[PATCH v7 2/5] PCI: qcom: Add retry logic for link to be stable in either L1.1 or L1.2

Krishna chaitanya chundru quic_krichai at quicinc.com
Tue Sep 20 03:22:24 PDT 2022


When link is in L1ss(L1.1 or L1.2), all the clocks will gate off and there
will be no activity on the link. At that point clocks and phy
can be turned off. If clocks got disabled before link enters
L1ss the PCIe link goes down.

Few endpoints are taking time more time to settle the link in L1 substates.
When we check the traffic in protocol analyzer, we see some DLLP packets
going on still. So Wait for max time of 200ms for the link to be stable in
L1 substates.

Signed-off-by: Krishna chaitanya chundru <quic_krichai at quicinc.com>
---
changes since v6:
	- updated comments.
---
 drivers/pci/controller/dwc/pcie-qcom.c | 46 ++++++++++++++++++++++++++--------
 1 file changed, 35 insertions(+), 11 deletions(-)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 3f5424a..7a6f69e 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -1809,23 +1809,47 @@ static int qcom_pcie_probe(struct platform_device *pdev)
 static int __maybe_unused qcom_pcie_pm_suspend(struct qcom_pcie *pcie)
 {
 	u32 val;
+	ktime_t timeout, start;
 	struct dw_pcie *pci = pcie->pci;
 	struct device *dev = pci->dev;
 
-	/* if the link is not active turn off clocks */
-	if (!dw_pcie_link_up(pci)) {
-		dev_dbg(dev, "Link is not active\n");
-		goto suspend;
-	}
+	/*
+	 * When link is in L1ss, all the clocks will gate off and
+	 * there will be no activity on the link. At that point clocks
+	 * and phy can be turned off. If clocks got disabled before
+	 * link enters L1ss the PCIe link goes down.
+	 *
+	 * Few endpoints are taking time more time to settle the link
+	 * in L1ss. Wait for max of 200ms for the link to be stable in
+	 * L1ss.
+	 */
+	start = ktime_get();
+	/* Wait max 200 ms */
+	timeout = ktime_add_ms(start, 200);
+
+	while (1) {
+		/* if the liink is not active turn off clocks */
+		if (!dw_pcie_link_up(pci)) {
+			dev_dbg(dev, "Link is not active\n");
+			break;
+		}
 
-	/* if the link is not in l1ss don't turn off clocks */
-	val = readl(pcie->parf + PCIE20_PARF_PM_STTS);
-	if (!(val & PCIE20_PARF_PM_STTS_LINKST_IN_L1SUB)) {
-		dev_warn(dev, "Link is not in L1ss\n");
-		return 0;
+		/* if the link is not in l1ss don't turn off clocks */
+		val = readl(pcie->parf + PCIE20_PARF_PM_STTS);
+		if ((val & PCIE20_PARF_PM_STTS_LINKST_IN_L1SUB)) {
+			dev_dbg(dev, "Link enters L1ss after %lld  ms\n",
+					ktime_to_ms(ktime_get() - start));
+			break;
+		}
+
+		if (ktime_after(ktime_get(), timeout)) {
+			dev_warn(dev, "Link is not in L1ss\n");
+			return 0;
+		}
+
+		udelay(1000);
 	}
 
-suspend:
 	if (pcie->cfg->ops->suspend)
 		pcie->cfg->ops->suspend(pcie);
 
-- 
2.7.4




More information about the linux-phy mailing list