32-bit pc card cannot be seen
Joo Ghee
jooghee at gmail.com
Mon Dec 5 02:31:02 EST 2005
Hi,
I have just installed Linux (Debian Sarge, Kernel 2.6.8-2-386) on a
laptop. However, the laptop was not able to identify a 32-bit pc card
(a wireless LAN card) that I plug into the cardbus slot. It works
fine with a 16-bit pcmcia card, so I am not sure what is the problem.
Below are the dmesg and lspci -v of my system. Would really
appreciate if someone could point me to what could be the problem.
Rgds,
Joo Ghee
# dmesg
Linux version 2.6.8-2-386 (horms at tabatha.lab.ultramonkey.org) (gcc
version 3.3.5 (Debian 1:3.3.5-12)) #1 Thu May 19 17:40:50 JST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f6e0000 (usable)
BIOS-e820: 000000000f6e0000 - 000000000f6ea000 (ACPI data)
BIOS-e820: 000000000f6ea000 - 000000000f700000 (ACPI NVS)
BIOS-e820: 000000000f700000 - 0000000010000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
246MB LOWMEM available.
On node 0 totalpages: 63200
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 59104 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7a10
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x0f6e5e41
ACPI: FADT (v002 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x0f6e9e78
ACPI: MADT (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x0f6e9efc
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x0f6e9fd8
ACPI: MCFG (v001 INTEL ALVISO 0x06040000 LOHR 0x0000005f) @ 0x0f6e9f9c
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030224) @ 0x0f6e6078
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x0f6e5e7d
ACPI: DSDT (v001 INTEL ALVISO 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: Skipping IOAPIC probe due to 'noapic' option.
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro noapic nolapic
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1496.718 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 243156k/252800k available (1336k kernel code, 8912k reserved,
732k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2949.12 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040
CPU: Intel(R) Celeron(R) M processor 1.50GHz stepping 08
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4216k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd70e, last bus=6
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 *11)
ACPI: Embedded Controller [EC0] (gpe 23)
ACPI-0347: *** Error: Handler for [EmbeddedControl] returned AE_TIME
ACPI-1133: *** Error: Method execution failed
[\_SB_.PCI0.LPCB.EC0_.BAT0._STA] (Node cf674540), AE_TIME
ACPI-0154: *** Error: Method execution failed
[\_SB_.PCI0.LPCB.EC0_.BAT0._STA] (Node cf674540), AE_TIME
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7a40
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc089, dseg 0x400
pnp: 00:00: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:00: ioport range 0x1000-0x105f has been reserved
pnp: 00:00: ioport range 0x1060-0x107f has been reserved
pnp: 00:00: ioport range 0x1180-0x11bf has been reserved
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1e.2[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:1e.3[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:06:05.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI interrupt 0000:06:07.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
ACPI: PCI interrupt 0000:06:09.0[A] -> GSI 10 (level, low) -> IRQ 10
Simple Boot Flag at 0x37 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ACPI: PCI interrupt 0000:00:1e.3[B] -> GSI 10 (level, low) -> IRQ 10
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 3
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4216 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 10 (level, low) -> IRQ 10
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:DMA
hda: HTS424040M9AT00, ATA DISK drive
hdb: TSSTcorpCDW/DVD TS-L462C, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/1739KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 > p3
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 722852k swap on /dev/hda6. Priority:-1 extents:1
EXT3 FS on hda3, internal journal
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Synaptics Touchpad, model: 1
Firmware: 6.2
Sensor: 18
new absolute packet format
Touchpad has extended capability bits
-> 4 multi-buttons, i.e. besides standard buttons
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
Capability LSM initialized
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:06:09.0[A] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:06:09.0 [1025:006a]
Yenta: adjusting diagnostic: 00 -> 60
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:06:09.0, mfunc 0x00001022, devctl 0x44
Yenta: ISA IRQ mask 0x0070, PCI irq 10
Socket status: 30000006
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:06:07.0[A] -> GSI 10 (level, low) -> IRQ 10
eth0: RealTek RTL8139 at 0x3000, 00:0a:e4:e1:e8:a4, IRQ 10
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: Intel Corp. I/O Controller Hub USB
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 00001820
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: Intel Corp. I/O Controller Hub USB
