Oops: Machine check, sig: 7 [#1]
Batist Paklons
batist at gmail.com
Fri Apr 20 05:43:50 EDT 2007
Hi all,
I have just installed an older kernel 2.6.17 on the machine, booting
with the same reserve kernel parameter, and the card now works
perfectly.
I would like to get it to work with the 2.6.20 kernel though, the
machine is intended for someone else, who certainly does not want an
upgrade (thus reverting to 2.6.20) to break his system.
I'm only not sure if this list is still the right place to be.
Kind regards
Batist
Linux powerbookG3 2.6.17-11-powerpc #2 Tue Mar 13 22:51:22 UTC 2007
ppc GNU/Linux
dmesg output:
[ 0.000000] Using PowerMac machine description
[ 0.000000] Total memory = 192MB; using 512kB for hash table (at cbf80000)
[ 0.000000] Linux version 2.6.17-11-powerpc (root at royal) (gcc
version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 Tue
Mar 13 22:51:22 UTC 2007 (Ubuntu 2.6.17-11.37-powerpc)
[ 0.000000] Found initrd at 0xc1900000:0xc2011400
[ 0.000000] Found a Paddington mac-io controller, rev: 0, mapped at
0xfdf80000
[ 0.000000] PowerMac motherboard: PowerBook 101 (Lombard)
[ 0.000000] PMU driver v2 initialized for 1999 PowerBook G3, firmware: 0b
[ 0.000000] Found Grackle (MPC106) PCI host bridge at 0x80000000.
Firmware bus number: 0->0
[ 0.000000] nvram: OF partition at 0x140
[ 0.000000] nvram: XP partition at 0xffffffff
[ 0.000000] nvram: NR partition at 0xffffffff
[ 0.000000] Top of RAM: 0xc000000, Total RAM: 0xc000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] On node 0 totalpages: 49152
[ 0.000000] DMA zone: 49152 pages, LIFO batch:15
[ 0.000000] Built 1 zonelists
[ 0.000000] Kernel command line: root=/dev/hda3 ro
reserve=0xfd000000,0xffffff
[ 0.000000] irq: Found primary Apple PIC /pci at 80000000/mac-io at 10 for 64 irqs
[ 0.000000] irq: System has 64 possible interrupts
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] GMT Delta read from XPRAM: 0 minutes, DST: on
[ 0.000000] time_init: decrementer frequency = 16.704016 MHz
[ 0.000000] time_init: processor frequency = 399.999996 MHz
[ 25.910338] Console: colour dummy device 80x25
[ 25.911623] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 25.912659] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 25.940018] High memory: 0k
[ 25.940069] Memory: 182972k/196608k available (2748k kernel code,
13336k reserved, 432k data, 300k bss, 172k init)
[ 25.940422] Calibrating delay loop... 33.28 BogoMIPS (lpj=66560)
[ 26.022106] Security Framework v1.0.0 initialized
[ 26.022155] SELinux: Disabled at boot.
[ 26.022219] Mount-cache hash table entries: 512
[ 26.022863] device-tree: Duplicate name in /cpus/PowerPC,750 at 0,
renamed to "l2-cache#1"
[ 26.025164] checking if image is initramfs... it is
[ 28.381278] Freeing initrd memory: 7237k freed
[ 28.384574] NET: Registered protocol family 16
[ 28.385244] PMU i2c /pci at 80000000/mac-io at 10/via-pmu at 16000
[ 28.385279] channel 1 bus <multibus>
[ 28.385297] channel 2 bus <multibus>
[ 28.385642] PCI: Probing PCI hardware
[ 28.387524] PCI: Cannot allocate resource region 1 of device 0000:00:11.0
[ 28.387629] Registering pmac pic with sysfs...
[ 28.390328] NET: Registered protocol family 2
[ 28.422201] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 28.422723] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 28.423021] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 28.423180] TCP: Hash tables configured (established 8192 bind 4096)
[ 28.423201] TCP reno registered
[ 28.423311] Thermal assist unit using timers, shrink_timer: 500 jiffies
[ 28.426031] audit: initializing netlink socket (disabled)
[ 28.426116] audit(1177056265.515:1): initialized
[ 28.426624] VFS: Disk quotas dquot_6.5.1
[ 28.426731] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 28.426985] Initializing Cryptographic API
[ 28.427025] io scheduler noop registered
[ 28.427056] io scheduler anticipatory registered
[ 28.427085] io scheduler deadline registered
[ 28.427138] io scheduler cfq registered (default)
[ 28.427687] PCI: Enabling device 0000:00:11.0 (0086 -> 0087)
[ 28.427738] atyfb: using auxiliary register aperture
[ 28.428377] atyfb: 3D RAGE LT PRO (Mach64 LI, PCI) [0x4c49 rev 0xdc]
[ 28.428437] atyfb: 8M SDRAM (1:1), 29.498928 MHz XTAL, 230 MHz PLL,
100 Mhz MCLK, 100 MHz XCLK
[ 28.429016] atyfb: monitor sense=62b, mode 6
[ 28.506523] Console: switching to colour frame buffer device 128x48
[ 28.506751] atyfb: fb0: ATY Mach64 frame buffer device on PCI
[ 28.633836] Generic RTC Driver v1.07
[ 28.634254] Macintosh non-volatile memory driver v1.1
[ 28.634772] mice: PS/2 mouse device common for all mice
[ 28.637360] RAMDISK driver initialized: 16 RAM disks of 65536K size
1024 blocksize
[ 28.638391] MacIO PCI driver attached to Paddington chipset
[ 28.639570] Can't request resource 0 for MacIO device 0.00000000:power-mg
[ 28.642276] mediabay0: Registered Heathrow media-bay
[ 28.642472] mediabay0: powering down
[ 28.877987] mediabay0: switching to 3
[ 28.878126] mediabay0: powering up
[ 29.101989] mediabay0: enabling (kind:3)
[ 29.165986] mediabay0: waiting reset (kind:3)
[ 29.293985] mediabay0: waiting IDE reset (kind:3)
[ 30.445985] mediabay0: waiting IDE ready (kind:3)
[ 30.477983] mediabay0: up before IDE init
[ 30.478458] input: Macintosh mouse button emulation as /class/input/input0
[ 30.479119] Registered "pmu" backlight controller,level: 15/15
[ 30.479637] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 30.479870] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 30.480439] adb: starting probe task...
