no power to PCMCIA card
Micah Wedemeyer
fanmail at micah-wedemeyer.net
Sun Sep 26 22:09:53 EDT 2004
This is regarding my attempt at getting my Netgear WG511 wireless PCMCIA card to
work. I know this mailing list specializes in this sort of stuff, so here goes.
If more information is needed, please let me know and I will try and collect
it.
The problem, as always, is that the card is not getting power. There are 2
lights on the card, neither is ever lit. I can use iwconfig to query eth1 for
information and I can also change the settings for eth1. When I use ifconfig to
bring eth1 up, I cannot seem to contact the network.
Also, before anything else, I would like to thank the PCMCIA
kernel-hacker/developers for all their hard work in fixing the problems of noobs
like me :)
So, without any further ado, here is all the various information I can gather:
System: Via EPIA-MII 10,000 motherboard
Cardbus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Kernel: Fedora Core 2 2.6.8-1.521
Output of lspci (with card inserted):
-------------------------------------
00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller
(rev 80)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(rev 80)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(rev 80)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(rev 80)
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237
AC97 Audio Controller (rev 50)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
00:14.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416)
MPEG-2 Encoder (rev 01)
01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266]
integrated CastleRock graphics (rev 03)
02:00.0 Network controller: Intersil Corporation Intersil ISL3890 [Prism
GT/Prism Duette] (rev 01)
Output of dmesg when INSERTING card:
------------------------------------
cs: pcmcia_socket0: unable to apply power.
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 12 (level, low) -> IRQ 12
divert: allocating divert_blk for eth1
Output of dmesg when REMOVING card:
-----------------------------------
eth1: hot unplug detected
eth1: removing device
divert: freeing divert_blk for eth1
Output of cbdump with card REMOVED:
-----------------------------------
00:0a.0 CardBus bridge: Gammagraphx, Inc.: Unknown device 0000
-- generic cardbus config registers
Vendor ID [00] : 0x1180
Device ID [02] : 0x0476
PCI command [04] : 0x0007
Base address [10] : 0xe200c000
Memory Base 0 [1c] : 0xe2000000
Memory Limit 0 [20] : 0xe2001000
Memory Base 1 [24] : 0xe2002000
Memory Limit 1 [28] : 0xe2003000
IO Base 0 [2c] : 0x00009000
IO Limit 0 [30] : 0x00009400
IO Base 1 [34] : 0x00009800
IO Limit 1 [38] : 0x00009c00
Bridge control [3e] : 0x0500
Subsystem vendor ID [40] : 0x1106
Subsystem device ID [42] : 0xaa01
Legacy mode base [44] : 0x0001
-- cardbus registers
CB_SOCKET_EVENT [00] : 0x00000000
CB_SOCKET_MASK [04] : 0x00000006
CB_SOCKET_STATE [08] : 0x30000826
CB_SOCKET_FORCE [0c] : 0x00000000
CB_SOCKET_CONTROL [10] : 0x00000400
CB_SOCKET_POWER [20] : 0x00000000
-- exca registers
I365_IDENT [00] : 0x83
I365_STATUS [01] : 0x33
I365_POWER [02] : 0x00
I365_INTCTL [03] : 0x00
