Oops: Machine check, sig: 7 [#1]
Batist Paklons
batist at gmail.com
Wed Apr 18 14:50:04 EDT 2007
Hi
I'm running xubuntu feisty on a powerbook G3. I've been trying to get
a wireless pcmcia NIC to work - but to no avail:
[ 196.111372] pccard: PCMCIA card inserted into slot 0
[ 196.111407] cs: memory probe 0x80000000-0xfcffffff: excluding 0x80000000-0x81
ffffff
[ 196.230699] cs: memory probe 0xfd000000-0xfdffffff:Machine check in kernel mo
de.
[ 196.230784] Caused by (from SRR1=49030): Transfer error ack signal
[ 196.231010] Oops: Machine check, sig: 7 [#1]
I have found a similar problem in the list in this thread:
http://lists.infradead.org/pipermail/linux-pcmcia/2006-April/003487.html
Following that post I added a kernel parameter:
[ 0.000000] Kernel command line: root=/dev/hda3 ro reserve=0xfd000000,0xfffff
f
but still the same error occurs. Where did I go wrong?
I've added a bunch of useful stuff such as dmesg (the card was
inserted after starting up, the error message is right at the end).
Thanks in advance!
Batist
Linux powerbookG3 2.6.20-15-powerpc #3 Sun Apr 15 06:45:49 UTC 2007
ppc GNU/Linux
dmesg
[ 0.000000] Using PowerMac machine description
[ 0.000000] Total memory = 192MB; using 512kB for hash table (at cbf80000)
[ 0.000000] Linux version 2.6.20-15-powerpc (root at adare) (gcc
version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #3 Sun Apr 15 06:45:49 UTC 2007
(Ubuntu 2.6.20-15.27-powerpc)
[ 0.000000] Found initrd at 0xc1900000:0xc204b400
[ 0.000000] Found a Paddington mac-io controller, rev: 0, mapped at
0xfdf80000
[ 0.000000] PowerMac motherboard: PowerBook 101 (Lombard)
[ 0.000000] PMU driver v2 initialized for 1999 PowerBook G3, firmware: 0b
[ 0.000000] Entering add_active_range(0, 0, 49152) 0 entries of 256 used
[ 0.000000] Found Grackle (MPC106) PCI host bridge at
0x0000000080000000. Firmware bus number: 0->0
[ 0.000000] nvram: OF partition at 0x140
[ 0.000000] nvram: XP partition at 0xffffffff
[ 0.000000] nvram: NR partition at 0xffffffff
[ 0.000000] Top of RAM: 0xc000000, Total RAM: 0xc000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 49152
[ 0.000000] Normal 49152 -> 49152
[ 0.000000] HighMem 49152 -> 49152
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 49152
[ 0.000000] On node 0 totalpages: 49152
[ 0.000000] DMA zone: 384 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 48768 pages, LIFO batch:15
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Built 1 zonelists. Total pages: 48768
[ 0.000000] Kernel command line: root=/dev/hda3 ro
reserve=0xfd000000,0xffffff
[ 0.000000] irq: Found primary Apple PIC /pci at 80000000/mac-io at 10 for 64 irqs
[ 0.000000] irq: System has 64 possible interrupts
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] GMT Delta read from XPRAM: 0 minutes, DST: on
[ 0.000000] time_init: decrementer frequency = 16.703983 MHz
[ 0.000000] time_init: processor frequency = 399.999996 MHz
[ 26.038132] Console: colour dummy device 80x25
[ 26.039439] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 26.040476] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 26.067581] High memory: 0k
[ 26.067598] Memory: 182528k/196608k available (3220k kernel code,
13744k reserved, 120k data, 293k bss, 188k init)
[ 26.068022] Calibrating delay loop... 33.28 BogoMIPS (lpj=66560)
[ 26.149873] Security Framework v1.0.0 initialized
[ 26.149926] SELinux: Disabled at boot.