[ 31.497995] ide0: Found Apple Heathrow ATA controller, bus ID 0, irq 13
[ 31.498286] Probing IDE interface ide0...
[ 31.954183] hda: TOSHIBA MK6409MAV, ATA DISK drive
[ 32.611162] adb devices: [2]: 2 c3 [3]: 3 1 [7]: 7 1f
[ 32.634017] hda: Enabling MultiWord DMA 2
[ 32.643350] ide0 at 0xcd014000-0xcd014007,0xcd014160 on irq 13
[ 32.651679] ADB keyboard at 2, handler 1
[ 32.659820] Detected ADB keyboard, type ANSI.
[ 32.668139] input: ADB keyboard as /class/input/input1
[ 32.676483] input: ADB Powerbook buttons as /class/input/input2
[ 32.684843] Registered ide1 for media bay 0
[ 32.684864] ide1: Found Apple Heathrow ATA controller, bus ID 1
(mediabay), irq 14
[ 32.693160] Probing IDE interface ide1...
[ 32.706948] ADB mouse at 3, handler set to 4 (trackpad)
[ 32.768386] input: ADB mouse as /class/input/input3
[ 32.776545] adb: finished probe task...
[ 33.202168] hdc: MATSHITADVD-ROM SR-8171, ATAPI CD/DVD-ROM drive
[ 33.545990] hdc: Enabling MultiWord DMA 2
[ 33.555052] ide1 at 0xcd016000-0xcd016007,0xcd016160 on irq 14
[ 33.563755] PowerMac i2c bus pmu 2 registered
[ 33.572078] PowerMac i2c bus pmu 1 registered
[ 33.580489] TCP bic registered
[ 33.588579] NET: Registered protocol family 1
[ 33.596694] NET: Registered protocol family 8
[ 33.604646] NET: Registered protocol family 20
[ 33.612674] Freeing unused kernel memory: 172k init
[ 34.456492] Capability LSM initialized
[ 38.025331] usbcore: registered new driver usbfs
[ 38.035926] usbcore: registered new driver hub
[ 38.053558] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller
(OHCI) Driver (PCI)
[ 38.056730] ohci_hcd 0000:00:0e.0: OHCI Host Controller
[ 38.065119] ohci_hcd 0000:00:0e.0: new USB bus registered, assigned
bus number 1
[ 38.072482] ohci_hcd 0000:00:0e.0: irq 28, io mem 0x80882000
[ 38.165694] usb usb1: configuration #1 chosen from 1 choice
[ 38.173828] hub 1-0:1.0: USB hub found
[ 38.181343] hub 1-0:1.0: 2 ports detected
[ 38.966718] SCSI subsystem initialized
[ 38.981943] mesh: configured for synchronous 5 MB/s
[ 39.194114] mesh: performing initial bus reset...
[ 39.226978] hda: max request size: 128KiB
[ 39.430672] hda: 12685680 sectors (6495 MB), CHS=13424/15/63, (U)DMA
[ 39.438360] hda: cache flushes not supported
[ 39.445878] hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8
[ 39.499341] hdc: ATAPI 20X DVD-ROM drive, 512kB Cache, DMA
[ 39.506824] Uniform CD-ROM driver Revision: 3.20
[ 40.894858] Attempting manual resume
[ 41.110254] kjournald starting. Commit interval 5 seconds
[ 41.117765] EXT3-fs: mounted filesystem with ordered data mode.
