_priv_data {
> + bool ulpi_mode;
> + const struct m31_phy_regs *regs;
> + unsigned int nregs;
> +};
> +
> +struct m31_phy_regs m31_ipq5332_regs[] = {
> + { USB_PHY_CFG0, UTMI_PHY_OVERRIDE_EN, 0 },
> + { USB_PHY_UTMI_CTRL5, POR_EN, 15 },
> + { USB_PHY_FSEL_SEL, FREQ_SEL, 0 },
> + { USB_PHY_HS_PHY_CTRL_COMMON0, COMMONONN | FREQ_24MHZ | RETENABLEN, 0 },
> + { USB_PHY_UTMI_CTRL5, POR_EN, 0 },
> + { USB_PHY_HS_PHY_CTRL2, USB2_SUSPEND_N_SEL | USB2_SUSPEND_N | USB2_UTMI_CLK_EN, 0 },
> + { USB2PHY_USB_PHY_M31_XCFGI_11, XCFG_COARSE_TUNE_NUM | XCFG_FINE_TUNE_NUM, 0 },
> + { USB2PHY_USB_PHY_M31_XCFGI_4, HSTX_SLEW_RATE_565PS | PLL_CHARGING_PUMP_CURRENT_35UA |
> + ODT_VALUE_38_02_OHM, 0 },
> + { USB2PHY_USB_PHY_M31_XCFGI_1, USB2_0_TX_ENABLE, 0 },
> + { USB2PHY_USB_PHY_M31_XCFGI_5, ODT_VALUE_45_02_OHM | HSTX_PRE_EMPHASIS_LEVEL_0_55MA, 4 },
> + { USB_PHY_UTMI_CTRL5, 0x0, 0 },
> + { USB_PHY_HS_PHY_CTRL2, USB2_SUSPEND_N | USB2_UTMI_CLK_EN, 0 },
More readable way to code
USB_PHY_CFG0,
UTMI_PHY_OVERRIDE_EN,
0
and so on, makes a better read and check for errors, one line for off,
one for val and one for delay
--
`~Vinod
More information about the linux-phy
mailing list