[ 26.149995] Mount-cache hash table entries: 512
[ 26.150644] device-tree: Duplicate name in /cpus/PowerPC,750 at 0,
renamed to "l2-cache#1"
[ 26.153881] NET: Registered protocol family 16
[ 26.154549] PMU i2c /pci at 80000000/mac-io at 10/via-pmu at 16000
[ 26.154580] channel 1 bus <multibus>
[ 26.154598] channel 2 bus <multibus>
[ 26.154738] PCI: Probing PCI hardware
[ 26.156754] PCI: Cannot allocate resource region 1 of device 0000:00:11.0
[ 26.156849] Registering pmac pic with sysfs...
[ 26.160793] NET: Registered protocol family 8
[ 26.160822] NET: Registered protocol family 20
[ 26.162213] NET: Registered protocol family 2
[ 26.197932] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 26.198294] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 26.198541] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 26.198687] TCP: Hash tables configured (established 8192 bind 4096)
[ 26.198709] TCP reno registered
[ 26.210210] checking if image is initramfs... it is
[ 28.615371] Freeing initrd memory: 7469k freed
[ 28.617004] Thermal assist unit using timers, shrink_timer: 500 jiffies
[ 28.618494] audit: initializing netlink socket (disabled)
[ 28.618585] audit(1176920167.580:1): initialized
[ 28.619082] VFS: Disk quotas dquot_6.5.1
[ 28.619208] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 28.619506] io scheduler noop registered
[ 28.619534] io scheduler anticipatory registered
[ 28.619554] io scheduler deadline registered
[ 28.619597] io scheduler cfq registered (default)
[ 28.620652] PCI: Enabling device 0000:00:11.0 (0086 -> 0087)
[ 28.620713] atyfb: using auxiliary register aperture
[ 28.621346] atyfb: 3D RAGE LT PRO (Mach64 LI, PCI) [0x4c49 rev 0xdc]
[ 28.621407] atyfb: 8M SDRAM (1:1), 29.498928 MHz XTAL, 230 MHz PLL,
100 Mhz MCLK, 100 MHz XCLK
[ 28.621989] atyfb: monitor sense=62b, mode 6
[ 28.685979] Console: switching to colour frame buffer device 128x48
[ 28.705901] atyfb: fb0: ATY Mach64 frame buffer device on PCI
[ 28.857512] Generic RTC Driver v1.07
[ 28.857997] Macintosh non-volatile memory driver v1.1
[ 28.858614] mice: PS/2 mouse device common for all mice
[ 28.861517] RAMDISK driver initialized: 16 RAM disks of 65536K size
1024 blocksize
[ 28.862592] MacIO PCI driver attached to Paddington chipset
[ 28.863931] Can't request resource 0 for MacIO device 0.00000000:power-mg
[ 28.867185] mediabay0: Registered Heathrow media-bay
[ 28.867418] mediabay0: powering down
[ 29.101680] mediabay0: switching to 3
[ 29.101837] mediabay0: powering up
[ 29.325678] mediabay0: enabling (kind:3)
[ 29.389674] mediabay0: waiting reset (kind:3)
[ 29.517671] mediabay0: waiting IDE reset (kind:3)
[ 30.669655] mediabay0: waiting IDE ready (kind:3)
[ 30.701654] mediabay0: up before IDE init
[ 30.702187] input: Macintosh mouse button emulation as /class/input/input0
[ 30.703214] pmubl: Backlight initialized (pmubl)
[ 30.703626] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 30.703892] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 30.704483] adb: starting probe task...
[ 31.721652] ide0: Found Apple Heathrow ATA controller, bus ID 0, irq 20
[ 31.721971] Probing IDE interface ide0...
[ 32.177837] hda: TOSHIBA MK6409MAV, ATA DISK drive
[ 32.831125] adb devices: [2]: 2 c3 [3]: 3 1 [7]: 7 1f
[ 32.856981] ADB keyboard at 2, handler 1
[ 32.866098] Detected ADB keyboard, type ANSI.
[ 32.875370] input: ADB keyboard as /class/input/input1
[ 32.884642] input: ADB Powerbook buttons as /class/input/input2
[ 32.893677] hda: Enabling MultiWord DMA 2
[ 32.903665] ide0 at 0xcd012000-0xcd012007,0xcd012160 on irq 20
[ 32.913237] Registered ide1 for media bay 0
[ 32.913258] ide1: Found Apple Heathrow ATA controller, bus ID 1
(mediabay), irq 31
[ 32.922617] Probing IDE interface ide1...