[ 43.202049] scsi0 : MESH
[ 43.759000] eth0: BMAC+ at 00:50:e4:7a:47:51
[ 50.339589] phy registers:
[ 50.339611] 0800 7849 2000 5c10 01e1 41e1 0007 2801
[ 50.349856] 0000 0000 0000 0000 0000 0000 0000 0000
[ 50.360094] 2002 0000 0000 0000 0001 0000 0020 0000
[ 50.370333] 0000 0000 0180 0100 0006 0f00 0000 0000
[ 51.171071] ts: Compaq touchscreen protocol output
[ 55.358816] NET: Registered protocol family 17
[ 61.082760] pmac_zilog: 0.6 (Benjamin Herrenschmidt
<benh at kernel.crashing.org>)
[ 61.096348] pmac_zilog: serial modem detected
[ 61.103814] ttyS0 at MMIO 0x80813020 (irq = 15) is a Z85c30 ESCC -
Internal modem
[ 61.114230] ttyS1 at MMIO 0x80813000 (irq = 16) is a Z85c30 ESCC -
Infrared port
[ 61.863210] PCI: Enabling device 0000:00:13.0 (0000 -> 0002)
[ 61.871706] Yenta: CardBus bridge found at 0000:00:13.0 [0000:0000]
[ 61.879279] PCI: Bus 1, cardbus bridge: 0000:00:13.0
[ 61.886811] IO window: 00001400-000015ff
[ 61.894236] IO window: 00001800-000019ff
[ 61.901611] PREFETCH window: 80000000-803fffff
[ 61.909010] MEM window: 80400000-807fffff
[ 61.916384] Yenta: Enabling burst memory read transactions
[ 61.923814] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 61.931275] Yenta: Routing CardBus interrupts to PCI
[ 61.938691] Yenta TI: socket 0000:00:13.0, mfunc 0x00000002, devctl 0x60
[ 62.050028] Yenta: ISA IRQ mask 0x0000, PCI irq 22
[ 62.057634] Socket status: 30000086
[ 62.065033] pcmcia: parent PCI bridge I/O window: 0x0 - 0x7fffff
[ 62.077403] pcmcia: parent PCI bridge Memory window: 0x80000000 - 0xfcffffff
[ 62.085058] pcmcia: parent PCI bridge Memory window: 0xfd000000 - 0xfdffffff
[ 63.021055] apm_emu: APM Emulation 0.5 initialized.
[ 65.646801] input: PowerMac Beep as /class/input/input4
[ 66.559176] Adding 351552k swap on
/dev/disk/by-uuid/5de2f7e0-bb6e-49cc-b4c6-6e2fc4b74459. Priority:-1
extents:1 across:351552k
[ 67.009724] EXT3 FS on hda3, internal journal
[ 68.087955] kjournald starting. Commit interval 5 seconds
[ 68.096122] EXT3 FS on hda8, internal journal
[ 68.096147] EXT3-fs: mounted filesystem with ordered data mode.
[ 68.137367] kjournald starting. Commit interval 5 seconds
[ 68.143006] EXT3 FS on hda7, internal journal
[ 68.143030] EXT3-fs: mounted filesystem with ordered data mode.
[ 68.214561] kjournald starting. Commit interval 5 seconds
[ 68.223405] EXT3 FS on hda4, internal journal
[ 68.223428] EXT3-fs: mounted filesystem with ordered data mode.
[ 68.272234] kjournald starting. Commit interval 5 seconds
[ 68.319313] EXT3 FS on hda5, internal journal
[ 68.319352] EXT3-fs: mounted filesystem with ordered data mode.
[ 101.815690] lp: driver loaded but no devices found
[ 102.366535] ppdev: user-space parallel port driver
[ 497.941249] NET: Registered protocol family 10
[ 497.941713] lo: Disabled Privacy Extensions
[ 497.942186] IPv6 over IPv4 tunneling driver
[ 508.545547] eth0: no IPv6 routers present
[ 557.817502] pccard: PCMCIA card inserted into slot 0
[ 557.817542] cs: memory probe 0x80000000-0xfcffffff: excluding
0x80000000-0x81ffffff
[ 557.923320] cs: memory probe 0xfd000000-0xfdffffff: excluding
0xfd000000-0xfdffffff
[ 557.924033] pcmcia: registering new device pcmcia0.0
[ 558.398124] orinoco 0.15rc3 (David Gibson
<hermes at gibson.dropbear.id.au>, Pavel Roskin <proski at gnu.org>, et al)
[ 558.468212] orinoco_cs 0.15rc3 (David Gibson
<hermes at gibson.dropbear.id.au>, Pavel Roskin <proski at gnu.org>, et al)
[ 558.616419] eth1: Hardware identity 8003:0000:0001:0000
[ 558.616561] eth1: Station identity 001f:0004:0001:0003
[ 558.616573] eth1: Firmware determined as Intersil 1.3.4
[ 558.616582] eth1: Ad-hoc demo mode supported
[ 558.616590] eth1: IEEE standard IBSS ad-hoc mode supported
[ 558.616599] eth1: WEP supported, 104-bit key
[ 558.616691] eth1: MAC address 00:02:6F:01:12:B3
[ 558.616783] eth1: Station name "Prism I"
[ 558.617277] eth1: ready
[ 558.627761] eth1: index 0x01: , irq 22, io 0x0000-0x003f
[ 558.772161] ieee80211_crypt: registered algorithm 'NULL'
[ 558.884782] hostap_cs: 0.4.4-kernel (Jouni Malinen <jkmaline at cc.hut.fi>)
[ 559.121499] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 559.212347] eth1: New link status: Disconnected (0002)
[ 559.721463] eth1: New link status: Association Failed (0006)
[ 621.438345] eth1: New link status: Disconnected (0002)
[ 623.208325] eth1: New link status: Connected (0001)
[ 623.208391] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 633.569464] eth1: no IPv6 routers present
[ 646.782936] eth1: New link status: Disconnected (0002)
[ 647.596634] eth1: New link status: Connected (0001)
[ 647.781431] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 664.697386] eth1: no IPv6 routers present
On 18/04/07, Batist Paklons <batist at gmail.com> wrote:
> Hi
>
> I'm running xubuntu feisty on a powerbook G3. I've been trying to get
> a wireless pcmcia NIC to work - but to no avail:
>
> [ 196.111372] pccard: PCMCIA card inserted into slot 0
> [ 196.111407] cs: memory probe 0x80000000-0xfcffffff: excluding 0x80000000-0x81
> ffffff
> [ 196.230699] cs: memory probe 0xfd000000-0xfdffffff:Machine check in kernel mo
> de.