I365_CSC [04] : 0x00
I365_CSCINT [05] : 0x00
I365_ADDRWIN [06] : 0x00
I365_IOCTL [07] : 0x00
I365_GENCTL [16] : 0x0000
I365_GBLCTL [1e] : 0x0000
I365_IO0_START [08] : 0x0000
I365_IO0_STOP [0a] : 0x0001
I365_IO1_START [0c] : 0x0000
I365_IO1_STOP [0e] : 0x0001
I365_MEM0_START [10] : 0x0000
I365_MEM0_STOP [12] : 0x0000
I365_MEM0_OFF [14] : 0x0000
I365_MEM0_PAGE [40] : 0x00
I365_MEM1_START [18] : 0x0000
I365_MEM1_STOP [1a] : 0x0000
I365_MEM1_OFF [1c] : 0x0000
I365_MEM1_PAGE [41] : 0x00
I365_MEM2_START [20] : 0x0000
I365_MEM2_STOP [22] : 0x0000
I365_MEM2_OFF [24] : 0x0000
I365_MEM2_PAGE [42] : 0x00
I365_MEM3_START [28] : 0x0000
I365_MEM3_STOP [2a] : 0x0000
I365_MEM3_OFF [2c] : 0x0000
I365_MEM3_PAGE [43] : 0x00
I365_MEM4_START [30] : 0x0000
I365_MEM4_STOP [32] : 0x0000
I365_MEM4_OFF [34] : 0x0000
I365_MEM4_PAGE [44] : 0x00
00:0a.1 CardBus bridge: Gammagraphx, Inc.: Unknown device 0000
-- generic cardbus config registers
Vendor ID [00] : 0x1180
Device ID [02] : 0x0476
PCI command [04] : 0x0007
Base address [10] : 0xe2004000
Memory Base 0 [1c] : 0xe2005000
Memory Limit 0 [20] : 0xe2006000
Memory Base 1 [24] : 0xe2007000
Memory Limit 1 [28] : 0xe2008000
IO Base 0 [2c] : 0x0000a000
IO Limit 0 [30] : 0x0000a400
IO Base 1 [34] : 0x0000a800
IO Limit 1 [38] : 0x0000ac00
Bridge control [3e] : 0x0580
Subsystem vendor ID [40] : 0x1106
Subsystem device ID [42] : 0xaa01
Legacy mode base [44] : 0x0001
-- cardbus registers
CB_SOCKET_EVENT [00] : 0x00000000
CB_SOCKET_MASK [04] : 0x00000006
CB_SOCKET_STATE [08] : 0x30000006
CB_SOCKET_FORCE [0c] : 0x00000000
CB_SOCKET_CONTROL [10] : 0x00000400
CB_SOCKET_POWER [20] : 0x00000000
-- exca registers
I365_IDENT [00] : 0x83
I365_STATUS [01] : 0x33
I365_POWER [02] : 0x40
I365_INTCTL [03] : 0x40
I365_CSC [04] : 0x00
I365_CSCINT [05] : 0x08
I365_ADDRWIN [06] : 0x00
I365_IOCTL [07] : 0x00
I365_GENCTL [16] : 0x0000
I365_GBLCTL [1e] : 0x0000
I365_IO0_START [08] : 0x0000
I365_IO0_STOP [0a] : 0x0001
I365_IO1_START [0c] : 0x0000
I365_IO1_STOP [0e] : 0x0001
I365_MEM0_START [10] : 0x0000
I365_MEM0_STOP [12] : 0x0000
I365_MEM0_OFF [14] : 0x0000
I365_MEM0_PAGE [40] : 0x00
I365_MEM1_START [18] : 0x0000
I365_MEM1_STOP [1a] : 0x0000
I365_MEM1_OFF [1c] : 0x0000
I365_MEM1_PAGE [41] : 0x00
I365_MEM2_START [20] : 0x0000
I365_MEM2_STOP [22] : 0x0000
I365_MEM2_OFF [24] : 0x0000
I365_MEM2_PAGE [42] : 0x00
I365_MEM3_START [28] : 0x0000
I365_MEM3_STOP [2a] : 0x0000
I365_MEM3_OFF [2c] : 0x0000
I365_MEM3_PAGE [43] : 0x00
I365_MEM4_START [30] : 0x0000
I365_MEM4_STOP [32] : 0x0000
I365_MEM4_OFF [34] : 0x0000
I365_MEM4_PAGE [44] : 0x00
output of cbdump with card INSERTED:
------------------------------------
00:0a.0 CardBus bridge: Gammagraphx, Inc.: Unknown device 0000
-- generic cardbus config registers
Vendor ID [00] : 0x1180
Device ID [02] : 0x0476
PCI command [04] : 0x0007
Base address [10] : 0xe200c000
Memory Base 0 [1c] : 0xe2000000
Memory Limit 0 [20] : 0xe2001000
Memory Base 1 [24] : 0xe2002000
Memory Limit 1 [28] : 0xe2003000
IO Base 0 [2c] : 0x00009000
IO Limit 0 [30] : 0x00009400
IO Base 1 [34] : 0x00009800
IO Limit 1 [38] : 0x00009c00
