Modem PC Card on Compaq nx6110: No serial port created
Pascal MALAISE
malaise at magic.fr
Sat Apr 1 02:14:23 EST 2006
Hi,
I am trying to use a modem pc card (Zoltrix 56K modem) on a Compaq
nx6110. I run ubuntu breezy with a kernel 1.6.16.1 and pcmciautils-013.
When I insert the card, dmesg shows:
kernel: pccard: PCMCIA card inserted into slot 0
kernel: cs: memory probe 0xd0000000-0xd03fffff: excluding
0xd0000000-0xd003ffff
kernel: pcmcia: registering new device pcmcia0.0
And serial_cs module is inserted. However, there is no ttyS0 registered.
I tried with and without "pci=assign-busses" option to kernel. Same result.
Did I miss something? Any help would be appreciated.
You will find hereafter the traditionnal dumps...
Regards
--------------------------------------------------------------------------------------------
lspcmcia -vvv
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:02:06.0)
Configuration: state: on ready: yes
Voltage: 5.0V Vcc: 5.0V Vpp: 0.0V
Available IRQs: 3, 4, 5, 6, 7, 10, 11
Available iomem: 0x00000100 - 0x000003af
0x000003e0 - 0x000004cf
0x000004d8 - 0x000004ff
0x00000820 - 0x000008ff
0x00000a00 - 0x00000aff
0x00000c00 - 0x00000cf7
0x00003000 - 0x00003fff
Available ioports: 0x000c0000 - 0x000fffff
0xd0040000 - 0xd03fffff
Socket 0 Device 0: [serial_cs] (bus ID: 0.0)
Configuration: state: on
Product Name: PCMCIA CARD MEMBER FM56R-NCTV2 021
Identification: manf_id: 0x0013 card_id: 0x0000
function: 2 (serial)
prod_id(1): "PCMCIA CARD MEMBER" (0xc0473f9e)
prod_id(2): "FM56R-NCTV2" (0x5c245268)
prod_id(3): "021" (0x98c5b1db)
prod_id(4): --- (---)
--------------------------------------------------------------------------------------------
lspci -vvv
0000:00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML
Express Processor to DRAM Controller (rev 03)
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] #09 [3109]
0000:00:02.0 VGA compatible controller: Intel Corporation Mobile
915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0400000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 7000 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at d0480000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 Display controller: Intel Corporation Mobile
915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem:
Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at d0500000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 4: I/O ports at 2000 [size=32]
0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 2020 [size=32]
0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 16
Region 4: I/O ports at 2040 [size=32]
0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 4: I/O ports at 2060 [size=32]
0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0580000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev
d3) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d0000000-d03fffff
Prefetchable memory behind bridge: 0000000030000000-0000000031f00000
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] #0d [0000]
0000:00:1e.2 Multimedia audio controller: Intel Corporation
82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 2100 [size=256]
Region 1: I/O ports at 2200 [size=64]
Region 2: Memory at d0581000 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at d0582000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) AC'97 Modem Controller (rev 03) (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 22
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2500 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC
Interface Bridge (rev 03)
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW
(ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 2580 [size=16]
0000:02:04.0 Network controller: Broadcom Corporation BCM4318 [AirForce
One 54g] 802.11g Wireless LAN Controller (rev 02)
Subsystem: Hewlett-Packard Company nx6125
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=8K]
0000:02:06.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus
Controller
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x20 (128 bytes)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0002000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 30000000-31fff000 (prefetchable)
Memory window 1: 32000000-33fff000
I/O window 0: 00003000-000030ff
I/O window 1: 00003400-000034ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
0000:02:06.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE
1394 Host Controller (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 0x10 (64
bytes)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at d0003000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at d0004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:02:0e.0 Ethernet controller: Broadcom Corporation BCM4401-B0
100Base-TX (rev 02)
Subsystem: Hewlett-Packard Company nx6110/nc6120
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d000e000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
--------------------------------------------------------------------------------------------
dmesg
acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 2f800000:b0800000)
Built 1 zonelists
Kernel command line: ro reboot=b
mapped APIC to ffffd000 (fec01000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1399.959 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 767452k/778048k available (1857k kernel code, 10040k reserved,
728k data, 240k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2806.79 BogoMIPS
(lpj=5613584)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000
00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000000
00000000 00000000
CPU: Intel(R) Celeron(R) M processor 1.40GHz stepping 08
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0322, last bus=3
PCI: Using MMCONFIG
ACPI: Subsystem revision 20060127
ACPI Error (evgpeblk-0284): Unknown GPE method type: C20E (name not of
form _Lxx or _Exx) [20060127]
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [C002] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C002] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) may be hidden behind transparent bridge #02 (-#03)
(try 'pci=assign-busses')
ACPI: PCI Interrupt Routing Table [\_SB_.C002._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C002.C068._PRT]
ACPI: Embedded Controller [C004] (gpe 16) interrupt mode.
