VIA EPIA MII 6000, pcmcia_socket0: unable to apply power
Samuel Abels
newsgroups at debain.org
Fri Aug 5 17:17:52 EDT 2005
Hello,
I have a very similar problem to the one mentioned here:
http://lists.infradead.org/pipermail/linux-pcmcia/2004-October/001162.html
System: VIA EPIA MII-6000, 512 MB RAM
PCMCIA: Netgear WG511T (Wireless Network Card)
Bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Kernel: 2.6.10-5
The wireless network card in the PCMCIA adaptor won't show up and the
syslog contains error messages such as
"pcmcia_socket0: unable to apply power"
or
"Failed to allocate mem resource"
I have appended a the following files below:
lspci: Normal output of "lspci -vv"
iomem: Output of "cat /proc/iomem"
dmesg: dmesg after system bootup.
I then also tried appending "reserve=0x0e000000,0x02000000" to the
kernel boot options and fetched the same output again. See the appended
files that have "_reserved" appended to their file name.
I also tried to remove and reinsert the card after system bootup.
Removing did not cause any syslog messages, but on re-insertion it
gives:
Aug 4 22:17:18 knap kernel: cs: pcmcia_socket0: unable to apply power.
Aug 4 22:17:19 knap kernel: PCI: Failed to allocate mem resource #0:10000 at ea010000 for 0000:02:00.0
Aug 4 22:17:19 knap kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Aug 4 22:17:19 knap kernel: ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 12 (level, low) -> IRQ 12
Aug 4 22:17:19 knap kernel: ath_pci: cannot reserve PCI memory region
Aug 4 22:17:19 knap pci.agent[7893]: ath_pci: already loaded
Following this, I tried appending "reserve=0xea010000,0x10000" to the
kernel, but this did not change the behavior at all.
By appending "pci=routeirq" instead, the mem allocation errors
disappeared, leaving only the "unable to apply power" messages there.
Either way, the wireless network card would not show up in the "ifconfig
-a" output.
(Unfortunately, the cbdump utility does not seem to exist on my system,
so no output provided.)
If I can give you any other information, please let me know.
-Samuel
lspci:
***************************************************
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: e4000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 12
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 1e000000-1e3ff000 (prefetchable)
Memory window 1: ea003000-ea004000
I/O window 0: 00009000-00009403
I/O window 1: 00009800-00009c03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 7
Region 0: Memory at ea005000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: ea006000-ea007000 (prefetchable)
Memory window 1: ea008000-ea009000
I/O window 0: 0000a000-0000a403
I/O window 1: 0000a800-0000ac03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at b000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 7
Region 4: I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 7
Region 0: Memory at ea00a000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at bc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at c000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at ea00b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics (rev 03) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 12
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:02:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Netgear: Unknown device 4b00
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 12
Region 0: [virtual] Memory at ea010000 (32-bit, non-prefetchable) [size=ffff5000]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
dmesg:
**********************************************************
Linux version 2.6.10-5-386 (buildd at terranova) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #1 Thu Mar 24 14:43:04 GMT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dff0000 (usable)
BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS)
BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
479MB LOWMEM available.
On node 0 totalpages: 122864
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 118768 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VT9174 ) @ 0x000f6570
ACPI: RSDT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3000
ACPI: FADT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040
ACPI: DSDT (v001 VT9174 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro quiet splash
No local APIC present or hardware disabled
mapped APIC to ffffd000 (013c6000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 600.058 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 479172k/491456k available (1433k kernel code, 11636k reserved, 753k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1187.84 BogoMIPS (lpj=593920)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 00803135 80803035 00000000 00000000 00000000 00000000
CPU: Centaur VIA Samuel 2 stepping 03
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ACPI: setting ELCR to 0200 (from 12a0)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4236k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 4 5 6 7 *12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 4 5 6 *7 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 4 5 6 7 12) *9
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0x400-0x47f could not be reserved
pnp: 00:01: ioport range 0x500-0x50f has been reserved
audit: initializing netlink socket (disabled)
audit(1123207404.411:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
PCI0 USB0 USB1 USB2 USB3 USB4 USB5 USB6 LAN0 AC97 MC97 UAR1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4236KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 12 (level, low) -> IRQ 12
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xbc00-0xbc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: ST380021A, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
Probing IDE interface ide1...
hdd: CD-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Stopping tasks: ==|
Freeing memory... -\|/done (455 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 1413680k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdd: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
lp: driver loaded but no devices found
mice: PS/2 mouse device common for all mice
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins at debian.org>
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel at redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
hdd: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdd: packet command error: error=0x54
ide: failed opcode was 100
cdrom: open failed.
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.10-5-386
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: Maximum main memory to use for agp memory: 409M
agpgart: AGP aperture is 64M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 12 (level, low) -> IRQ 12
Yenta: CardBus bridge found at 0000:00:0a.0 [1106:aa01]
yenta 0000:00:0a.0: Preassigned resource 0 busy, reconfiguring...