> [ 196.230784] Caused by (from SRR1=49030): Transfer error ack signal
> [ 196.231010] Oops: Machine check, sig: 7 [#1]
>
> I have found a similar problem in the list in this thread:
> http://lists.infradead.org/pipermail/linux-pcmcia/2006-April/003487.html
>
> Following that post I added a kernel parameter:
> [ 0.000000] Kernel command line: root=/dev/hda3 ro reserve=0xfd000000,0xfffff
> f
> but still the same error occurs. Where did I go wrong?
>
> I've added a bunch of useful stuff such as dmesg (the card was
> inserted after starting up, the error message is right at the end).
>
> Thanks in advance!
> Batist
>
> Linux powerbookG3 2.6.20-15-powerpc #3 Sun Apr 15 06:45:49 UTC 2007
> ppc GNU/Linux
>
> dmesg
> [ 0.000000] Using PowerMac machine description
> [ 0.000000] Total memory = 192MB; using 512kB for hash table (at cbf80000)
> [ 0.000000] Linux version 2.6.20-15-powerpc (root at adare) (gcc
> version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #3 Sun Apr 15 06:45:49 UTC 2007
> (Ubuntu 2.6.20-15.27-powerpc)
> [ 0.000000] Found initrd at 0xc1900000:0xc204b400
> [ 0.000000] Found a Paddington mac-io controller, rev: 0, mapped at
> 0xfdf80000
> [ 0.000000] PowerMac motherboard: PowerBook 101 (Lombard)
> [ 0.000000] PMU driver v2 initialized for 1999 PowerBook G3, firmware: 0b
> [ 0.000000] Entering add_active_range(0, 0, 49152) 0 entries of 256 used
> [ 0.000000] Found Grackle (MPC106) PCI host bridge at
> 0x0000000080000000. Firmware bus number: 0->0
> [ 0.000000] nvram: OF partition at 0x140
> [ 0.000000] nvram: XP partition at 0xffffffff
> [ 0.000000] nvram: NR partition at 0xffffffff
> [ 0.000000] Top of RAM: 0xc000000, Total RAM: 0xc000000
> [ 0.000000] Memory hole size: 0MB
> [ 0.000000] Zone PFN ranges:
> [ 0.000000] DMA 0 -> 49152
> [ 0.000000] Normal 49152 -> 49152
> [ 0.000000] HighMem 49152 -> 49152
> [ 0.000000] early_node_map[1] active PFN ranges
> [ 0.000000] 0: 0 -> 49152
> [ 0.000000] On node 0 totalpages: 49152
> [ 0.000000] DMA zone: 384 pages used for memmap
> [ 0.000000] DMA zone: 0 pages reserved
> [ 0.000000] DMA zone: 48768 pages, LIFO batch:15
> [ 0.000000] Normal zone: 0 pages used for memmap
> [ 0.000000] HighMem zone: 0 pages used for memmap
> [ 0.000000] Built 1 zonelists. Total pages: 48768
> [ 0.000000] Kernel command line: root=/dev/hda3 ro
> reserve=0xfd000000,0xffffff
> [ 0.000000] irq: Found primary Apple PIC /pci at 80000000/mac-io at 10 for 64 irqs
> [ 0.000000] irq: System has 64 possible interrupts
> [ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
> [ 0.000000] GMT Delta read from XPRAM: 0 minutes, DST: on
> [ 0.000000] time_init: decrementer frequency = 16.703983 MHz
> [ 0.000000] time_init: processor frequency = 399.999996 MHz
> [ 26.038132] Console: colour dummy device 80x25
> [ 26.039439] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> [ 26.040476] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> [ 26.067581] High memory: 0k
> [ 26.067598] Memory: 182528k/196608k available (3220k kernel code,
> 13744k reserved, 120k data, 293k bss, 188k init)
> [ 26.068022] Calibrating delay loop... 33.28 BogoMIPS (lpj=66560)
> [ 26.149873] Security Framework v1.0.0 initialized
> [ 26.149926] SELinux: Disabled at boot.
> [ 26.149995] Mount-cache hash table entries: 512
> [ 26.150644] device-tree: Duplicate name in /cpus/PowerPC,750 at 0,
> renamed to "l2-cache#1"
> [ 26.153881] NET: Registered protocol family 16
> [ 26.154549] PMU i2c /pci at 80000000/mac-io at 10/via-pmu at 16000
> [ 26.154580] channel 1 bus <multibus>
> [ 26.154598] channel 2 bus <multibus>
> [ 26.154738] PCI: Probing PCI hardware
> [ 26.156754] PCI: Cannot allocate resource region 1 of device 0000:00:11.0
> [ 26.156849] Registering pmac pic with sysfs...
