Xircom pcmcia CEM56 eth/modem combo works on thinkpad 390 but not 600

Joseph Mack NA3T jmack at wm7d.net
Thu Oct 13 12:03:09 EDT 2005 

On Wed, 12 Oct 2005, Daniel Ritz wrote:

> On Wednesday 12 October 2005 14.25, Joseph Mack NA3T wrote:
>> On Tue, 11 Oct 2005, Both Daniel Ritz and David Hinds wrote
>>
>>>> Is the winmodem likely to be causing problems in linux-2.6.13? If so, what do I do?
>>
>>> How about:
>>>  exclude port 0x2f8-0x2ff
>>> in /etc/pcmcia/config.opts?

> you're using pcmciautils...so you have to run pcmcia-socket-startup

I shoulda just rebooted :-)

> to write the new values. also after boot, to make sure it's setup, do a:
> 	cat /sys/class/pcmcia_socket/pcmcia_socket0/available_resources_setup_done
> and:
> 	cat /sys/class/pcmcia_socket/pcmcia_socket0/available_resources_io
> to see the configured ranges

I run /sbin/pcmcia-socket-startup - available_resources_io 
shows that I _haven't_ excluded the ports I excluded in 
/etc/pcmcia/config.opts. (The card doesn't work either).

my syntax is

exclude port 0x2e8-0x2ef

I didn't really know what I was doing when I went from 2.4 
to 2.6, so I don't know that I have everything installed 
corectly.