Yenta: ISA IRQ mask 0x0c00, PCI irq 12
Socket status: 30000820
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI interrupt 0000:00:0a.1[B] -> GSI 7 (level, low) -> IRQ 7
Yenta: CardBus bridge found at 0000:00:0a.1 [1106:aa01]
Yenta: ISA IRQ mask 0x0c00, PCI irq 7
Socket status: 30000006
PCI: Failed to allocate mem resource #0:10000 at ea010000 for 0000:02:00.0
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.12.14 (AR5210, AR5211, AR5212)
wlan: 0.8.4.5 (EXPERIMENTAL)
ath_rate_onoe: 1.0
ath_pci: 0.9.4.12 (EXPERIMENTAL)
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 12 (level, low) -> IRQ 12
ath_pci: cannot reserve PCI memory region
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 12, io base 0xb000
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 7 (level, low) -> IRQ 7
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: irq 7, io base 0xb400
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: irq 5, io base 0xb800
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:10.0-2
input: USB HID v1.10 Device [Logitech USB Receiver] on usb-0000:00:10.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 7 (level, low) -> IRQ 7
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: irq 7, pci mem 0xea00a000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
usb 1-2: USB disconnect, address 2
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: can't resubmit intr, 0000:00:10.0-2/input1, status -19
usb 1-2: new low speed USB device using uhci_hcd and address 3
irda_init()
NET: Registered protocol family 23
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:10.0-2
input: USB HID v1.10 Device [Logitech USB Receiver] on usb-0000:00:10.0-2
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:11.5 to 64
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 12 (level, low) -> IRQ 12
eth0: VIA Rhine II at 0xc800, 00:40:63:dd:41:f4, IRQ 12.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link cde1.
eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
cs: IO port probe 0x0100-0x04ff: excluding 0x418-0x47f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
iomem:
***************************************************
00000000-0009ffff : System RAM
000a0000-000bffff : Video RAM area
000c0000-000cdfff : Video ROM
000f0000-000fffff : System ROM
00100000-1dfeffff : System RAM
00100000-0026676a : Kernel code
0026676b-00322bff : Kernel data
1dff0000-1dff2fff : ACPI Non-volatile Storage
1dff3000-1dffffff : ACPI Tables
1e000000-1e3fffff : PCI CardBus #02
e0000000-e3ffffff : 0000:00:00.0
e4000000-e7ffffff : PCI Bus #01
e4000000-e7ffffff : 0000:01:00.0
e8000000-e9ffffff : PCI Bus #01
e8000000-e8ffffff : 0000:01:00.0
ea000000-ea000fff : 0000:00:0a.0
ea000000-ea000fff : yenta_socket
ea003000-ea004fff : PCI CardBus #02
ea005000-ea005fff : 0000:00:0a.1
ea005000-ea005fff : yenta_socket
ea006000-ea007fff : PCI CardBus #06
ea008000-ea009fff : PCI CardBus #06
ea00a000-ea00a0ff : 0000:00:10.3
ea00a000-ea00a0ff : ehci_hcd
ea00b000-ea00b0ff : 0000:00:12.0
ea00b000-ea00b0ff : via-rhine
ffff0000-ffffffff : reserved
lspci_reserved:
*******************************************************
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e8000000-e9ffffff
Prefetchable memory behind bridge: e4000000-e7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 12
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 1e000000-1e3ff000 (prefetchable)
Memory window 1: ea003000-ea004000
I/O window 0: 00009000-00009403
I/O window 1: 00009800-00009c03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
0000:00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 7
Region 0: Memory at ea005000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: ea006000-ea007000 (prefetchable)
Memory window 1: ea008000-ea009000
I/O window 0: 0000a000-0000a403
I/O window 1: 0000a800-0000ac03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at b000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 7
Region 4: I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 7
Region 0: Memory at ea00a000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at bc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at c000 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at ea00b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics (rev 03) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock graphics
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 12
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
0000:02:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Netgear: Unknown device 4b00
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 12
Region 0: [virtual] Memory at ea010000 (32-bit, non-prefetchable) [size=ffff5000]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
dmesg_reserved:
************************************************************
Linux version 2.6.10-5-386 (buildd at terranova) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #1 Thu Mar 24 14:43:04 GMT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dff0000 (usable)
BIOS-e820: 000000001dff0000 - 000000001dff3000 (ACPI NVS)
BIOS-e820: 000000001dff3000 - 000000001e000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
479MB LOWMEM available.
