Trouble with CardBus wireless card. Please help me!
Sangre
Sangre at inbox.ru
Tue Jan 17 13:30:36 EST 2006
Hello!
I have old laptop IBM Thinkpad 600 (2645-45U) and two 32-Bit CardBus adapters:
1.TRENDnet TE100-PCUSR 10/100Mbps (work with driver 8139too);
2.D-Link AirPlus DWL-G650+ B1 Wireless CardBus Adapter (in 2.4.X kernel I use
acx100 driver - it works fine).
I use Gentoo Linux.
In 2.4 kernel, all hardware working fine, but system work slow.
I try use 2.6.14 and my wireless card not start. Wired card work normal.
Kernel version:
Linux book 2.6.14-gentoo-r4 #30 PREEMPT Tue Jan 17 00:26:20 MSK 2006 i686
Pentium II (Deschutes) GenuineIntel GNU/Linux
I try bootparam pci=assign-busses...
dmesg with "pci=assign-busses":
----------------------------------- BEGIN -----------------------------------
Linux version 2.6.14-gentoo-r4 (root at book) (gcc version 3.3.5 (Gentoo Linux
3.3.5-r1, ssp-3.3.2-3, pie-8.7.7.1)) #30 PREEMPT Tue Jan 17 00:26:20 MSK
2006 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000009fd0000 (usable)
BIOS-e820: 0000000009fd0000 - 0000000009fdf000 (ACPI data)
BIOS-e820: 0000000009fdf000 - 0000000009fe0000 (ACPI NVS)
BIOS-e820: 0000000009fe0000 - 000000000a000000 (reserved)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
159MB LOWMEM available.
On node 0 totalpages: 40912
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 36816 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI 2.0 present.
ACPI: RSDP (v000 IBM ) @ 0x000fd6e0
ACPI: RSDT (v001 IBM TP600 0x00000001 0x00000000) @ 0x09fd0000
ACPI: FADT (v001 IBM TP600 0x00000001 0x00000000) @ 0x09fd0100
ACPI: BOOT (v001 IBM TP600 0x00000001 0x00000000) @ 0x09fd0040
ACPI: DSDT (v001 IBM TP600 0x00000105 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0xef08
Allocating PCI resources starting at 10000000 (gap: 0a000000:f5fe0000)
Built 1 zonelists
Kernel command line: root=/dev/hda3 pci=assign-busses
splash=silent,theme:login-scan CONSOLE=/dev/tty1 resume=/dev/hda2
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 298.486 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 156780k/163648k available (2361k kernel code, 6264k reserved, 730k
data, 1064k init, 0k highmem) Checking if this processor honours the WP bit
even in supervisor mode... Ok. Calibrating delay using timer specific
routine.. 597.34 BogoMIPS (lpj=298670) Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000
00000000 00000000 00000000 CPU: After vendor identify, caps: 0183f9ff
00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K,
L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000
00000000 00000000 Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0800)
checking if image is initramfs... it is
Freeing initrd memory: 412k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd880, last bus=6
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0,
disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
*0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14
15) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11
12 14 15) *0, disabled. ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:03.0
PCI quirk: region ef00-ef3f claimed by PIIX4 ACPI
PCI quirk: region efa0-efbf claimed by PIIX4 SMB
PIIX4 devres I PIO at 002e-002f
PIIX4 devres J PIO at 15e8-15ef
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [PSIO] (on)
ACPI: Embedded Controller [EC0] (gpe 9)
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PVID] (on)
ACPI: Power Resource [PRSD] (off)
ACPI: Power Resource [PDCK] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 17 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report pnp: 00:0c: ioport range 0x15e0-0x15ef has been reserved
pnp: 00:0c: ioport range 0xef00-0xef3f could not be reserved
pnp: 00:0c: ioport range 0xefa0-0xefaf has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:03.0
PCI: Bus 1, cardbus bridge: 0000:00:02.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
PCI: Bus 5, cardbus bridge: 0000:00:02.1
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 14000000-15ffffff
MEM window: 16000000-17ffffff
ACPI: PCI Interrupt Link [LNKA] disabled and referenced, BIOS bug.