>>
>>> - full dmesg

now attached for both machines

dmesg.foghorn.card_works
dmesg.igloo.card_doesnt_work

Thanks Joe
--
Joseph Mack NA3T EME(B,D), FM05lw North Carolina
jmack (at) wm7d (dot) net - azimuthal equidistant map
generator at http://www.wm7d.net/azproj.shtml 
Homepage http://www.austintek.com/ It's GNU/Linux!
-------------- next part --------------
Linux version 2.6.13 (root at foghorn) (gcc version 3.4.4) #1 Mon Aug 29 18:41:46 GMT 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e8c00 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
 BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
 BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
 BIOS-e820: 00000000fffe8c00 - 0000000100000000 (reserved)
user-defined physical RAM map:
 user: 0000000000000000 - 000000000009fc00 (usable)
 user: 000000000009fc00 - 00000000000a0000 (reserved)
 user: 00000000000e8c00 - 0000000000100000 (reserved)
 user: 0000000000100000 - 0000000007ff0000 (usable)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32752
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 28656 pages, LIFO batch:15
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.1 present.
Allocating PCI resources starting at 08000000 (gap: 07ff0000:f8010000)
Built 1 zonelists
Kernel command line: ro root=/dev/hda3 mem=131008K
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 331.765 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 126556k/131008k available (1612k kernel code, 3936k reserved, 682k data, 208k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 664.57 BogoMIPS (lpj=1329143)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Mobile Pentium II stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9c5, last bus=4
PCI: Using configuration type 1
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7250
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x8ba5, dseg 0x400
PnPBIOS: Unknown tag '0x82', length '25'.
PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:02.0
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: fe400000-febfffff
  PREFETCH window: f6000000-f6ffffff
PCI: Bus 2, cardbus bridge: 0000:00:03.0
  IO window: 00001400-000014ff
  IO window: 00001800-000018ff
  PREFETCH window: 08000000-09ffffff
  MEM window: 0a000000-0bffffff
PCI: Bus 6, cardbus bridge: 0000:00:03.1
  IO window: 00001c00-00001cff
  IO window: 00002000-000020ff
  PREFETCH window: 0c000000-0dffffff
  MEM window: 0e000000-0fffffff
PCI: Found IRQ 11 for device 0000:00:03.0
PCI: Sharing IRQ 11 with 0000:00:03.1
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Found IRQ 11 for device 0000:00:03.1
PCI: Sharing IRQ 11 with 0000:00:03.0
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Setting latency timer of device 0000:00:03.1 to 64
TC classifier action (bugs to netdev at vger.kernel.org cc hadi at cyberus.ca)
pnp: 00:00: ioport range 0x760-0x760 has been reserved
pnp: 00:00: ioport range 0x1050-0x105f has been reserved
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0b: ioport range 0x1000-0x103f has been reserved
pnp: 00:0b: ioport range 0x1040-0x104f has been reserved
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:02.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfc90-0xfc97, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xfc98-0xfc9f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK6025GAS, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CRN-8241B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(33)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 208k freed
input: PS/2 Generic Mouse on isa0060/serio1
Adding 72284k swap on /dev/hda2.  Priority:-1 extents:1
EXT3 FS on hda3, internal journal
Linux agpgart interface v0.101 (c) Dave Jones
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Intel ISA PCIC probe: not found.
Device 'i82365.0' does not have a release() function, it is broken and must be fixed.
Badness in device_release at drivers/base/core.c:83
 [<c01ba599>] kobject_cleanup+0xa9/0xb0
 [<c01ba5a0>] kobject_release+0x0/0x10
 [<c01bafb5>] kref_put+0x45/0x90
 [<c01ba5cf>] kobject_put+0x1f/0x30
 [<c01ba5cf>] kobject_put+0x1f/0x30
 [<c01ba5a0>] kobject_release+0x0/0x10
 [<c88013c9>] init_i82365+0x1c9/0x1df [i82365]
 [<c012f762>] sys_init_module+0x132/0x1c0
 [<c0102c89>] syscall_call+0x7/0xb
PCI: Found IRQ 11 for device 0000:00:03.0
PCI: Sharing IRQ 11 with 0000:00:03.1
PCI: Sharing IRQ 11 with 0000:01:00.0
Yenta: CardBus bridge found at 0000:00:03.0 [1014:0138]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:03.0, mfunc 0x00002000, devctl 0x64
Yenta: ISA IRQ mask 0x0698, PCI irq 11
Socket status: 30000006
PCI: Found IRQ 11 for device 0000:00:03.1
PCI: Sharing IRQ 11 with 0000:00:03.0
PCI: Sharing IRQ 11 with 0000:01:00.0
Yenta: CardBus bridge found at 0000:00:03.1 [1014:0138]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:03.1, mfunc 0x00002000, devctl 0x64
Yenta: ISA IRQ mask 0x0698, PCI irq 11
Socket status: 30000006
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x2f8-0x2ff
cs: IO port probe 0x100-0x3af: excluding 0x2f8-0x2ff
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 11 for device 0000:00:02.2
uhci_hcd 0000:00:02.2: Intel Corporation 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:02.2: irq 11, io base 0x0000fca0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 5 for device 0000:00:07.0
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
PCI: Found IRQ 11 for device 0000:00:02.2
PCI: Found IRQ 11 for device 0000:00:02.2
PCI: Found IRQ 11 for device 0000:00:03.0
PCI: Sharing IRQ 11 with 0000:00:03.1
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Found IRQ 11 for device 0000:00:03.1
PCI: Sharing IRQ 11 with 0000:00:03.0
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Found IRQ 5 for device 0000:00:07.0
usb 1-1: new full speed USB device using uhci_hcd and address 2
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
  Vendor: PNY       Model: USB 2.0 FD        Rev: 1.13
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 250880 512-byte hdwr sectors (128 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 250880 512-byte hdwr sectors (128 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