> [ 26.160793] NET: Registered protocol family 8
> [ 26.160822] NET: Registered protocol family 20
> [ 26.162213] NET: Registered protocol family 2
> [ 26.197932] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
> [ 26.198294] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
> [ 26.198541] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> [ 26.198687] TCP: Hash tables configured (established 8192 bind 4096)
> [ 26.198709] TCP reno registered
> [ 26.210210] checking if image is initramfs... it is
> [ 28.615371] Freeing initrd memory: 7469k freed
> [ 28.617004] Thermal assist unit using timers, shrink_timer: 500 jiffies
> [ 28.618494] audit: initializing netlink socket (disabled)
> [ 28.618585] audit(1176920167.580:1): initialized
> [ 28.619082] VFS: Disk quotas dquot_6.5.1
> [ 28.619208] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [ 28.619506] io scheduler noop registered
> [ 28.619534] io scheduler anticipatory registered
> [ 28.619554] io scheduler deadline registered
> [ 28.619597] io scheduler cfq registered (default)
> [ 28.620652] PCI: Enabling device 0000:00:11.0 (0086 -> 0087)
> [ 28.620713] atyfb: using auxiliary register aperture
> [ 28.621346] atyfb: 3D RAGE LT PRO (Mach64 LI, PCI) [0x4c49 rev 0xdc]
> [ 28.621407] atyfb: 8M SDRAM (1:1), 29.498928 MHz XTAL, 230 MHz PLL,
> 100 Mhz MCLK, 100 MHz XCLK
> [ 28.621989] atyfb: monitor sense=62b, mode 6
> [ 28.685979] Console: switching to colour frame buffer device 128x48
> [ 28.705901] atyfb: fb0: ATY Mach64 frame buffer device on PCI
> [ 28.857512] Generic RTC Driver v1.07
> [ 28.857997] Macintosh non-volatile memory driver v1.1
> [ 28.858614] mice: PS/2 mouse device common for all mice
> [ 28.861517] RAMDISK driver initialized: 16 RAM disks of 65536K size
> 1024 blocksize
> [ 28.862592] MacIO PCI driver attached to Paddington chipset
> [ 28.863931] Can't request resource 0 for MacIO device 0.00000000:power-mg
> [ 28.867185] mediabay0: Registered Heathrow media-bay
> [ 28.867418] mediabay0: powering down
> [ 29.101680] mediabay0: switching to 3
> [ 29.101837] mediabay0: powering up
> [ 29.325678] mediabay0: enabling (kind:3)
> [ 29.389674] mediabay0: waiting reset (kind:3)
> [ 29.517671] mediabay0: waiting IDE reset (kind:3)
> [ 30.669655] mediabay0: waiting IDE ready (kind:3)
> [ 30.701654] mediabay0: up before IDE init
> [ 30.702187] input: Macintosh mouse button emulation as /class/input/input0
> [ 30.703214] pmubl: Backlight initialized (pmubl)
> [ 30.703626] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> [ 30.703892] ide: Assuming 33MHz system bus speed for PIO modes;
> override with idebus=xx
> [ 30.704483] adb: starting probe task...
> [ 31.721652] ide0: Found Apple Heathrow ATA controller, bus ID 0, irq 20
> [ 31.721971] Probing IDE interface ide0...
> [ 32.177837] hda: TOSHIBA MK6409MAV, ATA DISK drive
> [ 32.831125] adb devices: [2]: 2 c3 [3]: 3 1 [7]: 7 1f
> [ 32.856981] ADB keyboard at 2, handler 1
> [ 32.866098] Detected ADB keyboard, type ANSI.
> [ 32.875370] input: ADB keyboard as /class/input/input1
> [ 32.884642] input: ADB Powerbook buttons as /class/input/input2
> [ 32.893677] hda: Enabling MultiWord DMA 2
> [ 32.903665] ide0 at 0xcd012000-0xcd012007,0xcd012160 on irq 20
> [ 32.913237] Registered ide1 for media bay 0
> [ 32.913258] ide1: Found Apple Heathrow ATA controller, bus ID 1
> (mediabay), irq 31
> [ 32.922617] Probing IDE interface ide1...
> [ 32.931262] ADB mouse at 3, handler set to 4 (trackpad)
> [ 32.994257] input: ADB mouse as /class/input/input3
> [ 33.003443] adb: finished probe task...
> [ 33.401806] hdc: MATSHITADVD-ROM SR-8171, ATAPI CD/DVD-ROM drive
> [ 33.745621] hdc: Enabling MultiWord DMA 2
> [ 33.755698] ide1 at 0xcd018000-0xcd018007,0xcd018160 on irq 31
> [ 33.765412] PowerMac i2c bus pmu 2 registered
> [ 33.774661] PowerMac i2c bus pmu 1 registered
> [ 33.784043] TCP cubic registered
> [ 33.793047] NET: Registered protocol family 1
> [ 33.802270] Freeing unused kernel memory: 188k init
> [ 34.664163] Capability LSM initialized
> [ 38.447109] usbcore: registered new interface driver usbfs
> [ 38.447589] usbcore: registered new interface driver hub
> [ 38.447958] usbcore: registered new device driver usb
> [ 38.454521] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
> (OHCI) Driver
> [ 38.454718] ohci_hcd 0000:00:0e.0: OHCI Host Controller
> [ 38.455604] ohci_hcd 0000:00:0e.0: new USB bus registered, assigned
> bus number 1
> [ 38.456008] ohci_hcd 0000:00:0e.0: irq 28, io mem 0x80882000
> [ 38.639470] usb usb1: configuration #1 chosen from 1 choice
> [ 38.639953] hub 1-0:1.0: USB hub found
> [ 38.640203] hub 1-0:1.0: 2 ports detected
> [ 39.237886] SCSI subsystem initialized
> [ 39.245662] mesh: configured for synchronous 5 MB/s
> [ 39.449782] mesh: performing initial bus reset...