Bridge control [3e] : 0x0500
Subsystem vendor ID [40] : 0x1106
Subsystem device ID [42] : 0xaa01
Legacy mode base [44] : 0x0001
-- cardbus registers
CB_SOCKET_EVENT [00] : 0x00000000
CB_SOCKET_MASK [04] : 0x00000006
CB_SOCKET_STATE [08] : 0x30000829
CB_SOCKET_FORCE [0c] : 0x00000000
CB_SOCKET_CONTROL [10] : 0x00000433
CB_SOCKET_POWER [20] : 0x00000000
-- exca registers
I365_IDENT [00] : 0x83
I365_STATUS [01] : 0x6f
I365_POWER [02] : 0x13
I365_INTCTL [03] : 0x00
I365_CSC [04] : 0x00
I365_CSCINT [05] : 0x00
I365_ADDRWIN [06] : 0x00
I365_IOCTL [07] : 0x00
I365_GENCTL [16] : 0x0000
I365_GBLCTL [1e] : 0x0000
I365_IO0_START [08] : 0x0000
I365_IO0_STOP [0a] : 0x0001
I365_IO1_START [0c] : 0x0000
I365_IO1_STOP [0e] : 0x0001
I365_MEM0_START [10] : 0x0000
I365_MEM0_STOP [12] : 0x0000
I365_MEM0_OFF [14] : 0x0000
I365_MEM0_PAGE [40] : 0x00
I365_MEM1_START [18] : 0x0000
I365_MEM1_STOP [1a] : 0x0000
I365_MEM1_OFF [1c] : 0x0000
I365_MEM1_PAGE [41] : 0x00
I365_MEM2_START [20] : 0x0000
I365_MEM2_STOP [22] : 0x0000
I365_MEM2_OFF [24] : 0x0000
I365_MEM2_PAGE [42] : 0x00
I365_MEM3_START [28] : 0x0000
I365_MEM3_STOP [2a] : 0x0000
I365_MEM3_OFF [2c] : 0x0000
I365_MEM3_PAGE [43] : 0x00
I365_MEM4_START [30] : 0x0000
I365_MEM4_STOP [32] : 0x0000
I365_MEM4_OFF [34] : 0x0000
I365_MEM4_PAGE [44] : 0x00
00:0a.1 CardBus bridge: Gammagraphx, Inc.: Unknown device 0000
-- generic cardbus config registers
Vendor ID [00] : 0x1180
Device ID [02] : 0x0476
PCI command [04] : 0x0007
Base address [10] : 0xe2004000
Memory Base 0 [1c] : 0xe2005000
Memory Limit 0 [20] : 0xe2006000
Memory Base 1 [24] : 0xe2007000
Memory Limit 1 [28] : 0xe2008000
IO Base 0 [2c] : 0x0000a000
IO Limit 0 [30] : 0x0000a400
IO Base 1 [34] : 0x0000a800
IO Limit 1 [38] : 0x0000ac00
Bridge control [3e] : 0x0580
Subsystem vendor ID [40] : 0x1106
Subsystem device ID [42] : 0xaa01
Legacy mode base [44] : 0x0001
-- cardbus registers
CB_SOCKET_EVENT [00] : 0x00000000
CB_SOCKET_MASK [04] : 0x00000006
CB_SOCKET_STATE [08] : 0x30000006
CB_SOCKET_FORCE [0c] : 0x00000000
CB_SOCKET_CONTROL [10] : 0x00000400
CB_SOCKET_POWER [20] : 0x00000000
-- exca registers
I365_IDENT [00] : 0x83
I365_STATUS [01] : 0x33
I365_POWER [02] : 0x40
I365_INTCTL [03] : 0x40
I365_CSC [04] : 0x00
I365_CSCINT [05] : 0x08
I365_ADDRWIN [06] : 0x00
I365_IOCTL [07] : 0x00
I365_GENCTL [16] : 0x0000
I365_GBLCTL [1e] : 0x0000
I365_IO0_START [08] : 0x0000
I365_IO0_STOP [0a] : 0x0001
I365_IO1_START [0c] : 0x0000
I365_IO1_STOP [0e] : 0x0001
I365_MEM0_START [10] : 0x0000
I365_MEM0_STOP [12] : 0x0000
I365_MEM0_OFF [14] : 0x0000
I365_MEM0_PAGE [40] : 0x00
I365_MEM1_START [18] : 0x0000
I365_MEM1_STOP [1a] : 0x0000
I365_MEM1_OFF [1c] : 0x0000
I365_MEM1_PAGE [41] : 0x00
I365_MEM2_START [20] : 0x0000
I365_MEM2_STOP [22] : 0x0000
I365_MEM2_OFF [24] : 0x0000
I365_MEM2_PAGE [42] : 0x00
I365_MEM3_START [28] : 0x0000
I365_MEM3_STOP [2a] : 0x0000
I365_MEM3_OFF [2c] : 0x0000
I365_MEM3_PAGE [43] : 0x00
I365_MEM4_START [30] : 0x0000
I365_MEM4_STOP [32] : 0x0000
I365_MEM4_OFF [34] : 0x0000
I365_MEM4_PAGE [44] : 0x00
output of lspci -vv with card INSERTED:
---------------------------------------