[ 32.931262] ADB mouse at 3, handler set to 4 (trackpad)
[ 32.994257] input: ADB mouse as /class/input/input3
[ 33.003443] adb: finished probe task...
[ 33.401806] hdc: MATSHITADVD-ROM SR-8171, ATAPI CD/DVD-ROM drive
[ 33.745621] hdc: Enabling MultiWord DMA 2
[ 33.755698] ide1 at 0xcd018000-0xcd018007,0xcd018160 on irq 31
[ 33.765412] PowerMac i2c bus pmu 2 registered
[ 33.774661] PowerMac i2c bus pmu 1 registered
[ 33.784043] TCP cubic registered
[ 33.793047] NET: Registered protocol family 1
[ 33.802270] Freeing unused kernel memory: 188k init
[ 34.664163] Capability LSM initialized
[ 38.447109] usbcore: registered new interface driver usbfs
[ 38.447589] usbcore: registered new interface driver hub
[ 38.447958] usbcore: registered new device driver usb
[ 38.454521] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
(OHCI) Driver
[ 38.454718] ohci_hcd 0000:00:0e.0: OHCI Host Controller
[ 38.455604] ohci_hcd 0000:00:0e.0: new USB bus registered, assigned
bus number 1
[ 38.456008] ohci_hcd 0000:00:0e.0: irq 28, io mem 0x80882000
[ 38.639470] usb usb1: configuration #1 chosen from 1 choice
[ 38.639953] hub 1-0:1.0: USB hub found
[ 38.640203] hub 1-0:1.0: 2 ports detected
[ 39.237886] SCSI subsystem initialized
[ 39.245662] mesh: configured for synchronous 5 MB/s
[ 39.449782] mesh: performing initial bus reset...
[ 39.844696] hda: max request size: 128KiB
[ 40.042244] hda: 12685680 sectors (6495 MB), CHS=13424/15/63, (U)DMA
[ 40.042711] hda: cache flushes not supported
[ 40.043104] hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8
[ 40.203217] hdc: ATAPI 20X DVD-ROM drive, 512kB Cache, DMA
[ 40.203702] Uniform CD-ROM driver Revision: 3.20
[ 41.374431] Attempting manual resume
[ 41.548016] kjournald starting. Commit interval 5 seconds
[ 41.548450] EXT3-fs: mounted filesystem with ordered data mode.
[ 43.453569] scsi0 : MESH
[ 44.003875] eth0: BMAC+ at 00:50:e4:7a:47:51
[ 49.460579] phy registers:
[ 49.460599] 0800 7849 2000 5c10 01e1 41e1 0007 2801
[ 49.470965] 0000 0000 0000 0000 0000 0000 0000 0000
[ 49.481324] 2002 0000 0000 0000 0001 0000 0020 0000
[ 49.491685] 0000 0000 0180 0100 0006 0f00 0000 0000
[ 54.134269] NET: Registered protocol family 17
[ 57.029251] PCI: Enabling device 0000:00:13.0 (0000 -> 0002)
[ 57.029720] Yenta: CardBus bridge found at 0000:00:13.0 [0000:0000]
[ 57.030038] PCI: Bus 1, cardbus bridge: 0000:00:13.0
[ 57.030265] IO window: 00001400-000015ff
[ 57.030459] IO window: 00001800-000019ff
[ 57.030653] PREFETCH window: 80000000-803fffff
[ 57.030867] MEM window: 80400000-807fffff
[ 57.031066] Yenta: Enabling burst memory read transactions
[ 57.031312] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 57.031567] Yenta: Routing CardBus interrupts to PCI
[ 57.031791] Yenta TI: socket 0000:00:13.0, mfunc 0x00000002, devctl 0x60
[ 57.133371] Yenta: ISA IRQ mask 0x0000, PCI irq 22
[ 57.133697] Socket status: 30000006
[ 57.133871] pcmcia: parent PCI bridge I/O window: 0x0 - 0x7fffff
[ 57.134140] pcmcia: parent PCI bridge Memory window: 0x80000000 - 0xfcffffff
[ 57.134443] pcmcia: parent PCI bridge Memory window: 0xfd000000 - 0xfdffffff
[ 62.931940] pmac_zilog: 0.6 (Benjamin Herrenschmidt
<benh at kernel.crashing.org>)
[ 62.939055] pmac_zilog: serial modem detected
[ 62.939539] ttyS0 at MMIO 0x80813020 (irq = 35) is a Z85c30 ESCC -
Internal modem
[ 62.948488] ttyS1 at MMIO 0x80813000 (irq = 38) is a Z85c30 ESCC -
Infrared port
[ 63.519859] apm_emu: APM Emulation 0.5 initialized.