On node 0 totalpages: 122864
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 118768 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VT9174 ) @ 0x000f6570
ACPI: RSDT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3000
ACPI: FADT (v001 VT9174 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dff3040
ACPI: DSDT (v001 VT9174 AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro reserve=0x0e000000,0x02000000 quiet splash
No local APIC present or hardware disabled
mapped APIC to ffffd000 (013c6000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 599.870 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 479172k/491456k available (1433k kernel code, 11636k reserved, 753k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1187.84 BogoMIPS (lpj=593920)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 00803135 80803035 00000000 00000000 00000000 00000000
CPU: Centaur VIA Samuel 2 stepping 03
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ACPI: setting ELCR to 0200 (from 12a0)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4236k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfb2d0, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 4 5 6 7 *12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 4 5 6 *7 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 4 *5 6 7 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 4 5 6 7 12) *9
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0x400-0x47f could not be reserved
pnp: 00:01: ioport range 0x500-0x50f has been reserved
audit: initializing netlink socket (disabled)
audit(1123206963.180:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
PCI0 USB0 USB1 USB2 USB3 USB4 USB5 USB6 LAN0 AC97 MC97 UAR1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4236KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 12 (level, low) -> IRQ 12
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xbc00-0xbc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: ST380021A, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
Probing IDE interface ide1...
hdd: CD-224E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Stopping tasks: ==|
Freeing memory... -\|/done (455 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 1413680k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdd: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
lp: driver loaded but no devices found
mice: PS/2 mouse device common for all mice
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins at debian.org>
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel at redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
hdd: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdd: packet command error: error=0x54
ide: failed opcode was 100
cdrom: open failed.
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.10-5-386
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: Maximum main memory to use for agp memory: 409M
agpgart: AGP aperture is 64M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 12 (level, low) -> IRQ 12
Yenta: CardBus bridge found at 0000:00:0a.0 [1106:aa01]
yenta 0000:00:0a.0: Preassigned resource 0 busy, reconfiguring...
Yenta: ISA IRQ mask 0x0c00, PCI irq 12
Socket status: 30000820
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI interrupt 0000:00:0a.1[B] -> GSI 7 (level, low) -> IRQ 7
Yenta: CardBus bridge found at 0000:00:0a.1 [1106:aa01]
Yenta: ISA IRQ mask 0x0c00, PCI irq 7
Socket status: 30000006
PCI: Failed to allocate mem resource #0:10000 at ea010000 for 0000:02:00.0
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.12.14 (AR5210, AR5211, AR5212)
wlan: 0.8.4.5 (EXPERIMENTAL)
ath_rate_onoe: 1.0
ath_pci: 0.9.4.12 (EXPERIMENTAL)
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 12 (level, low) -> IRQ 12
ath_pci: cannot reserve PCI memory region
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 12, io base 0xb000
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[B] -> GSI 7 (level, low) -> IRQ 7
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: irq 7, io base 0xb400
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:10.2[C] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: irq 5, io base 0xb800
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
usbcore: registered new driver hiddev
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:10.0-2
input: USB HID v1.10 Device [Logitech USB Receiver] on usb-0000:00:10.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
ACPI: PCI interrupt 0000:00:10.3[D] -> GSI 7 (level, low) -> IRQ 7
ehci_hcd 0000:00:10.3: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.3: irq 7, pci mem 0xea00a000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
drivers/usb/input/hid-core.c: input irq status -84 received
drivers/usb/input/hid-core.c: input irq status -84 received
usb 1-2: USB disconnect, address 2
usb 1-2: new low speed USB device using uhci_hcd and address 3
irda_init()
NET: Registered protocol family 23
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:10.0-2
input: USB HID v1.10 Device [Logitech USB Receiver] on usb-0000:00:10.0-2
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:11.5 to 64
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:00:12.0[A] -> GSI 12 (level, low) -> IRQ 12
eth0: VIA Rhine II at 0xc800, 00:40:63:dd:41:f4, IRQ 12.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link cde1.
eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
drivers/usb/input/hid-input.c: event field not found
drivers/usb/input/hid-input.c: event field not found
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
cs: IO port probe 0x0100-0x04ff: excluding 0x418-0x47f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
iomem_reserved:
******************************************************
00000000-0009ffff : System RAM
000a0000-000bffff : Video RAM area
000c0000-000cdfff : Video ROM
000f0000-000fffff : System ROM
00100000-1dfeffff : System RAM
00100000-0026676a : Kernel code
0026676b-00322bff : Kernel data
1dff0000-1dff2fff : ACPI Non-volatile Storage
1dff3000-1dffffff : ACPI Tables
1e000000-1e3fffff : PCI CardBus #02
e0000000-e3ffffff : 0000:00:00.0
e4000000-e7ffffff : PCI Bus #01
e4000000-e7ffffff : 0000:01:00.0
e8000000-e9ffffff : PCI Bus #01
e8000000-e8ffffff : 0000:01:00.0
ea000000-ea000fff : 0000:00:0a.0
ea000000-ea000fff : yenta_socket
ea003000-ea004fff : PCI CardBus #02
ea005000-ea005fff : 0000:00:0a.1
ea005000-ea005fff : yenta_socket
ea006000-ea007fff : PCI CardBus #06
ea008000-ea009fff : PCI CardBus #06
ea00a000-ea00a0ff : 0000:00:10.3
ea00a000-ea00a0ff : ehci_hcd
ea00b000-ea00b0ff : 0000:00:12.0
ea00b000-ea00b0ff : via-rhine
ffff0000-ffffffff : reserved
More information about the linux-pcmcia
mailing list