ACPI: Power Resource [C1C5] (on)
ACPI: PCI Interrupt Link [C0D8] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0D9] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0DA] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0DB] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0EE] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0EF] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0F0] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0F1] (IRQs 10 11) *0, disabled.
ACPI: Power Resource [C244] (off)
ACPI: Power Resource [C245] (off)
ACPI: Power Resource [C246] (off)
ACPI: Power Resource [C247] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 30000000-31ffffff
MEM window: 32000000-33ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: d0000000-d03fffff
PREFETCH window: 30000000-31ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 16
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
loop: loaded (max 8 devices)
b44.c:v0.97 (Nov 30, 2005)
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 16 (level, low) -> IRQ 17
eth0: Broadcom 4400 10/100BaseT Ethernet 00:14:c2:e5:f4:27
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 17
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2580-0x2587, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: HTS424040M9AT00, ATA DISK drive
hdb: HL-DT-STCD-RW/DVD DRIVE GCC-4244N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/1739KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 >
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 18, io mem 0xd0580000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 18, io base 0x00002000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002020
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 16, io base 0x00002040
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 20, io base 0x00002060
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on
usb-0000:00:1d.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
input: PC Speaker as /class/input/input2
i2c /dev entries driver
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
Cannot allocate resource for EISA slot 7
EISA: Detected 0 cards.
Advanced Linux Sound Architecture Driver Version 1.0.11rc2 (Wed Jan 04
08:57:20 2006 UTC).
ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1e.2 to 64
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input3
intel8x0_measure_ac97_clock: measured 55472 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: Intel ICH6 with AD1981B at 0xd0581000, irq 21
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
ip_conntrack version 2.4 (6078 buckets, 48624 max) - 172 bytes per conntrack
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno at linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
Using IPI Shortcut mode
ACPI wakeup devices:
C068 C0BB C0C2 C0C3 C0C4 C0C5
ACPI: (supports S0 S3 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 240k freed
Adding 827308k swap on /dev/hda5. Priority:-1 extents:1 across:827308k
EXT3 FS on hda2, internal journal
ieee1394: Initialized config rom entry `ip1394'
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
p4-clockmod: Warning: Pentium M detected. The speedstep_centrino module
offers voltage scaling in addition of frequency scaling. You should use
that instead of p4-clockmod, if possible.
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 22 (level, low) -> IRQ 22
ACPI: PCI interrupt for device 0000:00:1e.3 disabled
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:02:06.0 [103c:099c]
Yenta: Enabling burst memory read transactions
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:06.0, mfunc 0x01aa1b22, devctl 0x64
Yenta: ISA IRQ mask 0x0cf8, PCI irq 16
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0000000 - 0xd03fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
ACPI: PCI Interrupt 0000:02:06.2[C] -> GSI 22 (level, low) -> IRQ 22
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22]
MMIO=[d0003000-d00037ff] Max Packet=[2048] IR/IT contexts=[4/8]
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[718b500029e90aa6]
ACPI: AC Adapter [C172] (on-line)
ACPI: Battery Slot [C174] (battery present)
ACPI: Battery Slot [C173] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [C1E8]
ACPI: Lid Switch [C1E9]
ACPI: Fan [C248] (off)
ACPI: Fan [C249] (off)
ACPI: Fan [C24A] (off)
ACPI: Fan [C24B] (off)
Using specific hotkey driver
ibm_acpi: ec object not found
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (46 C)
ACPI: Thermal Zone [TZ2] (38 C)
ACPI: Thermal Zone [TZ3] (22 C)
ACPI: Thermal Zone [TZ4] (20 C)
toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
ACPI: Video Device [C055] (multi-head: yes rom: no post: no)
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
usb 2-2: new full speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
hub 2-2:1.0: USB hub found
hub 2-2:1.0: 4 ports detected
usb 2-2.4: new full speed USB device using uhci_hcd and address 4
usb 2-2.4: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: USB NAND Model: FLASH DISK Rev: 0.20
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 0b 00 00 08
sda: assuming drive cache: write through
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 0b 00 00 08
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
ndiswrapper version 1.11 loaded (preempt=no,smp=no)
ndiswrapper: driver bcmwl5 () loaded
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 21
ndiswrapper: using irq 21
wlan0: vendor: ''
wlan0: ndiswrapper ethernet device 00:14:a5:65:5f:d2 using driver
bcmwl5, 14E4:4318:103C:1356.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK;
AES/CCMP with WPA, WPA2, WPA2PSK
usb 2-2.4: USB disconnect, address 4
usb 2-2: USB disconnect, address 3
+ kernel logs when card is inserted, removed and inserted again.
pccard: PCMCIA card inserted into slot 0
cs: memory probe 0xd0000000-0xd03fffff: excluding 0xd0000000-0xd003ffff
pcmcia: registering new device pcmcia0.0
pccard: card ejected from slot 0
pccard: PCMCIA card inserted into slot 0
pcmcia: registering new device pcmcia0.0
More information about the linux-pcmcia
mailing list