[ 66.254320] input: PowerMac Beep as /class/input/input4
[ 67.170934] Adding 351552k swap on
/dev/disk/by-uuid/5de2f7e0-bb6e-49cc-b4c6-6e2fc4b74459. Priority:-1
extents:1 across:351552k
[ 67.564338] EXT3 FS on hda3, internal journal
[ 68.528530] kjournald starting. Commit interval 5 seconds
[ 68.529919] EXT3 FS on hda8, internal journal
[ 68.529942] EXT3-fs: mounted filesystem with ordered data mode.
[ 68.563591] kjournald starting. Commit interval 5 seconds
[ 68.564666] EXT3 FS on hda7, internal journal
[ 68.564689] EXT3-fs: mounted filesystem with ordered data mode.
[ 68.626515] kjournald starting. Commit interval 5 seconds
[ 68.627792] EXT3 FS on hda4, internal journal
[ 68.627813] EXT3-fs: mounted filesystem with ordered data mode.
[ 68.669914] kjournald starting. Commit interval 5 seconds
[ 68.694117] EXT3 FS on hda5, internal journal
[ 68.694140] EXT3-fs: mounted filesystem with ordered data mode.
[ 103.388928] lp: driver loaded but no devices found
[ 106.150040] ppdev: user-space parallel port driver
[ 196.111372] pccard: PCMCIA card inserted into slot 0
[ 196.111407] cs: memory probe 0x80000000-0xfcffffff: excluding
0x80000000-0x81ffffff
[ 196.230699] cs: memory probe 0xfd000000-0xfdffffff:Machine check in
kernel mode.
[ 196.230784] Caused by (from SRR1=49030): Transfer error ack signal
[ 196.231010] Oops: Machine check, sig: 7 [#1]
[ 196.231316]
[ 196.231408] Modules linked in: ppdev lp parport cpufreq_userspace
cpufreq_stats cpufreq_powersave cpufreq_ondemand cpufreq_conservative
snd_powermac snd_pcm_oss snd_pcm snd_mixer_oss snd_seq_dummy
snd_seq_oss snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq
snd_timer snd_seq_device snd soundcore snd_page_alloc apm_emu
pmac_zilog serial_core pcmcia yenta_socket rsrc_nonstatic pcmcia_core
af_packet tsdev evdev ext3 jbd mbcache ide_cd cdrom ide_disk bmac mesh
scsi_mod ohci_hcd usbcore capability commoncap
[ 196.234132] NIP: CD8ECD18 LR: CD8ECCEC CTR: C0014B88
[ 196.234360] REGS: cbe27c80 TRAP: 0200 Not tainted (2.6.20-15-powerpc)
[ 196.234646] MSR: 00049030 <EE,ME,IR,DR> CR: 82004024 XER: 00000000
[ 196.235026] TASK = c1f15870[3057] 'pccardd' THREAD: cbe26000
[ 196.235248] GPR00: 000000FF CBE27D30 C1F15870 CD990000 CD8A8014
00000070 00000002 CBE27D89
[ 196.235721] GPR08: CD8A8040 00001000 CD990000 CD991000 22000022
00000000 00000000 FD000000
[ 196.236194] GPR16: CD880000 FD100000 FE000000 FD000000 00200000
CB8A1428 FD080000 000004FB
[ 196.236668] GPR24: CBE27D89 00000000 00000002 CB8A1428 00000021
00000000 00000002 CBE27D89
[ 196.237172] NIP [CD8ECD18] pcmcia_read_cis_mem+0x178/0x26c [pcmcia_core]
[ 196.237540] LR [CD8ECCEC] pcmcia_read_cis_mem+0x14c/0x26c [pcmcia_core]
[ 196.237854] Call Trace:
[ 196.237984] [CBE27D30] [CD8ECCEC] pcmcia_read_cis_mem+0x14c/0x26c
[pcmcia_core] (unreliable)
[ 196.238390] [CBE27D60] [CD8ECF74] read_cis_cache+0x168/0x16c [pcmcia_core]
[ 196.238721] [CBE27D80] [CD8ED1CC] pccard_get_next_tuple+0x1b0/0x480
[pcmcia_core]