 sda: sda1 sda4
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: device scan complete
kjournald starting.  Commit interval 5 seconds
-------------- next part --------------
Linux version 2.6.13 (root at igloo) (gcc version 3.4.4) #2 Tue Sep 20 01:57:03 GMT 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000bfd0000 (usable)
 BIOS-e820: 000000000bfd0000 - 000000000bfdf000 (ACPI data)
 BIOS-e820: 000000000bfdf000 - 000000000bfe0000 (ACPI NVS)
 BIOS-e820: 000000000bfe0000 - 000000000c000000 (reserved)
 BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
user-defined physical RAM map:
 user: 0000000000000000 - 000000000009fc00 (usable)
 user: 000000000009fc00 - 00000000000a0000 (reserved)
 user: 00000000000f0000 - 0000000000100000 (reserved)
 user: 0000000000100000 - 000000000bfd0000 (usable)
0MB HIGHMEM available.
191MB LOWMEM available.
On node 0 totalpages: 49104
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 45008 pages, LIFO batch:15
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
Allocating PCI resources starting at 0c000000 (gap: 0bfd0000:f4030000)
Built 1 zonelists
Kernel command line: ro root=/dev/hda3 mem=196416K
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 364.031 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 191452k/196416k available (1612k kernel code, 4456k reserved, 682k data, 208k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 729.18 BogoMIPS (lpj=1458360)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Mobile Pentium II stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd880, last bus=7
PCI: Using configuration type 1
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fe700
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xe724, dseg 0xf0000
PnPBIOS: 23 nodes reported by PnP BIOS; 23 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
  IO window: d000-dfff
  MEM window: 70000000-dfffffff
  PREFETCH window: e0000000-f7ffffff
PCI: Bus 2, cardbus bridge: 0000:00:02.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 0c000000-0dffffff
  MEM window: 0e000000-0fffffff
PCI: Bus 6, cardbus bridge: 0000:00:02.1
  IO window: 00001800-000018ff
  IO window: 00001c00-00001cff
  PREFETCH window: 10000000-11ffffff
  MEM window: 12000000-13ffffff
PCI: Found IRQ 11 for device 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:06.0
PCI: Sharing IRQ 11 with 0000:01:00.0
PCI: Found IRQ 11 for device 0000:00:02.1
TC classifier action (bugs to netdev at vger.kernel.org cc hadi at cyberus.ca)
pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0a: ioport range 0x15e0-0x15ef has been reserved
pnp: 00:0a: ioport range 0xef00-0xefaf could not be reserved
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG MP0402H, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-C2102, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78242976 sectors (40060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
 hda: hda1 hda2 hda3 hda4
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 208k freed
input: PS/2 Generic Mouse on isa0060/serio1
Adding 136072k swap on /dev/hda2.  Priority:-1 extents:1
EXT3 FS on hda3, internal journal
Linux agpgart interface v0.101 (c) Dave Jones
hdc: ATAPI 20X DVD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Intel ISA PCIC probe: not found.
Device 'i82365.0' does not have a release() function, it is broken and must be fixed.
Badness in device_release at drivers/base/core.c:83
 [<c01ba599>] kobject_cleanup+0xa9/0xb0
 [<c01ba5a0>] kobject_release+0x0/0x10
 [<c01bafb5>] kref_put+0x45/0x90
 [<c01ba5cf>] kobject_put+0x1f/0x30
 [<c01ba5cf>] kobject_put+0x1f/0x30
 [<c01ba5a0>] kobject_release+0x0/0x10
 [<cc8013c9>] init_i82365+0x1c9/0x1df [i82365]
 [<c012f762>] sys_init_module+0x132/0x1c0
 [<c0102c89>] syscall_call+0x7/0xb
PCI: Found IRQ 11 for device 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:00:06.0
PCI: Sharing IRQ 11 with 0000:01:00.0
Yenta: CardBus bridge found at 0000:00:02.0 [1014:0000]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.0, mfunc 0xfba97543, devctl 0x62
Yenta: ISA IRQ mask 0x0698, PCI irq 11
Socket status: 30000006
PCI: Found IRQ 11 for device 0000:00:02.1
Yenta: CardBus bridge found at 0000:00:02.1 [1014:0000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:02.1, mfunc 0xfba97543, devctl 0x62
Yenta: ISA IRQ mask 0x0698, PCI irq 11
Socket status: 30000006
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x3f8-0x3ff
cs: IO port probe 0x3e0-0x4ff: excluding 0x3f8-0x3ff
cs: IO port probe 0x100-0x3af: excluding 0x130-0x137 0x200-0x207 0x220-0x22f 0x388-0x38f
cs: IO port probe 0x100-0x3af: excluding 0x130-0x137 0x200-0x207 0x220-0x22f 0x388-0x38f
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
PCI: Found IRQ 11 for device 0000:00:06.0
PCI: Sharing IRQ 11 with 0000:00:02.0
PCI: Sharing IRQ 11 with 0000:01:00.0
create - never read codec ready from AC'97
it is not probably bug, try to use CS4236 driver
Sound Fusion CS46xx: probe of 0000:00:06.0 failed with error -5
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
PCI: Found IRQ 11 for device 0000:00:07.2
uhci_hcd 0000:00:07.2: Intel Corporation 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00008400
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist
NFSD: starting 90-second grace period
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb 1-1: new full speed USB device using uhci_hcd and address 2
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
  Vendor: PNY       Model: USB 2.0 FD        Rev: 1.13
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 250880 512-byte hdwr sectors (128 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 250880 512-byte hdwr sectors (128 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
sda: assuming drive cache: write through
 sda: sda1 sda4
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: device scan complete
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.

More information about the linux-pcmcia mailing list