RaLink 2500 not allocated memory / ENE CB1410 cardbus

Brandon Long blong at skycon.net
Wed Aug 24 12:49:03 EDT 2005


I am having an issue with my rt2500 card not getting allocated any memory or 
irq by the kernel, using a ENE CB1410 cardbus controller, with yenta socket 
and wireless extensions compiled into the kernel. Using Ubuntu for AMD64.

The module compiles cleanly and loads cleanly, but when I try to ifup ra0 i 
get device not found.

here is full lspci -vv output: (with pci=routeirq as grub arg)
previously without that the Ralink device would get routed irq0

0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host 
Bridge (rev 01)
        Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 64
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
        Capabilities: [80] AGP version 3.5
                Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh- GART64- HTrans- 
64bit- FW- AGP3+ Rate=x4,x8
                Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- 
Rate=x8
        Capabilities: [c0] #08 [0060]
        Capabilities: [68] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] #08 [8001]

0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800 
South] (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00002000-00002fff
        Memory behind bridge: d0100000-d01fffff
        Prefetchable memory behind bridge: d8000000-dfffffff
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:05.0 Network controller: RaLink Ralink RT2500 802.11 Cardbus Reference 
Card (rev 01)
        Subsystem: Micro-Star International Co., Ltd.: Unknown device 6833
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at <ignored> (32-bit, non-prefetchable) [disabled]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 
Controller (PHY/Link) (prog-if 10 [OHCI])
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (500ns min, 1000ns max), Cache Line Size: 0x10 (64 bytes)
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at d0008000 (32-bit, non-prefetchable) [size=2K]
        Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+

0000:00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 
Gigabit Ethernet (rev 10)
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 0x10 (64 
bytes)
        Interrupt: pin A routed to IRQ 19
        Region 0: I/O ports at 1000 [size=256]
        Region 1: Memory at d0008800 (32-bit, non-prefetchable) [size=256]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0c.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 
01)
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 168, Cache Line Size: 0x10 (64 bytes)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
        Memory window 0: 40400000-407ff000 (prefetchable)
        Memory window 1: 40800000-40bff000
        I/O window 0: 00004400-000044ff
        I/O window 1: 00004800-000048ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
        16-bit legacy interface ports at 0001

0000:00:0e.0 Unknown mass storage controller: Winbond Electronics Corp: 
Unknown device 8481 (rev 01)
        Subsystem: Winbond Electronics Corp: Unknown device 1050
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at d0005000 (32-bit, non-prefetchable) [size=4K]
        Region 1: Memory at d0004000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA 
PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0e.1 Unknown mass storage controller: Winbond Electronics Corp: 
Unknown device 8482 (rev 01)
        Subsystem: Winbond Electronics Corp: Unknown device 1050
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at d0007000 (32-bit, non-prefetchable) [size=4K]
        Region 1: Memory at d0006000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA 
PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 80) (prog-if 00 [UHCI])
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x10 (64 bytes)
        Interrupt: pin A routed to IRQ 21
        Region 4: I/O ports at 1c00 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 80) (prog-if 00 [UHCI])
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x10 (64 bytes)
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at 1c20 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 80) (prog-if 00 [UHCI])
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x10 (64 bytes)
        Interrupt: pin C routed to IRQ 21
        Region 4: I/O ports at 1c40 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 
20 [EHCI])
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, Cache Line Size: 0x10 (64 bytes)
        Interrupt: pin D routed to IRQ 21
        Region 0: Memory at d0008c00 (32-bit, non-prefetchable) [size=256]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA 
PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping+ SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.1 IDE interface: VIA Technologies, Inc. 
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a 
[Master SecP PriP])
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin A routed to IRQ 23
        Region 4: I/O ports at 1c60 [size=16]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. 
VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 22
        Region 0: I/O ports at 1400 [size=256]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 
Modem] (rev 80)
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 22
        Region 0: I/O ports at 1800 [size=256]
        Capabilities: [d0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Capabilities: [80] #08 [2101]

0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-

0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-

0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-

0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility 
Radeon 9600 M10] (prog-if 00 [VGA])
        Subsystem: CLEVO/KAPOK Computer: Unknown device 4701
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 66 (2000ns min), Cache Line Size: 0x10 (64 bytes)
        Interrupt: pin A routed to IRQ 9
        Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
        Region 1: I/O ports at 2000 [size=256]
        Region 2: Memory at d0100000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [58] AGP version 3.0
                Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 
64bit- FW+ AGP3+ Rate=x4,x8
                Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- 
Rate=<none>
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-



-- 
Brandon Long
SkyCon Networks -- http://www.skycon.net
blong at skycon.net



More information about the linux-pcmcia mailing list