[ 196.239076] [CBE27DC0] [CD8ED534] pccard_get_first_tuple+0x98/0x144
[pcmcia_core]
[ 196.239431] [CBE27DF0] [CD8EDB84] pccard_validate_cis+0xa0/0x230
[pcmcia_core]
[ 196.239775] [CBE27E20] [CD881EBC] readable+0x54/0xd8 [rsrc_nonstatic]
[ 196.240094] [CBE27E40] [CD8821E8]
pcmcia_nonstatic_validate_mem+0x16c/0x408 [rsrc_nonstatic]
[ 196.240475] [CBE27EC0] [CD8EDD3C] pcmcia_validate_mem+0x28/0x40 [pcmcia_core]
[ 196.240817] [CBE27ED0] [CD9227FC] pcmcia_card_add+0x40/0xd0 [pcmcia]
[ 196.241157] [CBE27F40] [CD922934] ds_event+0xa8/0xd4 [pcmcia]
[ 196.241443] [CBE27F60] [CD8EA4F8] send_event+0x6c/0x94 [pcmcia_core]
[ 196.241757] [CBE27F70] [CD8EAA98] socket_insert+0xbc/0x130 [pcmcia_core]
[ 196.242081] [CBE27F80] [CD8EB164] pccardd+0x260/0x2b0 [pcmcia_core]
[ 196.242389] [CBE27FC0] [C0046968] kthread+0xc0/0xfc
[ 196.242647] [CBE27FF0] [C0014434] kernel_thread+0x44/0x60
[ 196.242912] Instruction dump:
[ 196.243071] 4bfffd91 2c030000 41820104 813b00ec 3809ffff 7d634a14
7c00e838 7d430214
[ 196.243520] 7f8b5000 419e006c 7c0004ac 7c0300ae <0c000000> 4c00012c
3bdeffff 981f0000
lspci
00:00.0 Host bridge: Motorola MPC106 [Grackle] (rev 40)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
00:0e.0 USB Controller: Agere Systems USB (rev 12) (prog-if 10 [OHCI])
Subsystem: Agere Systems USB
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 21500ns max)
Interrupt: pin A routed to IRQ 28
Region 0: Memory at 80882000 (32-bit, non-prefetchable) [size=4K]
00:0f.0 Multimedia controller: C-Cube Microsystems Cinemaster C 3.0
DVD Decoder (rev 02)
Subsystem: C-Cube Microsystems Cinemaster C 3.0 DVD Decoder
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 26
Region 0: I/O ports at 0c00 [size=256]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 Class ff00: Apple Computer Inc. Paddington Mac I/O
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Region 0: Memory at 80800000 (32-bit, non-prefetchable) [size=512K]
00:11.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro
(rev dc) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at 81000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at 80881000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 CardBus bridge: Texas Instruments PCI1211
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at 80880000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 80000000-803ff000 (prefetchable)
Memory window 1: 80400000-807ff000
I/O window 0: 00001400-000015ff
I/O window 1: 00001800-000019ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
/proc/ioports
00000000-007fffff : /pci at 80000000
00000c00-00000cff : 0000:00:0f.0
00001000-000010ff : 0000:00:11.0
00001400-000015ff : PCI CardBus #01
00001800-000019ff : PCI CardBus #01
/proc/iomem
80000000-fcffffff : /pci at 80000000
80000000-803fffff : PCI CardBus #01
80400000-807fffff : PCI CardBus #01
80800000-8087ffff : 0000:00:10.0
80800000-8087ffff : 0.80800000:mac-io
80800010-8080002f : 0.00000010:interrup
80800034-80800034 : 0.00000034:media-ba
