VIA Epia MII 12000 LVDS, unable to apply power
Jaroslaw Zachwieja
grok at tnt.pl
Wed Jan 26 19:30:52 EST 2005
Hello All,
I've got the known error about pcmcia being "unable to apply power".
Googling got me to this list. So here's the information requested on
http://pcmcia.arm.linux.org.uk/.
The suggested fix from
http://forums.viaarena.com/messageview.cfm?catid=32&threadid=57796
did not work. Despite the "reserve=0xde010000,0x10000" appended to kernel
(these were the values reported by dmesg).
I've applied a patch mentioned in the same thread. No change, same error
messages (unable to apply power and PCI: Failed to allocate mem)
The kernel I'm running is the latest updated 2.6.8.1-24mdk (or -24mdkcustom
after applying the patch and rebuilding), other installed packages are
pcmcia-cs-3.2.8-1mdk and pcmcia-cs-3.2.8-1mdk.
This behaviour can be reproduced with both open source supported cards like
prism2/orinoco, rtl8139 and fancy netgear wg511v2 that is ndiswrapper driven.
All cards are verified working with my laptop (old tosh portege).
1. Machine type:
This is new VIA Epia MII 12000 board. This mini-itx board has PCMCIA slot
installed.
2. Cardbus bridge type:
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
3. Full lspci -vv output: http://tinyurl.com/5sa8z (or attached)
4. cbdump output: http://tinyurl.com/682h4 (or attached)
5. dmesg output: http://tinyurl.com/4m74w (or attached)
Could some knowledgeable people shed some light at the problem? The MII 6, 10
and 12k motherboards are quite popular in mini-itx world and I think, that
there might be more people banging their heads against this list... Is there
work in progress on this issue? Should a fix be expected?
I've subscribed here and searched the archives. I've also checked if cardmgr
is running (it is). I will stay tuned for any possible suggestions. If you
need any more information, feel free to ask.
Best regards,
--
Jaroslaw Zachwieja
pgp key at http://pgp.mit.edu
-------------- next part --------------
00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d8000000-dbffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 12
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: de001000-de002000 (prefetchable)
Memory window 1: de003000-de004000
I/O window 0: 00009000-00009403
I/O window 1: 00009800-00009c03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 5
Region 0: Memory at de005000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: de006000-de007000 (prefetchable)
Memory window 1: de008000-de009000
I/O window 0: 0000a000-0000a403
I/O window 1: 0000a800-0000ac03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at b000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin C routed to IRQ 7
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 4
Region 0: Memory at de00a000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at bc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 7
Region 0: I/O ports at c000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at de00b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at de00c000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at de00d000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics (rev 03) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 12
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
-------------- next part --------------
00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II
-- generic cardbus config registers
Vendor ID [00] : 0x1180
Device ID [02] : 0x0476
PCI command [04] : 0x0007
Base address [10] : 0xde005000
Memory Base 0 [1c] : 0xde006000
Memory Limit 0 [20] : 0xde007000
Memory Base 1 [24] : 0xde008000
Memory Limit 1 [28] : 0xde009000
IO Base 0 [2c] : 0x0000a000
IO Limit 0 [30] : 0x0000a400
IO Base 1 [34] : 0x0000a800
IO Limit 1 [38] : 0x0000ac00
Bridge control [3e] : 0x0580
Subsystem vendor ID [40] : 0x1106
Subsystem device ID [42] : 0xaa01
Legacy mode base [44] : 0x0001
-- Ricoh RL5c476II specific config registers
