cs: pcmcia_socket0: unable to apply power problem

[Leppänen Marko]

Hi,

I got an old laptop, Compaq Armada 1750 and installed Ubuntu Breezy ( 
with kernel 2.6.12-10-686) on it. 
If I install my SMC2635W PCMCIA card in, the kernel says the familiar
cs: pcmcia_socket0: unable to apply power
error.
The laptop seems to have the TI PCI1225 bridge.


The lspci -dump
--->8---

0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
  	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
  	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
  	Latency: 0
  	Region 0: Memory at 44000000 (32-bit, prefetchable) [size=64M]
  	Capabilities: [a0] AGP version 1.0
  		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x2
  		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2

0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) (prog-if 00 [Normal decode])
  	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
  	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
  	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
  	I/O behind bridge: 00001000-00001fff
  	Memory behind bridge: 40000000-410fffff
  	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+

0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
  	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
  	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
  	Latency: 0

0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
  	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
  	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
  	Latency: 0
  	Region 4: I/O ports at 2020 [size=16]

0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
  	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
  	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
  	Latency: 64
  	Interrupt: pin D routed to IRQ 11
  	Region 4: I/O ports at 2000 [size=32]

0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
  	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
  	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
  	Interrupt: pin ? routed to IRQ 9

0000:00:11.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
  	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
  	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
  	Latency: 168, Cache Line Size: 0x08 (32 bytes)
  	Interrupt: pin A routed to IRQ 11
  	Region 0: Memory at 7fffe000 (32-bit, non-prefetchable) [size=4K]
  	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
  	Memory window 0: 08000000-083ff000 (prefetchable)
  	Memory window 1: 08400000-087ff000
  	I/O window 0: 00004000-000040ff
  	I/O window 1: 00004400-000044ff
  	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
  	16-bit legacy interface ports at 0001

0000:00:11.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
  	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
  	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
  	Latency: 168, Cache Line Size: 0x08 (32 bytes)
  	Interrupt: pin B routed to IRQ 0
  	Region 0: Memory at 7ffff000 (32-bit, non-prefetchable) [size=4K]
  	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
  	Memory window 0: 08800000-08bff000 (prefetchable)
  	Memory window 1: 08c00000-08fff000
  	I/O window 0: 00004800-000048ff
  	I/O window 1: 00004c00-00004cff
  	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
  	16-bit legacy interface ports at 0001

0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage LT Pro AGP-133 (rev dc) (prog-if 00 [VGA])
  	Subsystem: ATI Technologies Inc Rage LT Pro AGP 2X
  	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
  	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
  	Latency: 0 (2000ns min)
  	Interrupt: pin A routed to IRQ 11
  	Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=16M]
  	Region 1: I/O ports at 1000 [size=256]
  	Region 2: Memory at 41000000 (32-bit, non-prefetchable) [size=4K]
  	Capabilities: [50] AGP version 1.0
  		Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
  		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x2
  	Capabilities: [5c] Power Management version 1
  		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
  		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

-- 
Marko Leppänen