PCMCIA Dead with 2.6.14-2-386

Roger Smith rogersmi at bigpond.net.au
Tue Jan 3 08:40:28 EST 2006


Previous kernel PCMCIA worked great.  This kernel it is dead.
Using PCMCIA.utils and udev.
Debian Etch on a Thinkpad a21m.

LSPCI -VV reads.
0000:00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX 
Host bridge (rev 03)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 64
        Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [a0] AGP version 1.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- 
HTrans- 64bit- FW- AGP3- Rate=x1,x2
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- 
Rate=<none>

0000:00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX 
AGP bridge (rev 03) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 128
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        I/O behind bridge: 00003000-00003fff
        Memory behind bridge: f4200000-f5ffffff
        Prefetchable memory behind bridge: 28000000-280fffff
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+

0000:00:02.0 CardBus bridge: Texas Instruments PCI1450 (rev 03)
        Subsystem: IBM Thinkpad T20
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 168, Cache Line Size: 0x20 (128 bytes)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
        Memory window 0: 20000000-21fff000 (prefetchable)
        Memory window 1: 22000000-23fff000
        I/O window 0: 00001400-000014ff
        I/O window 1: 00002400-000024ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- 
PostWrite+
        16-bit legacy interface ports at 0001

0000:00:02.1 CardBus bridge: Texas Instruments PCI1450 (rev 03)
        Subsystem: IBM Thinkpad T20
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 168, Cache Line Size: 0x20 (128 bytes)
        Interrupt: pin B routed to IRQ 11
        Region 0: Memory at 50100000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
        Memory window 0: 24000000-25fff000 (prefetchable)
        Memory window 1: 26000000-27fff000
        I/O window 0: 00002800-000028ff
        I/O window 1: 00002c00-00002cff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ 
PostWrite+
        16-bit legacy interface ports at 0001

0000:00:03.0 Ethernet controller: 3Com Corporation 3c556B CardBus 
[Tornado] (rev 20)
        Subsystem: 3Com Corporation: Unknown device 6356
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 
bytes)
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at 1800 [size=256]
        Region 1: Memory at f4101400 (32-bit, non-prefetchable) [size=128]
        Region 2: Memory at f4101000 (32-bit, non-prefetchable) [size=128]
        Expansion ROM at 28100000 [disabled] [size=128K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:00:03.1 Communication controller: 3Com Corporation Mini PCI 56k 
Winmodem (rev 20)
        Subsystem: 3Com Corporation: Unknown device 6159
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 11
        Region 0: I/O ports at 2000 [size=256]
        Region 1: Memory at f4101c00 (32-bit, non-prefetchable) [size=256]
        Region 2: Memory at f4101800 (32-bit, non-prefetchable) [size=128]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA 
PME(D0+,D1-,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:00:05.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24 
[CrystalClear SoundFusion Audio Accelerator] (rev 01)
        Subsystem: IBM: Unknown device 0153
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (1000ns min, 6000ns max)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at f4100000 (32-bit, non-prefetchable) [size=4K]
        Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=1M]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

0000:00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE 
(rev 01) (prog-if 80 [Master])
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Region 4: I/O ports at 1c00 [size=16]

0000:00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB 
(rev 01) (prog-if 00 [UHCI])
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin D routed to IRQ 11
        Region 4: I/O ports at 1c20 [size=32]

0000:00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin ? routed to IRQ 9

0000:01:00.0 VGA compatible controller: ATI Technologies Inc Rage 
Mobility P/M AGP 2x (rev 64) (prog-if 00 [VGA])
        Subsystem: IBM ThinkPad A20m
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: I/O ports at 3000 [size=256]
        Region 2: Memory at f4200000 (32-bit, non-prefetchable) [size=4K]
        Expansion ROM at 28000000 [disabled] [size=128K]
        Capabilities: [50] AGP version 1.0
                Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- 
HTrans- 64bit- FW- AGP3- Rate=x1,x2
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- 
Rate=<none>
        Capabilities: [5c] Power Management version 1
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:00.0 Network controller: Texas Instruments ACX 111 54Mbps 
Wireless Interface
        Subsystem: D-Link System Inc DWL-G650+ AirPlusG+ CardBus 
Wireless LAN
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at 22020000 (32-bit, non-prefetchable) 
[disabled] [size=8K]
        Region 1: Memory at 22000000 (32-bit, non-prefetchable) 
[disabled] [size=128K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-


No lights on NIC, no beep on insert or eject.


Any help gratefully accepted,

Thanks




More information about the linux-pcmcia mailing list