System configuration [80] : 0x0001
Misc Control [82] : 0x08a0
16-bit Interface Control [84] : 0x0300
16-bit I/O Timing 0 [88] : 0x0463
16-bit Memory Timing 0 [8a] : 0x0463
DMA Slave [90] : 0x0000
Misc Control 2 [a0] : 0x0000
Misc Control 3 [a2] : 0x0000
Misc Control 4 [a4] : 0x0000
GPIO 1 [aa] : 0x00
-- cardbus registers
CB_SOCKET_EVENT [00] : 0x00000000
CB_SOCKET_MASK [04] : 0x00000006
CB_SOCKET_STATE [08] : 0x30000006
CB_SOCKET_FORCE [0c] : 0x00000000
CB_SOCKET_CONTROL [10] : 0x00000400
CB_SOCKET_POWER [20] : 0x00000000
-- exca registers
I365_IDENT [00] : 0x83
I365_STATUS [01] : 0x33
I365_POWER [02] : 0x40
I365_INTCTL [03] : 0x40
I365_CSC [04] : 0x00
I365_CSCINT [05] : 0x08
I365_ADDRWIN [06] : 0x00
I365_IOCTL [07] : 0x00
I365_GENCTL [16] : 0x0000
I365_GBLCTL [1e] : 0x0000
I365_IO0_START [08] : 0x0000
I365_IO0_STOP [0a] : 0x0001
I365_IO1_START [0c] : 0x0000
I365_IO1_STOP [0e] : 0x0001
I365_MEM0_START [10] : 0x0000
I365_MEM0_STOP [12] : 0x0000
I365_MEM0_OFF [14] : 0x0000
I365_MEM0_PAGE [40] : 0x00
I365_MEM1_START [18] : 0x0000
I365_MEM1_STOP [1a] : 0x0000
I365_MEM1_OFF [1c] : 0x0000
I365_MEM1_PAGE [41] : 0x00
I365_MEM2_START [20] : 0x0000
I365_MEM2_STOP [22] : 0x0000
I365_MEM2_OFF [24] : 0x0000
I365_MEM2_PAGE [42] : 0x00
I365_MEM3_START [28] : 0x0000
I365_MEM3_STOP [2a] : 0x0000
I365_MEM3_OFF [2c] : 0x0000
I365_MEM3_PAGE [43] : 0x00
I365_MEM4_START [30] : 0x0000
I365_MEM4_STOP [32] : 0x0000
I365_MEM4_OFF [34] : 0x0000
I365_MEM4_PAGE [44] : 0x00
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II
-- generic cardbus config registers
Vendor ID [00] : 0x1180
Device ID [02] : 0x0476
PCI command [04] : 0x0007
Base address [10] : 0xde000000
Memory Base 0 [1c] : 0xde001000
Memory Limit 0 [20] : 0xde002000
Memory Base 1 [24] : 0xde003000
Memory Limit 1 [28] : 0xde004000
IO Base 0 [2c] : 0x00009000
IO Limit 0 [30] : 0x00009400
IO Base 1 [34] : 0x00009800
IO Limit 1 [38] : 0x00009c00
Bridge control [3e] : 0x0500
Subsystem vendor ID [40] : 0x1106
Subsystem device ID [42] : 0xaa01
Legacy mode base [44] : 0x0001
-- Ricoh RL5c476II specific config registers
System configuration [80] : 0x0001
Misc Control [82] : 0x08a0
16-bit Interface Control [84] : 0x0300
16-bit I/O Timing 0 [88] : 0x0463
16-bit Memory Timing 0 [8a] : 0x0463
DMA Slave [90] : 0x0000
Misc Control 2 [a0] : 0x0000
Misc Control 3 [a2] : 0x0000
Misc Control 4 [a4] : 0x0000
GPIO 1 [aa] : 0x00
-- cardbus registers
CB_SOCKET_EVENT [00] : 0x00000000
CB_SOCKET_MASK [04] : 0x00000006
CB_SOCKET_STATE [08] : 0x30000820
CB_SOCKET_FORCE [0c] : 0x00000000
CB_SOCKET_CONTROL [10] : 0x00000400
CB_SOCKET_POWER [20] : 0x00000000
-- exca registers
I365_IDENT [00] : 0x83
I365_STATUS [01] : 0x3f
I365_POWER [02] : 0x40
I365_INTCTL [03] : 0x40
I365_CSC [04] : 0x00
I365_CSCINT [05] : 0x08
I365_ADDRWIN [06] : 0x00
I365_IOCTL [07] : 0x00
I365_GENCTL [16] : 0x0000
I365_GBLCTL [1e] : 0x0000
I365_IO0_START [08] : 0x0000
I365_IO0_STOP [0a] : 0x0001
I365_IO1_START [0c] : 0x0000
I365_IO1_STOP [0e] : 0x0001
I365_MEM0_START [10] : 0x0000
I365_MEM0_STOP [12] : 0x0000
I365_MEM0_OFF [14] : 0x0000
I365_MEM0_PAGE [40] : 0x00
I365_MEM1_START [18] : 0x0000
I365_MEM1_STOP [1a] : 0x0000
I365_MEM1_OFF [1c] : 0x0000
I365_MEM1_PAGE [41] : 0x00
I365_MEM2_START [20] : 0x0000
I365_MEM2_STOP [22] : 0x0000
I365_MEM2_OFF [24] : 0x0000
I365_MEM2_PAGE [42] : 0x00
I365_MEM3_START [28] : 0x0000
I365_MEM3_STOP [2a] : 0x0000
I365_MEM3_OFF [2c] : 0x0000
I365_MEM3_PAGE [43] : 0x00
I365_MEM4_START [30] : 0x0000
I365_MEM4_STOP [32] : 0x0000
I365_MEM4_OFF [34] : 0x0000
I365_MEM4_PAGE [44] : 0x00
-------------- next part --------------
Linux version 2.6.8.1-24mdk (qateam at updates.mandrakesoft.com) (gcc version 3.4.1 (Mandrakelinux 10.1 3.4.1-4mdk)) #1 Fri Jan 14 03:01:00 MST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000dff0000 (usable)
BIOS-e820: 000000000dff0000 - 000000000dff3000 (ACPI NVS)
BIOS-e820: 000000000dff3000 - 000000000e000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
223MB LOWMEM available.