ACPI: PCI Interrupt Link [LNKA] BIOS reported IRQ 0, using IRQ 9
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 9 (level, low) ->
IRQ 9 ACPI: PCI Interrupt Link [LNKB] disabled and referenced, BIOS bug.
ACPI: PCI Interrupt Link [LNKB] BIOS reported IRQ 0, using IRQ 9
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNKB] -> GSI 9 (level, low) ->
IRQ 9 Simple Boot Flag at 0x33 set to 0x1
Limiting direct PCI/PCI transfers.
Real Time Clock Driver v1.12
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKA] -> GSI 9 (level, low) ->
IRQ 9 neofb: mapped io at ca880000
Autodetected internal display
Panel is a 1024x768 color TFT display
neofb: mapped framebuffer at cab00000
neofb v0.4.2: 2048kB VRAM, using 1024x768, 48.364kHz, 60Hz
Console: switching to colour frame buffer device 128x48
fbsplash: console 0 using theme 'login-scan'
fbsplash: switched splash state to 'on' on console 0
fb0: MagicGraph 128XD frame buffer device
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FN00] (off)
ACPI: Fan [FN20] (off)
ACPI: Fan [FN60] (off)
ACPI: Video Device [VID0] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THM0] (57 C)
ACPI: Thermal Zone [THM2] (40 C)
ACPI: Thermal Zone [THM6] (27 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:MOU0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
pnp: Device 00:02 activated.
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler cfq registered
RAMDISK driver initialized: 1 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard on isa0060/serio0
hda: HITACHI_DK23AA-60B, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
IBM TrackPoint firmware: 0x0b, buttons: 3/3
input: TPPS/2 IBM TrackPoint on isa0060/serio1
hdc: CRN-8241B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 11733120 sectors (6007 MB) w/512KiB Cache, CHS=12416/15/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 9 (level, low) ->
IRQ 9 Yenta: CardBus bridge found at 0000:00:02.0 [1014:0092]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0xfba97543, devctl 0x62
Yenta TI: socket 0000:00:02.0 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:02.0 no PCI interrupts. Fish. Please report.
Yenta: no PCI IRQ, CardBus support disabled for this socket.
Yenta: check your BIOS CardBus, BIOS IRQ or ACPI settings.
Yenta: ISA IRQ mask 0x04b8, PCI irq 0
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNKB] -> GSI 9 (level, low) ->
IRQ 9 Yenta: CardBus bridge found at 0000:00:02.1 [1014:0092]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0xfba97543, devctl 0x62
Yenta TI: socket 0000:00:02.1 probing PCI interrupt failed, trying to fix
Yenta TI: socket 0000:00:02.1 no PCI interrupts. Fish. Please report.
Yenta: no PCI IRQ, CardBus support disabled for this socket.
Yenta: check your BIOS CardBus, BIOS IRQ or ACPI settings.
Yenta: ISA IRQ mask 0x04b8, PCI irq 0
Socket status: 30000006
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKD] disabled and referenced, BIOS bug.