80800034-80800034 : media-bay
80808000-808080ff : 0.00010000:scsi
80808000-808080ff : mesh
80808100-808081ff : 0.00015000:fdc
80808200-808082ff : 0.00011000:ethernet
80808200-808082ff : bmac
80808300-808083ff : 0.00011000:ethernet
80808300-808083ff : bmac
80808800-808088ff : 0.00014000:davbus
80808800-808088ff : Sound Tx DMA
80808900-808089ff : 0.00014000:davbus
80808900-808089ff : Sound Rx DMA
80808b00-80808bff : 0.00020000:ata-3
80808b00-80808bff : ide-pmac (dma)
80808c00-80808cff : 0.00021000:ata-3
80808c00-80808cff : ide-pmac (dma)
80810000-80810fff : 0.00010000:scsi
80810000-80810fff : mesh
80811000-80811fff : 0.00011000:ethernet
80811000-80811fff : bmac
80813000-80813000 : 0.00013000:ch-b
80813000-80813000 : pmac_zilog
80813010-80813010 : 0.00013000:ch-b
80813010-80813010 : pmac_zilog
80813020-80813020 : 0.00013020:ch-a
80813020-80813020 : pmac_zilog
80813030-80813030 : 0.00013020:ch-a
80813030-80813030 : pmac_zilog
80813040-80813040 : 0.00013000:ch-b
80813040-80813040 : pmac_zilog
80813050-80813050 : 0.00013020:ch-a
80813050-80813050 : pmac_zilog
80814000-80814fff : 0.00014000:davbus
80814000-80814fff : Sound Control
80815000-80815fff : 0.00015000:fdc
80816000-80817fff : 0.00016000:via-pmu
80820000-80820fff : 0.00020000:ata-3
80820000-80820fff : ide-pmac (ports)
80821000-80821fff : 0.00021000:ata-3
80821000-80821fff : ide-pmac (ports)
80880000-80880fff : 0000:00:13.0
80880000-80880fff : yenta_socket
80881000-80881fff : 0000:00:11.0
80881000-80881fff : atyfb
80882000-80882fff : 0000:00:0e.0
80882000-80882fff : ohci_hcd
81000000-81ffffff : 0000:00:11.0
81000000-81ffffff : atyfb
fd000000-fdffffff : /pci at 80000000
fd000000-fd07ffff : cs memory probe
fd080000-fd0fffff : cs memory probe
fffffffffd000000-fffffffffdfffffe : reserved
/proc/interrupts
CPU0
16: 19 PMAC-PIC Edge PMac Output
17: 1 PMAC-PIC Edge PMac
18: 107321 PMAC-PIC Edge VIA-PMU
19: 0 PMAC-PIC Edge PMac Input
20: 10297 PMAC-PIC Edge ide0
22: 2 PMAC-PIC Level yenta
23: 14 PMAC-PIC Edge MESH
28: 2 PMAC-PIC Level ohci_hcd:usb1
31: 16703 PMAC-PIC Edge ide1
32: 927 PMAC-PIC Edge BMAC-txdma
33: 1108 PMAC-PIC Edge BMAC-rxdma
42: 2100 PMAC-PIC Edge BMAC-misc
BAD: 0
/etc/pcmcia/config.opts
#
# Local PCMCIA Configuration File
#
#----------------------------------------------------------------------
#
# System resources available for PCMCIA cards
#
# NOTE: these settings have no effect on resources assigned to a
# CardBus bridge device itself; this file only affects resources
# assigned to cards. Also, interrupt settings here will only affect
# ISA bus interrupts assigned to 16-bit cards. PCI interrupts
# generally can't be reconfigured.
#
# With the kernel PCMCIA subsystem, these settings also have no effect
# at all on resources used for 32-bit CardBus cards. Those are set by
# the PCI hotplug subsystem.
#
include port 0x100-0x4ff
include port 0x1000-0x17ff
include memory 0x80000000-0x80ffffff
More information about the linux-pcmcia
mailing list