On node 0 totalpages: 57328
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 53232 pages, LIFO batch:12
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VT9174 ) @ 0x000f6570
ACPI: RSDT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3000
ACPI: FADT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0dff3040
ACPI: DSDT (v001 VT9174 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Built 1 zonelists
No local APIC present or hardware disabled
Initializing CPU#0
Kernel command line: BOOT_IMAGE=2681-24 ro root=301 acpi=ht resume=/dev/hda8 splash=silent reserve=0xde010000,0x10000
bootsplash: silent mode.
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1200.283 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 223404k/229312k available (1861k kernel code, 5236k reserved, 580k data, 200k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2375.68 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 0381b93f 00000000 00000000 00000000
CPU: Centaur VIA Nehemiah stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
init init/main.c:689
init init/main.c:702
init init/main.c:707
do_pre_smp_initcalls init/main.c:653
do_pre_smp_initcalls init/main.c:659
init init/main.c:711
init init/main.c:714
init init/main.c:716
init init/main.c:718
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
ACPI: Looking for DSDT in initrd ... not found!
Freeing initrd memory: 156k freed
init init/main.c:724
do_basic_setup init/main.c:634
do_basic_setup init/main.c:636
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Disabled
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/3177] at 0000:00:11.0
vesafb: probe of vesafb0 failed with error -6
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1106773513.795:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xbc00-0xbc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: Maxtor 4A250J0, ATA DISK drive
hdb: _NEC DVD_RW ND-2510A, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 1024KiB
hda: 490234752 sectors (251000 MB) w/2048KiB Cache, CHS=30515/255/63, UDMA(133)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 >
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
init init/main.c:726
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 156KiB [1 disk] into ram disk... |/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 200k freed
EXT3 FS on hda1, internal journal
Adding 1124508k swap on /dev/hda8. Priority:-1 extents:1
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 4 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
PCI: Found IRQ 5 for device 0000:00:14.0
PCI: Sharing IRQ 5 with 0000:00:0a.1
PCI: Sharing IRQ 5 with 0000:00:14.1
bttv0: Bt878 (rev 17) at 0000:00:14.0, irq: 5, latency: 32, mmio: 0xde00c000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
bttv0: Hauppauge eeprom: model=44915, tuner=Philips FM1246 (1), radio=yes
bttv0: using tuner=1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951),ta8874z
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 1 (Philips PAL_I (FI1246 and compatibles)) by bt878 #0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: Maximum main memory to use for agp memory: 176M
agpgart: AGP aperture is 128M @ 0xd0000000
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
loop: loaded (max 8 devices)
hdb: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
eth0: VIA Rhine II at 0xc800, 00:40:63:db:74:52, IRQ 12.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Found IRQ 12 for device 0000:00:0a.0
Yenta: CardBus bridge found at 0000:00:0a.0 [1106:aa01]
Yenta: ISA IRQ mask 0x0c08, PCI irq 12
Socket status: 30000820
PCI: Found IRQ 5 for device 0000:00:0a.1
PCI: Sharing IRQ 5 with 0000:00:14.0
PCI: Sharing IRQ 5 with 0000:00:14.1
Yenta: CardBus bridge found at 0000:00:0a.1 [1106:aa01]
Yenta: ISA IRQ mask 0x0c08, PCI irq 5
Socket status: 30000006
PCI: Failed to allocate mem resource #0:10000 at de010000 for 0000:02:00.0
PCI: Failed to allocate mem resource #1:10000 at de010000 for 0000:02:00.0
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x370-0x377 0x400-0x47f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
inserting floppy driver for 2.6.8.1-24mdk
floppy0: no floppy controllers found
inserting floppy driver for 2.6.8.1-24mdk
floppy0: no floppy controllers found
NET: Registered protocol family 17
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
PCI: Setting latency timer of device 0000:00:11.5 to 64
cs: pcmcia_socket0: unable to apply power.
PCI: Failed to allocate mem resource #0:10000 at de010000 for 0000:02:00.0
PCI: Failed to allocate mem resource #1:10000 at de010000 for 0000:02:00.0
More information about the linux-pcmcia
mailing list