ACPI: PCI Interrupt Link [LNKD] BIOS reported IRQ 0, using IRQ 10
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low)
-> IRQ 10 uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
irq 10: nobody cared (try booting with the "irqpoll" option)
[<c0138ada>] __report_bad_irq+0x2a/0xa0
[<c01383b0>] handle_IRQ_event+0x30/0x70
[<c0138bf0>] note_interrupt+0x80/0xf0
[<c01384c0>] __do_IRQ+0xd0/0xe0
[<c0104b19>] do_IRQ+0x19/0x30
[<c0103342>] common_interrupt+0x1a/0x20
[<c011d69e>] __do_softirq+0x2e/0x90
[<c011d726>] do_softirq+0x26/0x30
[<c011d7f5>] irq_exit+0x35/0x40
[<c0104b1e>] do_IRQ+0x1e/0x30
[<c0103342>] common_interrupt+0x1a/0x20
[<c01d007b>] nlm4svc_callback_exit+0xb/0x60
[<c0138742>] setup_irq+0xb2/0x130
[<c029def0>] usb_hcd_irq+0x0/0x60
[<c0138952>] request_irq+0x82/0xa0
[<c029e387>] usb_add_hcd+0x2a7/0x390
[<c029def0>] usb_hcd_irq+0x0/0x60
[<c01df956>] pci_set_master+0x46/0x80
[<c02a5b1b>] usb_hcd_pci_probe+0x21b/0x360
[<c01e15d9>] pci_call_probe+0x19/0x20
[<c01e1645>] __pci_device_probe+0x65/0x80
[<c01e168f>] pci_device_probe+0x2f/0x50
[<c0255bf8>] driver_probe_device+0x38/0xb0
[<c0255cf0>] __driver_attach+0x0/0x50
[<c0255d37>] __driver_attach+0x47/0x50
[<c0255149>] bus_for_each_dev+0x69/0x80
[<c0255d65>] driver_attach+0x25/0x30
[<c0255cf0>] __driver_attach+0x0/0x50
[<c025569d>] bus_add_driver+0x8d/0xe0
[<c02561d0>] driver_register+0x40/0x50
[<c0256170>] klist_devices_get+0x0/0x10
[<c0256180>] klist_devices_put+0x0/0x10
[<c01e1950>] pci_register_driver+0x70/0x90
[<c042038b>] uhci_hcd_init+0x9b/0xf0
[<c04088bb>] do_initcalls+0x2b/0xc0
[<c04222fa>] sock_init+0x2a/0x40
[<c01002a0>] init+0x0/0x160
[<c01002ca>] init+0x2a/0x160
[<c0101394>] kernel_thread_helper+0x0/0xc
[<c0101399>] kernel_thread_helper+0x5/0xc
handlers:
[<c029def0>] (usb_hcd_irq+0x0/0x60)
Disabling IRQ #10
uhci_hcd 0000:00:07.2: irq 10, io base 0x00008400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12
08:13:09 2005 UTC). ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
LID0 SLPB PCI0 UAR1 MWV0 BAT0 USB0
ACPI: (supports S0 S1 S3 S4 S5)
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 1064k freed
kjournald starting. Commit interval 5 seconds
Adding 136072k swap on /dev/hda2. Priority:-1 extents:1 across:136072k
EXT3-fs warning: mounting fs with errors, running e2fsck is recommended
EXT3 FS on hda3, internal journal
subfs 0.9
------------------------------------ END ------------------------------------
In this case yenta_socket dont start.
My laptop very old end I try with bootparam "pci=assign-busses,noacpi"
dmesg with "pci=assign-busses,noacpi":
----------------------------------- BEGIN -----------------------------------
Linux version 2.6.14-gentoo-r4 (root at book) (gcc version 3.3.5 (Gentoo Linux
3.3.5-r1, ssp-3.3.2-3, pie-8.7.7.1)) #30 PREEMPT Tue Jan 17 00:26:20 MSK 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000009fd0000 (usable)
BIOS-e820: 0000000009fd0000 - 0000000009fdf000 (ACPI data)
BIOS-e820: 0000000009fdf000 - 0000000009fe0000 (ACPI NVS)
BIOS-e820: 0000000009fe0000 - 000000000a000000 (reserved)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
159MB LOWMEM available.
On node 0 totalpages: 40912
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 36816 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI 2.0 present.