> [ 39.844696] hda: max request size: 128KiB
> [ 40.042244] hda: 12685680 sectors (6495 MB), CHS=13424/15/63, (U)DMA
> [ 40.042711] hda: cache flushes not supported
> [ 40.043104] hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8
> [ 40.203217] hdc: ATAPI 20X DVD-ROM drive, 512kB Cache, DMA
> [ 40.203702] Uniform CD-ROM driver Revision: 3.20
> [ 41.374431] Attempting manual resume
> [ 41.548016] kjournald starting. Commit interval 5 seconds
> [ 41.548450] EXT3-fs: mounted filesystem with ordered data mode.
> [ 43.453569] scsi0 : MESH
> [ 44.003875] eth0: BMAC+ at 00:50:e4:7a:47:51
> [ 49.460579] phy registers:
> [ 49.460599] 0800 7849 2000 5c10 01e1 41e1 0007 2801
> [ 49.470965] 0000 0000 0000 0000 0000 0000 0000 0000
> [ 49.481324] 2002 0000 0000 0000 0001 0000 0020 0000
> [ 49.491685] 0000 0000 0180 0100 0006 0f00 0000 0000
> [ 54.134269] NET: Registered protocol family 17
> [ 57.029251] PCI: Enabling device 0000:00:13.0 (0000 -> 0002)
> [ 57.029720] Yenta: CardBus bridge found at 0000:00:13.0 [0000:0000]
> [ 57.030038] PCI: Bus 1, cardbus bridge: 0000:00:13.0
> [ 57.030265] IO window: 00001400-000015ff
> [ 57.030459] IO window: 00001800-000019ff
> [ 57.030653] PREFETCH window: 80000000-803fffff
> [ 57.030867] MEM window: 80400000-807fffff
> [ 57.031066] Yenta: Enabling burst memory read transactions
> [ 57.031312] Yenta: Using CSCINT to route CSC interrupts to PCI
> [ 57.031567] Yenta: Routing CardBus interrupts to PCI
> [ 57.031791] Yenta TI: socket 0000:00:13.0, mfunc 0x00000002, devctl 0x60
> [ 57.133371] Yenta: ISA IRQ mask 0x0000, PCI irq 22
> [ 57.133697] Socket status: 30000006
> [ 57.133871] pcmcia: parent PCI bridge I/O window: 0x0 - 0x7fffff
> [ 57.134140] pcmcia: parent PCI bridge Memory window: 0x80000000 - 0xfcffffff
> [ 57.134443] pcmcia: parent PCI bridge Memory window: 0xfd000000 - 0xfdffffff
> [ 62.931940] pmac_zilog: 0.6 (Benjamin Herrenschmidt
> <benh at kernel.crashing.org>)
> [ 62.939055] pmac_zilog: serial modem detected
> [ 62.939539] ttyS0 at MMIO 0x80813020 (irq = 35) is a Z85c30 ESCC -
> Internal modem
> [ 62.948488] ttyS1 at MMIO 0x80813000 (irq = 38) is a Z85c30 ESCC -
> Infrared port
> [ 63.519859] apm_emu: APM Emulation 0.5 initialized.
> [ 66.254320] input: PowerMac Beep as /class/input/input4
> [ 67.170934] Adding 351552k swap on
> /dev/disk/by-uuid/5de2f7e0-bb6e-49cc-b4c6-6e2fc4b74459. Priority:-1
> extents:1 across:351552k
> [ 67.564338] EXT3 FS on hda3, internal journal
> [ 68.528530] kjournald starting. Commit interval 5 seconds
> [ 68.529919] EXT3 FS on hda8, internal journal
> [ 68.529942] EXT3-fs: mounted filesystem with ordered data mode.
> [ 68.563591] kjournald starting. Commit interval 5 seconds
> [ 68.564666] EXT3 FS on hda7, internal journal
> [ 68.564689] EXT3-fs: mounted filesystem with ordered data mode.
> [ 68.626515] kjournald starting. Commit interval 5 seconds
> [ 68.627792] EXT3 FS on hda4, internal journal
> [ 68.627813] EXT3-fs: mounted filesystem with ordered data mode.
> [ 68.669914] kjournald starting. Commit interval 5 seconds
> [ 68.694117] EXT3 FS on hda5, internal journal
> [ 68.694140] EXT3-fs: mounted filesystem with ordered data mode.
> [ 103.388928] lp: driver loaded but no devices found
> [ 106.150040] ppdev: user-space parallel port driver
> [ 196.111372] pccard: PCMCIA card inserted into slot 0
> [ 196.111407] cs: memory probe 0x80000000-0xfcffffff: excluding
> 0x80000000-0x81ffffff
> [ 196.230699] cs: memory probe 0xfd000000-0xfdffffff:Machine check in
> kernel mode.
