[PATCH v14 14/15] arm64: dts: ls1088ardb: Add SFP cage

[Sean Anderson]

dpmac1 defaults to a fixed link. However, it has an SFP cage, so we can
determine more about the link (such as whether it's up/down) by
describing it. The GPIOs are part of the "QIXIS" FPGA. For now, just
model them as individual registers.

Signed-off-by: Sean Anderson <sean.anderson at seco.com>
---

(no changes since v13)

Changes in v13:
- Split off SFP addition from serdes support

 .../boot/dts/freescale/fsl-ls1088a-rdb.dts    | 51 ++++++++++++++++++-
 1 file changed, 50 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
index 391c2b8afa81..9fb1960f1258 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts
@@ -10,11 +10,27 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
+
 #include "fsl-ls1088a.dtsi"
 
 / {
 	model = "LS1088A RDB Board";
 	compatible = "fsl,ls1088a-rdb", "fsl,ls1088a";
+
+	sfp_slot: sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&sfp_i2c>;
+		los-gpios = <&los_stat 5 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&los_stat 4 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&brdcfg9 4 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&dpmac1 {
+	managed = "in-band-status";
+	pcs-handle = <&pcs1>;
+	sfp = <&sfp_slot>;
 };
 
 &dpmac2 {
@@ -170,6 +186,12 @@ rtc at 51 {
 				interrupts-extended = <&extirq 0 IRQ_TYPE_LEVEL_LOW>;
 			};
 		};
+
+		sfp_i2c: i2c at 6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
 	};
 };
 
@@ -184,8 +206,31 @@ nand at 0,0 {
 	};
 
 	fpga: board-control at 2,0 {
-		compatible = "fsl,ls1088ardb-fpga", "fsl,fpga-qixis";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,ls1088ardb-fpga", "fsl,fpga-qixis",
+			     "simple-bus";
 		reg = <0x2 0x0 0x0000100>;
+		ranges = <0x0 0x2 0x0 0x0000100>;
+
+		los_stat: gpio-controller at 1d {
+			#gpio-cells = <2>;
+			compatible = "fsl,fpga-qixis-los-stat",
+				     "ni,169445-nand-gpio";
+			reg = <0x1d 0x1>;
+			reg-names = "dat";
+			gpio-controller;
+			no-output;
+		};
+
+		brdcfg9: gpio-controller at 59 {
+			#gpio-cells = <2>;
+			compatible = "fsl,fpga-qixis-brdcfg9",
+				     "ni,169445-nand-gpio";
+			reg = <0x59 0x1>;
+			reg-names = "dat";
+			gpio-controller;
+		};
 	};
 };
 
@@ -202,6 +247,10 @@ &esdhc {
 	status = "okay";
 };
 
+&pcs_mdio1 {
+	status = "okay";
+};
+
 &pcs_mdio2 {
 	status = "okay";
 };
-- 
2.35.1.1320.gc452695387.dirty