ACPI: RSDP (v000 IBM ) @ 0x000fd6e0
ACPI: RSDT (v001 IBM TP600 0x00000001 0x00000000) @ 0x09fd0000
ACPI: FADT (v001 IBM TP600 0x00000001 0x00000000) @ 0x09fd0100
ACPI: BOOT (v001 IBM TP600 0x00000001 0x00000000) @ 0x09fd0040
ACPI: DSDT (v001 IBM TP600 0x00000105 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0xef08
Allocating PCI resources starting at 10000000 (gap: 0a000000:f5fe0000)
Built 1 zonelists
Kernel command line: root=/dev/hda3 pci=assign-busses,noacpi
splash=silent,theme:login-scan CONSOLE=/dev/tty1 resume=/dev/hda2
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 298.504 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 156780k/163648k available (2361k kernel code, 6264k reserved, 730k
data, 1064k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 597.35 BogoMIPS (lpj=298675)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000
00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Pentium II (Deschutes) stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0a00 (from 0800)
checking if image is initramfs... it is
Freeing initrd memory: 412k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd880, last bus=6
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:03.0
PCI quirk: region ef00-ef3f claimed by PIIX4 ACPI
PCI quirk: region efa0-efbf claimed by PIIX4 SMB
PIIX4 devres I PIO at 002e-002f
PIIX4 devres J PIO at 15e8-15ef
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [PSIO] (on)
ACPI: Embedded Controller [EC0] (gpe 9)
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PVID] (on)
ACPI: Power Resource [PRSD] (off)
ACPI: Power Resource [PDCK] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 17 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
PCI: IRQ 0 for device 0000:00:02.0 doesn't match PIRQ mask - try
pci=usepirqmask
PCI: Found IRQ 11 for device 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:03.0
PCI: IRQ 0 for device 0000:00:02.1 doesn't match PIRQ mask - try
pci=usepirqmask
PCI: Found IRQ 11 for device 0000:00:02.1
pnp: 00:0c: ioport range 0x15e0-0x15ef has been reserved
pnp: 00:0c: ioport range 0xef00-0xef3f could not be reserved
pnp: 00:0c: ioport range 0xefa0-0xefaf has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:03.0
PCI: Bus 1, cardbus bridge: 0000:00:02.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
PCI: Bus 5, cardbus bridge: 0000:00:02.1
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 14000000-15ffffff
MEM window: 16000000-17ffffff
PCI: Found IRQ 11 for device 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:03.0
PCI: Found IRQ 11 for device 0000:00:02.1
Simple Boot Flag at 0x33 set to 0x1
Limiting direct PCI/PCI transfers.
Real Time Clock Driver v1.12
PCI: Found IRQ 11 for device 0000:00:03.0
PCI: Sharing IRQ 11 with 0000:00:02.0
neofb: mapped io at ca880000
Autodetected internal display
Panel is a 1024x768 color TFT display
neofb: mapped framebuffer at cab00000
neofb v0.4.2: 2048kB VRAM, using 1024x768, 48.364kHz, 60Hz
Console: switching to colour frame buffer device 128x48
fbsplash: console 0 using theme 'login-scan'
fbsplash: switched splash state to 'on' on console 0
fb0: MagicGraph 128XD frame buffer device
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FN00] (off)
ACPI: Fan [FN20] (off)
ACPI: Fan [FN60] (off)
ACPI: Video Device [VID0] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THM0] (62 C)
ACPI: Thermal Zone [THM2] (43 C)
ACPI: Thermal Zone [THM6] (27 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:MOU0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
pnp: Device 00:02 activated.
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler cfq registered
RAMDISK driver initialized: 1 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard on isa0060/serio0
hda: HITACHI_DK23AA-60B, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
IBM TrackPoint firmware: 0x0b, buttons: 3/3
input: TPPS/2 IBM TrackPoint on isa0060/serio1
hdc: CRN-8241B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 11733120 sectors (6007 MB) w/512KiB Cache, CHS=12416/15/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
PCI: Found IRQ 11 for device 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:03.0
Yenta: CardBus bridge found at 0000:00:02.0 [1014:0092]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0xfba97543, devctl 0x62
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000006
PCI: Found IRQ 11 for device 0000:00:02.1
Yenta: CardBus bridge found at 0000:00:02.1 [1014:0092]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0xfba97543, devctl 0x62
Yenta: ISA IRQ mask 0x04b8, PCI irq 11
Socket status: 30000006
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 11 for device 0000:00:07.2
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00008400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12
08:13:09 2005 UTC).