> [ 196.230784] Caused by (from SRR1=49030): Transfer error ack signal
> [ 196.231010] Oops: Machine check, sig: 7 [#1]
> [ 196.231316]
> [ 196.231408] Modules linked in: ppdev lp parport cpufreq_userspace
> cpufreq_stats cpufreq_powersave cpufreq_ondemand cpufreq_conservative
> snd_powermac snd_pcm_oss snd_pcm snd_mixer_oss snd_seq_dummy
> snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq
> snd_timer snd_seq_device snd soundcore snd_page_alloc apm_emu
> pmac_zilog serial_core pcmcia yenta_socket rsrc_nonstatic pcmcia_core
> af_packet tsdev evdev ext3 jbd mbcache ide_cd cdrom ide_disk bmac mesh
> scsi_mod ohci_hcd usbcore capability commoncap
> [ 196.234132] NIP: CD8ECD18 LR: CD8ECCEC CTR: C0014B88
> [ 196.234360] REGS: cbe27c80 TRAP: 0200 Not tainted (2.6.20-15-powerpc)
> [ 196.234646] MSR: 00049030 <EE,ME,IR,DR> CR: 82004024 XER: 00000000
> [ 196.235026] TASK = c1f15870[3057] 'pccardd' THREAD: cbe26000
> [ 196.235248] GPR00: 000000FF CBE27D30 C1F15870 CD990000 CD8A8014
> 00000070 00000002 CBE27D89
> [ 196.235721] GPR08: CD8A8040 00001000 CD990000 CD991000 22000022
> 00000000 00000000 FD000000
> [ 196.236194] GPR16: CD880000 FD100000 FE000000 FD000000 00200000
> CB8A1428 FD080000 000004FB
> [ 196.236668] GPR24: CBE27D89 00000000 00000002 CB8A1428 00000021
> 00000000 00000002 CBE27D89
> [ 196.237172] NIP [CD8ECD18] pcmcia_read_cis_mem+0x178/0x26c [pcmcia_core]
> [ 196.237540] LR [CD8ECCEC] pcmcia_read_cis_mem+0x14c/0x26c [pcmcia_core]
> [ 196.237854] Call Trace:
> [ 196.237984] [CBE27D30] [CD8ECCEC] pcmcia_read_cis_mem+0x14c/0x26c
> [pcmcia_core] (unreliable)
> [ 196.238390] [CBE27D60] [CD8ECF74] read_cis_cache+0x168/0x16c [pcmcia_core]
> [ 196.238721] [CBE27D80] [CD8ED1CC] pccard_get_next_tuple+0x1b0/0x480
> [pcmcia_core]
> [ 196.239076] [CBE27DC0] [CD8ED534] pccard_get_first_tuple+0x98/0x144
> [pcmcia_core]
> [ 196.239431] [CBE27DF0] [CD8EDB84] pccard_validate_cis+0xa0/0x230
> [pcmcia_core]
> [ 196.239775] [CBE27E20] [CD881EBC] readable+0x54/0xd8 [rsrc_nonstatic]
> [ 196.240094] [CBE27E40] [CD8821E8]
> pcmcia_nonstatic_validate_mem+0x16c/0x408 [rsrc_nonstatic]
> [ 196.240475] [CBE27EC0] [CD8EDD3C] pcmcia_validate_mem+0x28/0x40 [pcmcia_core]
> [ 196.240817] [CBE27ED0] [CD9227FC] pcmcia_card_add+0x40/0xd0 [pcmcia]
> [ 196.241157] [CBE27F40] [CD922934] ds_event+0xa8/0xd4 [pcmcia]
> [ 196.241443] [CBE27F60] [CD8EA4F8] send_event+0x6c/0x94 [pcmcia_core]
> [ 196.241757] [CBE27F70] [CD8EAA98] socket_insert+0xbc/0x130 [pcmcia_core]
> [ 196.242081] [CBE27F80] [CD8EB164] pccardd+0x260/0x2b0 [pcmcia_core]
> [ 196.242389] [CBE27FC0] [C0046968] kthread+0xc0/0xfc
> [ 196.242647] [CBE27FF0] [C0014434] kernel_thread+0x44/0x60
> [ 196.242912] Instruction dump:
> [ 196.243071] 4bfffd91 2c030000 41820104 813b00ec 3809ffff 7d634a14
> 7c00e838 7d430214
> [ 196.243520] 7f8b5000 419e006c 7c0004ac 7c0300ae <0c000000> 4c00012c
> 3bdeffff 981f0000
>
> lspci
> 00:00.0 Host bridge: Motorola MPC106 [Grackle] (rev 40)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0, Cache Line Size: 32 bytes
>
> 00:0e.0 USB Controller: Agere Systems USB (rev 12) (prog-if 10 [OHCI])
> Subsystem: Agere Systems USB
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (750ns min, 21500ns max)
> Interrupt: pin A routed to IRQ 28
> Region 0: Memory at 80882000 (32-bit, non-prefetchable) [size=4K]
>
> 00:0f.0 Multimedia controller: C-Cube Microsystems Cinemaster C 3.0
> DVD Decoder (rev 02)
> Subsystem: C-Cube Microsystems Cinemaster C 3.0 DVD Decoder
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (1000ns min, 32000ns max)
> Interrupt: pin A routed to IRQ 26
> Region 0: I/O ports at 0c00 [size=256]
> Capabilities: [60] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:10.0 Class ff00: Apple Computer Inc. Paddington Mac I/O
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32, Cache Line Size: 32 bytes
> Region 0: Memory at 80800000 (32-bit, non-prefetchable) [size=512K]
>
> 00:11.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro
> (rev dc) (prog-if 00 [VGA])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping+ SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2000ns min), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 24
> Region 0: Memory at 81000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: I/O ports at 1000 [size=256]
