[PATCH RFC] memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual mode

[Krzysztof Kozlowski]

On 11/03/2022 17:53, Geert Uytterhoeven wrote:
> HyperFlash devices fail to probe:
> 
>     rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed
> 
> In HyperFLASH or Octal-SPI Flash mode, the Transfer Data Enable bits
> (SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived
> from half of the transfer size, cfr. the rpcif_bits_set() helper
> function.
> 
> Hence when converting back from Transfer Data Enable bits to transfer
> size, the bus width must be taken into account, and all Manual Mode Data
> Register access sizes must be doubled when communicating with a
> HyperFLASH or Octal-SPI Flash device.
> 
> Fixes: fff53a551db50f5e ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode")
> Signed-off-by: Geert Uytterhoeven <geert+renesas at glider.be>
> ---
> Marked RFC, a (1) we should avoid the back-and-forth conversion between
> transfer size and Transfer Data Enable bits, and (2) actual HyperFlash
> data reads (which follows a completely different code path) still return
> all zeros.
> 
> On Salvator-XS with unlocked HyperFlash, the HyperFlash is now detected
> again, cfr. (with DEBUG_CFI enabled):
> 
>     Number of erase regions: 1
>     Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
>     Primary Algorithm Table at 0040
>     Alternative Vendor Command Set: 0000 (None)
>     No Alternate Algorithm Table
>     Vcc Minimum:  1.7 V
>     Vcc Maximum:  1.9 V
>     No Vpp line
>     Typical byte/word write timeout: 512 \xc2\xb5s
>     Maximum byte/word write timeout: 2048 \xc2\xb5s
>     Typical full buffer write timeout: 512 \xc2\xb5s
>     Maximum full buffer write timeout: 2048 \xc2\xb5s
>     Typical block erase timeout: 1024 ms
>     Maximum block erase timeout: 4096 ms
>     Typical chip erase timeout: 262144 ms
>     Maximum chip erase timeout: 1048576 ms
>     Device size: 0x4000000 bytes (64 MiB)
>     Flash Device Interface description: 0x0000
>       - x8-only asynchronous interface
>     Max. bytes in buffer write: 0x200
>     Number of Erase Block Regions: 1
>       Erase Region #0: BlockSize 0x40000 bytes, 256 blocks
>     rpc-if-hyperflash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x007000
>     Amd/Fujitsu Extended Query Table at 0x0040
>       Amd/Fujitsu Extended Query version 1.5.
>     rpc-if-hyperflash: CFI contains unrecognised boot bank location (0). Assuming bottom.
>     number of CFI chips: 1
> 
> At first, the failure looked like an endianness-issue, as reading two
> bytes resulted in e.g. 0x51 0x00 instead of 0x00 0x51.  But it turned
> out to be reading a single 8-bit value of 0x51 instead of a 16-bit value
> of 0x5100.
> 
> Note that commit 0d37f69cacb33435 ("memory: renesas-rpc-if: Correct QSPI
> data transfer in Manual mode") in the BSP does not suffer from this bug,
> as it bases its decision on the real number of bytes to transfer, not on
> the SMENR.SPIDE register bits.
> ---
>  drivers/memory/renesas-rpc-if.c | 20 ++++++++++++++++----
>  1 file changed, 16 insertions(+), 4 deletions(-)
>

Some reviews and tests will be useful. Anyway it's too late upcoming
cycle, so I will pick it up after merge window.


Best regards,
Krzysztof