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
LID0 SLPB PCI0 UAR1 MWV0 BAT0 USB0
ACPI: (supports S0 S1 S3 S4 S5)
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 1064k freed
kjournald starting. Commit interval 5 seconds
Adding 136072k swap on /dev/hda2. Priority:-1 extents:1 across:136072k
EXT3-fs warning: mounting fs with errors, running e2fsck is recommended
EXT3 FS on hda3, internal journal
subfs 0.9
------------------------------------ END ------------------------------------
Ok. No errors.
I try insert my wired card - dmesg:
----------------------------------- BEGIN ----------------------------------
8139too Fast Ethernet driver 0.9.27
PCI: Enabling device 0000:05:00.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:05:00.0 to 64
eth0: RealTek RTL8139 at 0xca84c000, 00:e0:98:b4:a1:ed, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
------------------------------------ END ------------------------------------
network work fine...
When I try insert wireless card dmesg do nothing...
I look lspci -vvv:
----------------------------------- BEGIN ----------------------------------
00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
(AGP disabled) (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
Latency: 64
Region 0: Memory at <unassigned> (32-bit, prefetchable)
00:02.0 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Subsystem: IBM ThinkPad 600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20301000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10000000-11fff000 (prefetchable)
Memory window 1: 12000000-13fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:02.1 CardBus bridge: Texas Instruments PCI1250 (rev 02)
Subsystem: IBM ThinkPad 600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 08
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 20300000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 14000000-15fff000 (prefetchable)
Memory window 1: 16000000-17fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:03.0 VGA compatible controller: Neomagic Corporation NM2160 [MagicGraph
128XD] (rev 01) (prog-if 00 [VGA])
Subsystem: Neomagic Corporation MagicGraph 128XD
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 128 (4000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at 20000000 (32-bit, non-prefetchable) [size=2M]
Region 2: Memory at 20200000 (32-bit, non-prefetchable) [size=1M]
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 48
Region 4: I/O ports at fcf0 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 48
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 8400 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 01)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
01:00.0 Ethernet controller: Abocom Systems Inc RTL8139 [FE2000VX] CardBus
Fast Ethernet Attached Port Adapter (rev 10)
Subsystem: Abocom Systems Inc RTL8139 [FE2000VX] CardBus Fast Ethernet
Attached Port Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1000 [size=256]
Region 1: Memory at 12000000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:00.0 Network controller: Texas Instruments ACX 111 54Mbps Wireless
Interface
Subsystem: D-Link System Inc DWL-G650+ AirPlusG+ CardBus Wireless LAN
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 16020000 (32-bit, non-prefetchable) [disabled] [size=8K]
Region 1: Memory at 16000000 (32-bit, non-prefetchable) [disabled]
[size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
------------------------------------ END ------------------------------------
Kernel config:
----------------------------------- BEGIN ----------------------------------
#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=y
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=m
CONFIG_PCMCIA_LOAD_CIS=y
CONFIG_PCMCIA_IOCTL=y
CONFIG_CARDBUS=y
#
# PC-card bridges
#
CONFIG_YENTA=y
# CONFIG_PD6729 is not set
# CONFIG_I82092 is not set
# CONFIG_I82365 is not set
# CONFIG_TCIC is not set
CONFIG_PCMCIA_PROBE=y
CONFIG_PCCARD_NONSTATIC=y
------------------------------------ END ------------------------------------
Strange output pccardctrl:
1. pccardctl info:
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255
PRODID_1=""
PRODID_2=""
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
FUNCID=255
2. pccardctl ident:
Socket 0:
no product info available
Socket 1:
no product info available
3. pccardctl status:
Socket 0:
3.3V 32-bit PC Card
Socket 1:
3.3V 32-bit PC Card
If You may please help.
I am very sorry... I know my English very bad.
________
Serge E. Malochinskiy
mail-to: Sangre at inbox.ru
More information about the linux-pcmcia
mailing list