[PATCH 15/20] phy: qcom-qmp-combo: drop start and pwrdn-ctrl abstraction

[Johan Hovold]

All USB PHYs need to start and stop the SerDes and PCS so drop the
start-ctrl abstraction which is no longer needed since the QMP driver
split.

Similarly, drop the pwrdn-ctrl abstraction which also is not needed
since the split.

Signed-off-by: Johan Hovold <johan+linaro at kernel.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 29 +++++------------------
 1 file changed, 6 insertions(+), 23 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index 0071c73ac1c8..2fab8d5ec0f1 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -851,9 +851,6 @@ struct qmp_phy_cfg {
 	/* array of registers with different offsets */
 	const unsigned int *regs;
 
-	unsigned int start_ctrl;
-	unsigned int pwrdn_ctrl;
-
 	/* true, if PHY needs delay after POWER_DOWN */
 	bool has_pwrdn_delay;
 
@@ -1019,9 +1016,6 @@ static const struct qmp_phy_cfg sc7180_usb3phy_cfg = {
 	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
 	.regs			= qmp_v3_usb3phy_regs_layout,
 
-	.start_ctrl		= SERDES_START | PCS_START,
-	.pwrdn_ctrl		= SW_PWRDN,
-
 	.has_pwrdn_delay	= true,
 };
 
@@ -1087,9 +1081,6 @@ static const struct qmp_phy_cfg sdm845_usb3phy_cfg = {
 	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
 	.regs			= qmp_v3_usb3phy_regs_layout,
 
-	.start_ctrl		= SERDES_START | PCS_START,
-	.pwrdn_ctrl		= SW_PWRDN,
-
 	.has_pwrdn_delay	= true,
 };
 
@@ -1121,9 +1112,6 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
 	.regs			= qmp_v4_usb3phy_regs_layout,
 	.pcs_usb_offset		= 0x300,
 
-	.start_ctrl		= SERDES_START | PCS_START,
-	.pwrdn_ctrl		= SW_PWRDN,
-
 	.has_pwrdn_delay	= true,
 };
 
@@ -1189,9 +1177,6 @@ static const struct qmp_phy_cfg sc8280xp_usb43dp_usb_cfg = {
 	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
 	.regs			= qmp_v4_usb3phy_regs_layout,
 	.pcs_usb_offset		= 0x300,
-
-	.start_ctrl		= SERDES_START | PCS_START,
-	.pwrdn_ctrl		= SW_PWRDN,
 };
 
 static const struct qmp_phy_cfg sc8280xp_usb43dp_dp_cfg = {
@@ -1259,9 +1244,6 @@ static const struct qmp_phy_cfg sm8250_usb3phy_cfg = {
 	.regs			= qmp_v4_usb3phy_regs_layout,
 	.pcs_usb_offset		= 0x300,
 
-	.start_ctrl		= SERDES_START | PCS_START,
-	.pwrdn_ctrl		= SW_PWRDN,
-
 	.has_pwrdn_delay	= true,
 };
 
@@ -1944,8 +1926,7 @@ static int qmp_combo_com_init(struct qmp_phy *qphy)
 	qphy_clrbits(dp_com, QPHY_V3_DP_COM_SWI_CTRL, 0x03);
 	qphy_clrbits(dp_com, QPHY_V3_DP_COM_SW_RESET, SW_RESET);
 
-	qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
-			cfg->pwrdn_ctrl);
+	qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRDN);
 
 	mutex_unlock(&qmp->phy_mutex);
 
@@ -2049,7 +2030,8 @@ static int qmp_combo_power_on(struct phy *phy)
 		/* Pull PHY out of reset state */
 		qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
 		/* start SerDes and Phy-Coding-Sublayer */
-		qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+		qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL],
+				SERDES_START | PCS_START);
 
 		status = pcs + cfg->regs[QPHY_PCS_STATUS];
 		ret = readl_poll_timeout(status, val, !(val & PHYSTATUS), 200,
@@ -2082,11 +2064,12 @@ static int qmp_combo_power_off(struct phy *phy)
 		qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
 
 		/* stop SerDes and Phy-Coding-Sublayer */
-		qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+		qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL],
+				SERDES_START | PCS_START);
 
 		/* Put PHY into POWER DOWN state: active low */
 		qphy_clrbits(qphy->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL],
-				cfg->pwrdn_ctrl);
+				SW_PWRDN);
 	}
 
 	return 0;
-- 
2.35.1