> Region 2: Memory at 80881000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [5c] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:13.0 CardBus bridge: Texas Instruments PCI1211
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 168, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 22
> Region 0: Memory at 80880000 (32-bit, non-prefetchable) [size=4K]
> Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
> Memory window 0: 80000000-803ff000 (prefetchable)
> Memory window 1: 80400000-807ff000
> I/O window 0: 00001400-000015ff
> I/O window 1: 00001800-000019ff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
> 16-bit legacy interface ports at 0001
>
> /proc/ioports
> 00000000-007fffff : /pci at 80000000
> 00000c00-00000cff : 0000:00:0f.0
> 00001000-000010ff : 0000:00:11.0
> 00001400-000015ff : PCI CardBus #01
> 00001800-000019ff : PCI CardBus #01
>
> /proc/iomem
> 80000000-fcffffff : /pci at 80000000
> 80000000-803fffff : PCI CardBus #01
> 80400000-807fffff : PCI CardBus #01
> 80800000-8087ffff : 0000:00:10.0
> 80800000-8087ffff : 0.80800000:mac-io
> 80800010-8080002f : 0.00000010:interrup
> 80800034-80800034 : 0.00000034:media-ba
> 80800034-80800034 : media-bay
> 80808000-808080ff : 0.00010000:scsi
> 80808000-808080ff : mesh
> 80808100-808081ff : 0.00015000:fdc
> 80808200-808082ff : 0.00011000:ethernet
> 80808200-808082ff : bmac
> 80808300-808083ff : 0.00011000:ethernet
> 80808300-808083ff : bmac
> 80808800-808088ff : 0.00014000:davbus
> 80808800-808088ff : Sound Tx DMA
> 80808900-808089ff : 0.00014000:davbus
> 80808900-808089ff : Sound Rx DMA
> 80808b00-80808bff : 0.00020000:ata-3
> 80808b00-80808bff : ide-pmac (dma)
> 80808c00-80808cff : 0.00021000:ata-3
> 80808c00-80808cff : ide-pmac (dma)
> 80810000-80810fff : 0.00010000:scsi
> 80810000-80810fff : mesh
> 80811000-80811fff : 0.00011000:ethernet
> 80811000-80811fff : bmac
> 80813000-80813000 : 0.00013000:ch-b
> 80813000-80813000 : pmac_zilog
> 80813010-80813010 : 0.00013000:ch-b
> 80813010-80813010 : pmac_zilog
> 80813020-80813020 : 0.00013020:ch-a
> 80813020-80813020 : pmac_zilog
> 80813030-80813030 : 0.00013020:ch-a
> 80813030-80813030 : pmac_zilog
> 80813040-80813040 : 0.00013000:ch-b
> 80813040-80813040 : pmac_zilog
> 80813050-80813050 : 0.00013020:ch-a
> 80813050-80813050 : pmac_zilog
> 80814000-80814fff : 0.00014000:davbus
> 80814000-80814fff : Sound Control
> 80815000-80815fff : 0.00015000:fdc
> 80816000-80817fff : 0.00016000:via-pmu
> 80820000-80820fff : 0.00020000:ata-3
> 80820000-80820fff : ide-pmac (ports)
> 80821000-80821fff : 0.00021000:ata-3
> 80821000-80821fff : ide-pmac (ports)
> 80880000-80880fff : 0000:00:13.0
> 80880000-80880fff : yenta_socket
> 80881000-80881fff : 0000:00:11.0
> 80881000-80881fff : atyfb
> 80882000-80882fff : 0000:00:0e.0
> 80882000-80882fff : ohci_hcd
> 81000000-81ffffff : 0000:00:11.0
> 81000000-81ffffff : atyfb
> fd000000-fdffffff : /pci at 80000000
> fd000000-fd07ffff : cs memory probe
> fd080000-fd0fffff : cs memory probe
> fffffffffd000000-fffffffffdfffffe : reserved
>
> /proc/interrupts
> CPU0
> 16: 19 PMAC-PIC Edge PMac Output
> 17: 1 PMAC-PIC Edge PMac
> 18: 107321 PMAC-PIC Edge VIA-PMU
> 19: 0 PMAC-PIC Edge PMac Input
> 20: 10297 PMAC-PIC Edge ide0
> 22: 2 PMAC-PIC Level yenta
> 23: 14 PMAC-PIC Edge MESH
> 28: 2 PMAC-PIC Level ohci_hcd:usb1
> 31: 16703 PMAC-PIC Edge ide1
> 32: 927 PMAC-PIC Edge BMAC-txdma
> 33: 1108 PMAC-PIC Edge BMAC-rxdma
> 42: 2100 PMAC-PIC Edge BMAC-misc
> BAD: 0
>
> /etc/pcmcia/config.opts
> #
> # Local PCMCIA Configuration File
> #
> #----------------------------------------------------------------------
> #
> # System resources available for PCMCIA cards
> #
> # NOTE: these settings have no effect on resources assigned to a
> # CardBus bridge device itself; this file only affects resources
> # assigned to cards. Also, interrupt settings here will only affect
> # ISA bus interrupts assigned to 16-bit cards. PCI interrupts
> # generally can't be reconfigured.
> #
> # With the kernel PCMCIA subsystem, these settings also have no effect
> # at all on resources used for 32-bit CardBus cards. Those are set by
> # the PCI hotplug subsystem.
> #
>
> include port 0x100-0x4ff
> include port 0x1000-0x17ff
> include memory 0x80000000-0x80ffffff
>
More information about the linux-pcmcia
mailing list