00:00.0 Host bridge: VIA Technologies, Inc. VT8623 [Apollo CLE266]
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable)
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3-
Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dbffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 12
Region 0: Memory at e200c000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: e2000000-e2001000 (prefetchable)
Memory window 1: e2002000-e2003000
I/O window 0: 00009000-00009403
I/O window 1: 00009800-00009c03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 5
Region 0: Memory at e2004000 (32-bit, non-prefetchable)
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: e2005000-e2006000 (prefetchable)
Memory window 1: e2007000-e2008000
I/O window 0: 0000a000-0000a403
I/O window 1: 0000a800-0000ac03
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller
(rev 80) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (8000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e2009000 (32-bit, non-prefetchable)
Region 1: I/O ports at b000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at b400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at b800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin C routed to IRQ 7
Region 4: I/O ports at bc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20
[EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Interrupt: pin D routed to IRQ 12
Region 0: Memory at e200a000 (32-bit, non-prefetchable)
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 12
Region 4: I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237
AC97 Audio Controller (rev 50)
Subsystem: VIA Technologies, Inc.: Unknown device aa01
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 7
Region 0: I/O ports at c400
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller
on VT8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at cc00
Region 1: Memory at e200b000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.0 Multimedia video controller: Internext Compression Inc iTVC16 (CX23416)
MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR 250
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (32000ns min, 2000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at dc000000 (32-bit, prefetchable)
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: VIA Technologies, Inc. VT8623 [Apollo CLE266]
integrated CastleRock graphics (rev 03) (prog-if 00 [VGA])
Subsystem: VIA Technologies, Inc. VT8623 [Apollo CLE266] integrated CastleRock
graphics
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 12
Region 0: Memory at d8000000 (32-bit, prefetchable)
Region 1: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3-
Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
02:00.0 Network controller: Intersil Corporation Intersil ISL3890 [Prism
GT/Prism Duette] (rev 01)
Subsystem: Netgear: Unknown device 4800
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 7000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 12
Region 0: Memory at e2002000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
More information about the linux-pcmcia
mailing list