[PATCH v4 11/11] mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600

Pratyush Yadav p.yadav at ti.com
Wed Mar 30 12:49:16 PDT 2022


> Subject: [PATCH v4 11/11] mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600

Nitpick: s/mtd: spi-nor: aspeed:/spi: aspeed:/

On 25/03/22 11:08AM, Cédric Le Goater wrote:
> From: Potin Lai <potin.lai at quantatw.com>
> 
> In AST2600, the unit of SPI CEx decoding range register is 1MB, and end
> address offset is set to the acctual offset - 1MB. If the flash only has
> 1MB, the end address will has same value as start address, which will
> causing unexpected errors.
> 
> This patch set the decoding size to at least 2MB to avoid decoding errors.
> 
> Tested:
> root at bletchley:~# dmesg | grep "aspeed-smc 1e631000.spi: CE0 window"
> [   59.328134] aspeed-smc 1e631000.spi: CE0 window resized to 2MB (AST2600 Decoding)
> [   59.343001] aspeed-smc 1e631000.spi: CE0 window [ 0x50000000 - 0x50200000 ] 2MB
> root at bletchley:~# devmem 0x1e631030
> 0x00100000
> 
> Signed-off-by: Potin Lai <potin.lai at quantatw.com>
> [ clg : Ported on new spi-mem driver ]
> Signed-off-by: Cédric Le Goater <clg at kaod.org>
> ---
>  drivers/spi/spi-aspeed-smc.c | 13 +++++++++++++
>  1 file changed, 13 insertions(+)
> 
> diff --git a/drivers/spi/spi-aspeed-smc.c b/drivers/spi/spi-aspeed-smc.c
> index 660451667a39..227797e13997 100644
> --- a/drivers/spi/spi-aspeed-smc.c
> +++ b/drivers/spi/spi-aspeed-smc.c
> @@ -466,6 +466,8 @@ static int aspeed_spi_set_window(struct aspeed_spi *aspi,
>   *   is correct.
>   */
>  static const struct aspeed_spi_data ast2500_spi_data;
> +static const struct aspeed_spi_data ast2600_spi_data;
> +static const struct aspeed_spi_data ast2600_fmc_data;
>  
>  static int aspeed_spi_chip_adjust_window(struct aspeed_spi_chip *chip,
>  					 u32 local_offset, u32 size)
> @@ -489,6 +491,17 @@ static int aspeed_spi_chip_adjust_window(struct aspeed_spi_chip *chip,
>  			 chip->cs, size >> 20);
>  	}
>  
> +	/*
> +	 * The decoding size of AST2600 SPI controller should set at
> +	 * least 2MB.
> +	 */
> +	if ((aspi->data == &ast2600_spi_data || aspi->data == &ast2600_fmc_data) &&
> +	    size < SZ_2M) {
> +		size = SZ_2M;
> +		dev_info(aspi->dev, "CE%d window resized to %dMB (AST2600 Decoding)",
> +			 chip->cs, size >> 20);
> +	}
> +
>  	aspeed_spi_get_windows(aspi, windows);
>  
>  	/* Adjust this chip window */
> -- 
> 2.34.1
> 

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.



More information about the linux-mtd mailing list