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 00001840
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: Intel Corp. I/O Controller Hub USB
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 11, io base 00001860
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.3: Intel Corp. I/O Controller Hub USB
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 11, io base 00001880
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: Intel Corp. I/O Controller Hub USB2
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 11, pci mem d00a0000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 5-7: new high speed USB device using address 2
hw_random hardware driver 1.0.0 loaded
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: USB Model: Flash Disk Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
USB Mass Storage device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
Intel 810 + AC97 Audio, version 1.01, 17:47:33 May 19 2005
ACPI: PCI interrupt 0000:00:1e.2[A] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1e.2 to 64
i810: Intel ICH4 found at IO 0x18c0 and 0x1c00, MEM 0xb0040800 and
0xb0040400, IRQ 10
i810: Intel ICH4 mmio at 0xd00a8800 and 0xd00cc400
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 codec, id: ALG96 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not
present), total channels = 2
i810_audio: setting clocking to 48689
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
Real Time Clock Driver v1.12
input: PC Speaker
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
NET: Registered protocol family 17
cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: excluding 0x800-0x80f
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02cc960(lo)
IPv6 over IPv4 tunneling driver
mtrr: no more MTRRs available
eth0: no IPv6 routers present
# lspci -v
0000:00:00.0 Host bridge: Intel Corp. Mobile Memory Controller Hub (rev 03)
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] #09 [3109]
0000:00:02.0 VGA compatible controller: Intel Corp. Mobile Graphics
Controller (rev 03) (prog-if 00 [VGA])
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at b0080000 (32-bit, non-prefetchable) [size=512K]
I/O ports at 1800 [size=8]
Memory at c0000000 (32-bit, prefetchable) [size=256M]
Memory at b0000000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
0000:00:02.1 Display controller: Intel Corp. Mobile Graphics Controller (rev 03)
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: fast devsel
Memory at 10000000 (32-bit, non-prefetchable) [disabled] [size=512K]
Capabilities: [d0] Power Management version 2
0000:00:1d.0 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1820 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1840 [size=32]
0000:00:1d.2 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1860 [size=32]
0000:00:1d.3 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1880 [size=32]
0000:00:1d.7 USB Controller: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 0, IRQ 11
Memory at b0040000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] #0a [20a0]
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev d3)
(prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: b0100000-b01fffff
Capabilities: [50] #0d [0000]
0000:00:1e.2 Multimedia audio controller: Intel Corp.
82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 0, IRQ 10
I/O ports at 1c00 [size=256]
I/O ports at 18c0 [size=64]
Memory at b0040800 (32-bit, non-prefetchable) [size=512]
Memory at b0040400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:00:1e.3 Modem: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family)
AC'97 ModemController (rev 03) (prog-if 00 [Generic])
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: medium devsel, IRQ 10
I/O ports at 2400 [size=256]
I/O ports at 2000 [size=128]
Capabilities: [50] Power Management version 2
0000:00:1f.0 ISA bridge: Intel Corp. 82801FBM (ICH6M) LPC Interface
Bridge (rev03)
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 0
0000:00:1f.1 IDE interface: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6
Family) IDEController (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 0, IRQ 10
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at 1810 [size=16]
0000:00:1f.3 SMBus: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family)
SMBus Controller (rev 03)
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: medium devsel, IRQ 11
I/O ports at 20a0 [size=32]
0000:06:05.0 Network controller: Broadcom Corporation: Unknown device
4318 (rev02)
Subsystem: AMBIT Microsystem Corp.: Unknown device 0312
Flags: bus master, fast devsel, latency 32, IRQ 10
Memory at b0100000 (32-bit, non-prefetchable) [size=8K]
0000:06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at 3000 [size=256]
Memory at b0102000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
0000:06:09.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus
Controller (rev 01)
Subsystem: Acer Incorporated [ALI]: Unknown device 006a
Flags: bus master, medium devsel, latency 168, IRQ 10
Memory at 10080000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001
More information about the linux-pcmcia
mailing list