[PATCH v13 4/4] mtd: spi-nor: spansion: Add s25hl-t/s25hs-t IDs and fixups

[Tudor.Ambarus at microchip.com]

On 4/21/22 12:40, tkuw584924 at gmail.com wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> 
> From: Takahiro Kuwano <Takahiro.Kuwano at infineon.com>
> 
> The S25HL-T/S25HS-T family is the Infineon SEMPER Flash with Quad SPI.
> 
> For the single-die package parts (512Mb and 1Gb), only bottom 4KB and
> uniform sector sizes are supported. This is due to missing or incorrect
> entries in SMPT. Fixup for other sector sizes configurations will be
> followed up as needed.
> 
> Tested on Xilinx Zynq-7000 FPGA board.
> 
> Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano at infineon.com>
> ---
> Changes in v13:
>   - Remove part specific set_4byte_addr_mode()
>   - Revert SNOR_F_4B_OPCODES
>   - Add post_sfdp to fix 3 byte erase opcode in 4BAIT
> 
> Changes in v12:
>   - Cleanup fixups based on other patches in this series
>   - Add part specific set_4byte_addr_mode()
>   - Unset SNOR_F_4B_OPCODES flag to let core to call set_4byte_addr_mode
> 
> Changes in v11:
>   - Cleanup fixups based on other patches in this series
> 
> Changes in v10:
>   - Cleanup fixups and ID table based on other patches in this series
> 
> Changes in v9:
>   - Use late_init() hook to fix mode clocks and writesize
>   - Use PARSE_SFDP instead of NO_SFDP_FLAGS
>   - Use MFR_FLAGS for USE_CLSR
>   - Add comment block to explain about addr mode in post_bfpt_fixups()
> 
> Changes in v8:
>   - Call write_disable in error case only
>   - Use spi_nor_read_reg() helper
>   - Use nor->bouncebuf instead of variable on stack
>   - Update ID table to use FLAGS macro
> 
> Changes in v7:
>   - Add missing device info table in v6
> 
> Changes in v6:
>   - Remove 2Gb multi die pacakge support
> 
> Changes in v5:
>   - Add NO_CHIP_ERASE flag to S25HL02GT and S25HS02GT
> 
> Changes in v4:
>   - Merge block comments about SMPT in s25hx_t_post_sfdp_fixups()
>   - Remove USE_CLSR flags from S25HL02GT and S25HS02GT
> 
> Changes in v3:
>   - Remove S25HL256T and S25HS256T
>   - Add S25HL02GT and S25HS02GT
>   - Add support for multi-die package parts support
>   - Remove erase_map fix for top/split sector layout
>   - Set ECC data unit size (16B) to writesize
> 
>  drivers/mtd/spi-nor/spansion.c | 66 ++++++++++++++++++++++++++++++++++
>  1 file changed, 66 insertions(+)
> 
> diff --git a/drivers/mtd/spi-nor/spansion.c b/drivers/mtd/spi-nor/spansion.c
> index 952d4383f9da..e56c48c3280b 100644
> --- a/drivers/mtd/spi-nor/spansion.c
> +++ b/drivers/mtd/spi-nor/spansion.c
> @@ -203,6 +203,56 @@ static int cypress_nor_set_page_size(struct spi_nor *nor)
>         return 0;
>  }
> 
> +static int
> +s25hx_t_post_bfpt_fixup(struct spi_nor *nor,
> +                       const struct sfdp_parameter_header *bfpt_header,
> +                       const struct sfdp_bfpt *bfpt)
> +{
> +       /* Replace Quad Enable with volatile version */
> +       nor->params->quad_enable = cypress_nor_quad_enable_volatile;
> +
> +       return cypress_nor_set_page_size(nor);
> +}
> +
> +static void s25hx_t_post_sfdp_fixup(struct spi_nor *nor)
> +{
> +       struct spi_nor_erase_type *erase_type =
> +                                       nor->params->erase_map.erase_type;
> +       int i;
> +
> +       /*
> +        * In some parts, 3byte erase opcodes are advertised by 4BAIT.
> +        * Convert them to 4byte erase opcodes.

this is a fix, those opcodes don't work with 4 byte addresses, right?
Looks good!
Reviewed-by: Tudor Ambarus <tudor.ambarus at microchip.com>

> +        */
> +       for (i = 0; i < SNOR_ERASE_TYPE_MAX; i++) {
> +               switch (erase_type[i].opcode) {
> +               case SPINOR_OP_SE:
> +                       erase_type[i].opcode = SPINOR_OP_SE_4B;
> +                       break;
> +               case SPINOR_OP_BE_4K:
> +                       erase_type[i].opcode = SPINOR_OP_BE_4K_4B;
> +                       break;
> +               default:
> +                       break;
> +               }
> +       }
> +}
> +
> +static void s25hx_t_late_init(struct spi_nor *nor)
> +{
> +       /* Fast Read 4B requires mode cycles */
> +       nor->params->reads[SNOR_CMD_READ_FAST].num_mode_clocks = 8;
> +
> +       /* The writesize should be ECC data unit size */
> +       nor->params->writesize = 16;
> +}
> +
> +static struct spi_nor_fixups s25hx_t_fixups = {
> +       .post_bfpt = s25hx_t_post_bfpt_fixup,
> +       .post_sfdp = s25hx_t_post_sfdp_fixup,
> +       .late_init = s25hx_t_late_init,
> +};
> +
>  /**
>   * cypress_nor_octal_dtr_enable() - Enable octal DTR on Cypress flashes.
>   * @nor:               pointer to a 'struct spi_nor'
> @@ -379,6 +429,22 @@ static const struct flash_info spansion_nor_parts[] = {
>         { "s25fl256l",  INFO(0x016019,      0,  64 * 1024, 512)
>                 NO_SFDP_FLAGS(SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)
>                 FIXUP_FLAGS(SPI_NOR_4B_OPCODES) },
> +       { "s25hl512t",  INFO6(0x342a1a, 0x0f0390, 256 * 1024, 256)
> +               PARSE_SFDP
> +               MFR_FLAGS(USE_CLSR)
> +               .fixups = &s25hx_t_fixups },
> +       { "s25hl01gt",  INFO6(0x342a1b, 0x0f0390, 256 * 1024, 512)
> +               PARSE_SFDP
> +               MFR_FLAGS(USE_CLSR)
> +               .fixups = &s25hx_t_fixups },
> +       { "s25hs512t",  INFO6(0x342b1a, 0x0f0390, 256 * 1024, 256)
> +               PARSE_SFDP
> +               MFR_FLAGS(USE_CLSR)
> +               .fixups = &s25hx_t_fixups },
> +       { "s25hs01gt",  INFO6(0x342b1b, 0x0f0390, 256 * 1024, 512)
> +               PARSE_SFDP
> +               MFR_FLAGS(USE_CLSR)
> +               .fixups = &s25hx_t_fixups },
>         { "cy15x104q",  INFO6(0x042cc2, 0x7f7f7f, 512 * 1024, 1)
>                 FLAGS(SPI_NOR_NO_ERASE) },
>         { "s28hs512t",   INFO(0x345b1a,      0, 256 * 1024, 256)
> --
> 2.25.1
>