cardbus/pcmcia under fedora core 4
Storm
n.storm at web.de
Wed Jul 6 07:42:39 EDT 2005
sorry, had a messup and sent the wrong e-mail: here is the right one:
i have been attentively following your correspondence for the past
couple of weeks in my endeavour to find a solution to my problem. i have
posted to this list before with respect to another linux distribution
(suse 9.3). i have now turned to fedora core 4 hoping that there would
be no problems, but i seem to be in the same jam as before. i hope that
you will be patient with me. here is my problem:
i have a gericom laptop masterpiece 2440 xl.
system specifications:
p4 2.4 ghz
15'' tft display
ultra ata 40 gb hdd
512 mb ddr-ram
ati radeon 9000 mobility 64 mb
cardbus bridge ENE technology inc. cb 1410 cardbus controller
i am currently trying to correctly install pcmcia under fedora core on
this laptop, but to no avail. linux will load all pcmcia modules
(pcmcia, yenta_socket, pcmcia_core) without any messages in the system
logs. when i use cardmgr, the system freezes completely. thats the end
of story. i have excluded pcmcia from the bootup process to avoid
freezes during boot. kernel version is current: 2.6.12-1. output of
lspci -vv, dmesg and lsmod follows hereinafter:
1. lspci -vv:
00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller
(rev a0) (prog-if 00 [Generic])
Subsystem: Elitegroup Computer Systems: Unknown device b732
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 173 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at 1800 [size=256]
Region 1: I/O ports at 1c00 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS]
Sound Controller (rev a0)
Subsystem: Elitegroup Computer Systems: Unknown device b732
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 173 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at 1400 [size=256]
Region 1: I/O ports at 1080 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 1.0 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e8001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 1.0 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at e8002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 1.0 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin C routed to IRQ 10
Region 0: Memory at e8003000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0
Controller (prog-if 20 [EHCI])
Subsystem: Elitegroup Computer Systems: Unknown device b732
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 10
Region 0: Memory at e8004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI
Fast Ethernet (rev 91)
Subsystem: Elitegroup Computer Systems: Unknown device b732
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 173 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 4
Region 0: I/O ports at f800 [size=256]
Region 1: Memory at e8005000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller
Subsystem: Elitegroup Computer Systems: Unknown device b732
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size 20
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 20000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20400000-207ff000 (prefetchable)
Memory window 1: 20800000-20bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt-
PostWrite+
16-bit legacy interface ports at 0001
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 Lf
[FireGL 9000] (rev 01) (prog-if 00 [VGA])
Subsystem: Elitegroup Computer Systems: Unknown device b732
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size 04
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at e8100000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit-
FW- Rate=x1
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 Network controller: Intersil Corporation Intersil ISL3890 [Prism
GT/Prism Duette] (rev 01)
Subsystem: Netgear WG511 Wireless Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 7000ns max), Cache Line Size 20
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 20800000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
2. dmesg:
Linux version 2.6.12-1.1387_FC4 (bhcompile at decompose.build.redhat.com)
(gcc version 4.0.0 20050519 (Red Hat 4.0.0-8)) #1 Fri Jul 1 12:41:40 EDT
2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fdf0000 (usable)
BIOS-e820: 000000001fdf0000 - 000000001fdfb000 (ACPI data)
BIOS-e820: 000000001fdfb000 - 000000001fe00000 (ACPI NVS)
BIOS-e820: 000000001fe00000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
509MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 130544
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126448 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6ac0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fdf7446
ACPI: FADT (v001 ECS G732 0x06040000 PTL 0x000f4240) @ 0x1fdfaf8c
ACPI: DSDT (v001 PTLTD ECS 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
Allocating PCI resources starting at 20000000 (gap: 20000000:dff80000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ ide=nodma rhgb quiet
ide_setup: ide=nodma : Prevented DMA
Initializing CPU#0
CPU 0 irqstacks, hard=c0455000 soft=c0454000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 2390.838 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512180k/522176k available (2507k kernel code, 9364k reserved,
689k data, 184k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4734.97 BogoMIPS (lpj=2367488)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febf9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: After vendor identify, caps: 3febf9ff 00000000 00000000 00000000
00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: 3febf1ff 00000000 00000000 00000080 00000000
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0800 (from 0e30)
checking if image is initramfs... it is
Freeing initrd memory: 1079k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd9b8, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Uncovering SIS962 that hid as a SIS503 (compatible=1)
Enabling SiS 96x SMBus.
PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *5 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *4 5 7 9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 4 5 10 11) *9
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 *10 11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 10 11) *9
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: Embedded Controller [EC] (gpe 26)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 9 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
PCI: Cannot allocate resource region 0 of device 0000:00:02.6
pnp: 00:03: ioport range 0x8000-0x808f could not be reserved
pnp: 00:03: ioport range 0x8000-0x807f could not be reserved
pnp: 00:03: ioport range 0x8090-0x80ff has been reserved
pnp: 00:03: ioport range 0x8100-0x81ef could not be reserved
pnp: 00:03: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:03: ioport range 0xfe00-0xfe00 has been reserved
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1120652495.673:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 6BD781E88D5E157
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 646 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 0) is a 8250
PCI: Enabling device 0000:00:02.6 (0000 -> 0001)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:02.6[C] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:02.5[A] -> Link [LNKA] -> GSI 5 (level, low)
-> IRQ 5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2008-0x200f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: HITACHI_DK23DA-40, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: QSI CD-RW/DVD-ROM SBW-241, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 6, 458752 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI wakeup devices:
PCI0 USB0 USB1 USB2 USB3 LAN PCI1 PCI2 CRD0 AC97
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 184k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Synaptics Touchpad, model: 1, fw: 5.9, id: 0xb54ab1, caps: 0x80471b/0x0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
security: 3 users, 6 roles, 813 types, 90 bools
security: 55 classes, 190178 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hda8, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for
labeling
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses
genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
floppy0: no floppy controllers found
sis900.c: v1.08.08 Jan. 22 2005
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 4
PCI: setting IRQ 4 as level-triggered
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKD] -> GSI 4 (level, low)
-> IRQ 4
0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xf800, IRQ 4, 00:50:eb:1d:42:4b.
ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
intel8x0_measure_ac97_clock: measured 49358 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:02.6[C] -> Link [LNKC] -> GSI 11 (level,
low) -> IRQ 11
i2c-sis96x version 1.0.0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x8100
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:03.3[D] -> Link [LNKH] -> GSI 10 (level,
low) -> IRQ 10
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.3: irq 10, io mem 0xe8004000
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] -> GSI 10 (level,
low) -> IRQ 10
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 10, io mem 0xe8001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:03.1[B] -> Link [LNKF] -> GSI 11 (level,
low) -> IRQ 11
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 11, io mem 0xe8002000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:03.2[C] -> Link [LNKG] -> GSI 10 (level,
low) -> IRQ 10
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:03.2: irq 10, io mem 0xe8003000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 9 (level, low)
-> IRQ 9
Yenta: CardBus bridge found at 0000:00:0a.0 [1019:b732]
Yenta: adjusting diagnostic: 40 -> 60
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x000c1002, devctl 0x44
Yenta: ISA IRQ mask 0x0000, PCI irq 9
Socket status: 30000006
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins at debian.org>
ACPI: PCI Interrupt 0000:00:02.3[B] -> Link [LNKB] -> GSI 9 (level, low)
-> IRQ 9
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[9]
MMIO=[e8000000-e80007ff] Max Packet=[2048]
spurious 8259A interrupt: IRQ7.
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03e3840(lo)
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ibm_acpi: hkey object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
EXT3 FS on hda8, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda6, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 1048784k swap on /dev/hda7. Priority:-1 extents:1
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses
genfs_contexts
eth0: Media Link On 100mbps full-duplex
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
eth0: no IPv6 routers present
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 5 (level, low)
-> IRQ 5
[drm] Initialized radeon 1.16.0 20050311 on minor 0:
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Loading R200 Microcode
application mixer_applet2 uses obsolete OSS audio interface
Loaded prism54 driver, version 1.2
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 9 (level, low)
-> IRQ 9
3. lsmod:
Module Size Used by
prism54 56013 0
radeon 76481 1
drm 70101 2 radeon
parport_pc 28933 1
lp 13001 0
parport 40585 2 parport_pc,lp
autofs4 29253 2
rfcomm 42333 0
l2cap 30661 5 rfcomm
bluetooth 56133 4 rfcomm,l2cap
sunrpc 167813 1
dm_mod 58101 0
video 15941 0
button 6609 0
battery 9413 0
ac 4805 0
md5 4033 1
ipv6 267841 8
ohci1394 41353 0
ieee1394 304441 1 ohci1394
yenta_socket 21449 1
rsrc_nonstatic 12737 1 yenta_socket
pcmcia_core 50909 2 yenta_socket,rsrc_nonstatic
ohci_hcd 26849 0
ehci_hcd 41037 0
shpchp 94405 0
i2c_sis96x 5445 0
i2c_core 21569 1 i2c_sis96x
snd_intel8x0m 19589 0
snd_intel8x0 34689 1
snd_ac97_codec 75961 2 snd_intel8x0m,snd_intel8x0
snd_seq_dummy 3653 0
snd_seq_oss 37057 0
snd_seq_midi_event 9153 1 snd_seq_oss
snd_seq 62288 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 8781 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 51185 0
snd_mixer_oss 17857 1 snd_pcm_oss
snd_pcm 100169 4
snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 33605 2 snd_seq,snd_pcm
snd 57157 12
snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 10913 1 snd
snd_page_alloc 9669 3 snd_intel8x0m,snd_intel8x0,snd_pcm
sis900 22977 0
mii 5441 1 sis900
joydev 9601 0
ext3 132681 2
jbd 86233 1 ext3
More information about the linux-pcmcia
mailing list