[PATCH v5 2/5] phy: qcom-qmp-pcie: support separate tables for EP mode

Dmitry Baryshkov dmitry.baryshkov at linaro.org
Mon Sep 26 10:34:32 PDT 2022


The PCIe QMP PHY requires different programming sequences when being
used for the RC (Root Complex) or for the EP (End Point) modes. Allow
selecting the submode and thus selecting a set of PHY programming
tables.

Since the RC and EP modes share common some common init sequence, the
common sequence is kept in the main table and the sequence differences
are pushed to the extra tables.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 47 +++++++++++++++++++++---
 1 file changed, 41 insertions(+), 6 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
index dc8f0f236212..dd7911879b10 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcie.c
@@ -14,6 +14,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_address.h>
+#include <linux/phy/pcie.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/consumer.h>
@@ -1320,10 +1321,14 @@ struct qmp_phy_cfg {
 	/* Main init sequence for PHY blocks - serdes, tx, rx, pcs */
 	const struct qmp_phy_cfg_tables tables;
 	/*
-	 * Additional init sequence for PHY blocks, providing additional
-	 * register programming. Unless required it can be left omitted.
+	 * Additional init sequences for PHY blocks, providing additional
+	 * register programming. They are used for providing separate sequences
+	 * for the Root Complex and for the End Point usecases.
+	 *
+	 * If EP mode is not supported, both tables can be left empty.
 	 */
 	const struct qmp_phy_cfg_tables *tables_rc;
+	const struct qmp_phy_cfg_tables *tables_ep;
 
 	/* clock ids to be requested */
 	const char * const *clk_list;
@@ -1367,6 +1372,7 @@ struct qmp_phy_cfg {
  * @pcs_misc: iomapped memory space for lane's pcs_misc
  * @pipe_clk: pipe clock
  * @qmp: QMP phy to which this lane belongs
+ * @mode: currently selected PHY mode
  */
 struct qmp_phy {
 	struct phy *phy;
@@ -1380,6 +1386,7 @@ struct qmp_phy {
 	void __iomem *pcs_misc;
 	struct clk *pipe_clk;
 	struct qcom_qmp *qmp;
+	int mode;
 };
 
 /**
@@ -1995,13 +2002,19 @@ static int qmp_pcie_power_on(struct phy *phy)
 	struct qmp_phy *qphy = phy_get_drvdata(phy);
 	struct qcom_qmp *qmp = qphy->qmp;
 	const struct qmp_phy_cfg *cfg = qphy->cfg;
+	const struct qmp_phy_cfg_tables *mode_tables;
 	void __iomem *pcs = qphy->pcs;
 	void __iomem *status;
 	unsigned int mask, val, ready;
 	int ret;
 
+	if (qphy->mode == PHY_MODE_PCIE_RC)
+		mode_tables = cfg->tables_rc;
+	else
+		mode_tables = cfg->tables_ep;
+
 	qmp_pcie_serdes_init(qphy, &cfg->tables);
-	qmp_pcie_serdes_init(qphy, cfg->tables_rc);
+	qmp_pcie_serdes_init(qphy, mode_tables);
 
 	ret = clk_prepare_enable(qphy->pipe_clk);
 	if (ret) {
@@ -2011,10 +2024,10 @@ static int qmp_pcie_power_on(struct phy *phy)
 
 	/* Tx, Rx, and PCS configurations */
 	qmp_pcie_lanes_init(qphy, &cfg->tables);
-	qmp_pcie_lanes_init(qphy, cfg->tables_rc);
+	qmp_pcie_lanes_init(qphy, mode_tables);
 
 	qmp_pcie_pcs_init(qphy, &cfg->tables);
-	qmp_pcie_pcs_init(qphy, cfg->tables_rc);
+	qmp_pcie_pcs_init(qphy, mode_tables);
 
 	/*
 	 * Pull out PHY from POWER DOWN state.
@@ -2101,6 +2114,24 @@ static int qmp_pcie_disable(struct phy *phy)
 	return qmp_pcie_exit(phy);
 }
 
+static int qmp_pcie_set_mode(struct phy *phy,
+				 enum phy_mode mode, int submode)
+{
+	struct qmp_phy *qphy = phy_get_drvdata(phy);
+
+	switch (submode) {
+	case PHY_MODE_PCIE_RC:
+	case PHY_MODE_PCIE_EP:
+		qphy->mode = submode;
+		break;
+	default:
+		dev_err(&phy->dev, "Unuspported submode %d\n", submode);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 static int qmp_pcie_vreg_init(struct device *dev, const struct qmp_phy_cfg *cfg)
 {
 	struct qcom_qmp *qmp = dev_get_drvdata(dev);
@@ -2224,6 +2255,7 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
 static const struct phy_ops qmp_pcie_ops = {
 	.power_on	= qmp_pcie_enable,
 	.power_off	= qmp_pcie_disable,
+	.set_mode	= qmp_pcie_set_mode,
 	.owner		= THIS_MODULE,
 };
 
@@ -2239,6 +2271,8 @@ static int qmp_pcie_create(struct device *dev, struct device_node *np, int id,
 	if (!qphy)
 		return -ENOMEM;
 
+	qphy->mode = PHY_MODE_PCIE_RC;
+
 	qphy->cfg = cfg;
 	qphy->serdes = serdes;
 	/*
@@ -2282,7 +2316,8 @@ static int qmp_pcie_create(struct device *dev, struct device_node *np, int id,
 
 	if (IS_ERR(qphy->pcs_misc)) {
 		if (cfg->tables.pcs_misc ||
-		    (cfg->tables_rc && cfg->tables_rc->pcs_misc))
+		    (cfg->tables_rc && cfg->tables_rc->pcs_misc) ||
+		    (cfg->tables_ep && cfg->tables_ep->pcs_misc))
 			return PTR_ERR(qphy->pcs_misc);
 	}
 
-- 
2.35.1




More information about the linux-phy mailing list